CV Seq.
available
Elmyra 2 is a 4-voice digital/analog hybrid platform for microtonal sonic exploration, capable of creating anything from lush ambient soundscapes to gritty droning textures and shrieking noises, available as a 42 HP Eurorack module or semi-modular desktop synth. With 31 modulation targets, 4 polymetric sequencers, delay, additional per-voice effects, a choice of various filters, as well as onboard LFOs and utilities, it is essentially a purpose-built small modular system in itself. A set of preset cards (included) or electronic components like capacitors or diodes can be plugged into the front panel in order to change the sound character.Features:• 4 independent voices activated by touch or CV• wavetable-based complex oscillator engine, up to 12 oscillators in total, 1V/octave compatible• chromatic mode makes chords and harmonic sounds possible, microtonal scales supported• 41 patch points• 31 modulation targets• touchpads with analog envelopes that can be used as modulation sources• resonant filter switchable between:• boomy and aggressive multimode 2-pole state variable filter (low-pass, band-pass, high-pass)• creamy 4-pole low-pass ladder filter• delay with unhealthy amounts of feedback• lo-fi reverb• analog OUCH circuit: a unique combination of destructive distortion, waveshaping and filtering• sonic character can be customised by using special preset cards (set of 4 included) or components like diodes that can be plugged into the front panel• preset cards can be used with other Neutral Labs modules• external audio can be processed via audio input• 9 per-voice modulations and effects:• unison detune• dual sub-oscillators• saturation• bitmangler• sample rate reduction• noise• high-pass filter• low-pass filter• 2 LFOs: 1 sine, 1 complex morphable• 4 sequencers with arbitrary step length per voice (up to 128), allows polymetric structures• delay time and LFOs can be clock-synced or unsynced (tap tempo is also possible)• utilities• dual attenuator/buffered multiple/voltage generator• CV summing circuit• case made of plant-based bioplastic and native German oakwood• boutique synth handmade in GermanyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Pip contains two morphable CV generators/complex LFOs in 8 HP that can be synced to each other in predefined ratios, unsynced or phase-shifted between each other. You can choose from a large variety of preset waveforms, random waves or even record and morph your own external CV or knob movements.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 1 left
The MSK 008 Voltage-Controlled Octave Switch is a multifunction voltage processor. The module has two channels, each containing a whole-volt quantizer that maps its input to the nearest integer number of volts from -2 to +2; a three-position toggle switch that shifts the quantizer boundaries up or down by a volt; and a precision adder (with optional subtraction function).If you simply route a pitch CV through one of the unquantized CV1 inputs, it can be a performance control, allowing easy transposition up or down an octave at the flip of a switch. That might be useful for VCOs without their own built-in octave switches. With no input signal, it generates a selectable offset of -1, 0, or +1 volts; feed that into an attenuated exponential FM input somewhere and you get the same tactile control over any other interval transposition you choose.But the possibilities really open up when you start using more inputs. An LFO into the quantized input gives the effect of flipping the octave switch under CV control, keeping your hands free to wiggle elsewhere. Using the unquantized inputs, which are normalled across the two channels, you can transpose one sequence by another. The CV2 input can add or subtract, selectable during build by a solder jumper on the circuit board; in a default build, CV2 adds on the left channel and subtracts on the right, but do-it-yourselfers can change this selection, or design their own expanders to make it switchable on the fly.Combining the two channels, with or without other utility modules, allows more complex melody-shifting effects. And it doesn't have to be just for oscillator pitch control. Switching fixed-voltage offsets on filter cutoffs also makes for great drops and timbral shifts. (And try putting the result through a slew limiter!) The default sum and difference configuration allows the module to act as a "mid-side" encoder or decoder. With other patching it can be a flip-flop or a wavefolder.The MSK 008 is fast enough to work on audio. The quantizer is built from hardware comparators, without a microcontroller, and it can do simple bit-crushing effects across the whole audio spectrum. Each channel can also be a unity mixer for audio, with two regular inputs plus the output of the bit-crusher.Features:• Two channels and multiple CV functions in a small space• Flash-style comparator quantization - no microcontroller• Through-hole design for easy hand construction and maintenance• Connectors between boards, and panel controls mounted on a board - no flying wires• No compromises on build quality: real aluminum panel, not PCB material, with colour printing; nickel and gold plating on the circuit boards; close-tolerance metal film fixed resistors; multiturn trimmers.• Fully open design - no lock-inDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
REWIRE is a 4×4 sequential switch and versatile signal router that lets you reconfigure a modular patch on the fly without touching cables.The module offers four inputs and four independent outputs, each with level control, switching logic and real-time manipulation and is built for dynamic signal flow, generative systems and performance precision. Fully clocked, resettable, shiftable and divisible, REWIRE functions as a patch programmer and performance brain in just 8 HP.Applications range from rotating LFOs across destinations and shifting melodies between voices to remapping triggers for generative grooves, stepping audio through multiple FX chains rhythmically, or using the faders as a simple manual preset bank.Features:• 4 inputs – 4 independent outputs (4×4 routing matrix)• Per-output level attenuverter (precision gain for each destination)• Sequential-switch for automated step-based routing• Clock input for tempo-synced switching• Resettable and shiftable for pattern control and live manipulation• Divisible/ratio modes for polymetric or subdivided switching patterns• Real-time manipulation – change routing without touching cables• Works with audio, CV and triggers (low-latency switching)DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Meet Bib, Buzzrito, and Blueberry – three playful and powerful Plinky-inspired modules that bring rich sound design and expressive touch control to your Eurorack setup. Designed by Alex Evans (creator of Plinky) and Ray Yokell (CrazyEmperor893 of The Crey Emporium), these unique characters break out Plinky’s sensitivity into three specialized creatures: Bib, a stereo effect chain with drive, delay, and lush reverb; Buzzrito, a lively swarm oscillator with 2D touch control and CV-morphing presets; and Blueberry, a generative touch sequencer that responds to pressure and gesture with pitch and gate outputs. Each module stands strong on its own, but they shine even brighter together, combining tactile control and rich stereo sound.Features:Bib• Stereo drive, delay, and reverb effects with touch-based page selection• Real-time modulation via pressure-sensitive interface• CV input assignable to any parameter using tap-and-turn gesture• Rear TRS stereo I/O header (Intellijel-compatible) for line or headphone outputBuzzrito• Stereo swarm oscillator with 2D touchplate for preset morphing• Seven built-in presets with XY CV control and looping gesture recording• V/Oct and Gate inputs for easy integration into any Eurorack voice chainBlueberry• Generative touch sequencer with 5 pressure-sensitive pads• Record and play up to 5 pitch patterns with individual tunings• CV control for transposition, memory selection, clocking, and scrub• Clocked mode with expressive step sequencing and preserved dynamicsDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
nQuencer is a Eurorack module that turns the AtoV 16n faderbank into a step sequencer.Connect a 3.5mm stereo cable to the i2c socket, patch in a clock and get a pitch and gate output.When the nQuencer module receives a trigger at the Clock input it reads the state of the first 16n Faderbank fader and outputs a corresponding voltage at Output 1. At the next clock signal it will read the second fader and so on until it reaches the end and loops back to the start.Push the reset button or send a gate to the input to move back to the start.If a fader is at the very bottom no gate will be generated for that step in modes that output gates. The last fader that isn't at the bottom determines the length of the sequence.NOTE: Building the nQuencer module involves surface mount soldering using 0603 components and is therefore not recommended unless you have experience with similar projects. Aside from soldering tools you will require a multimeter to calibrate and suitable equipment to programthe microcontroller if you didn’t purchase one with your PCB.Features:Sixteen steps• up to 16 step sequence• out 1 outputs pitch and out 2 outputs a gate• reset button and input move back to the startTwo Eights• splits the 16n faderbank into two halves each with upto 8 steps• out 1 outputs pitch for the left half and out 2 for the right• clock advances both sequences or reset in advances sequence 2 (alt reset in)Transpose• splits the 16n faderbank into two halves each with upto 8 steps• values from the right half (up to 1v) are added to the left• out 1 outputs pitch and out 2 outputs a gate• clock advances both sequences or reset in advances sequence 2 (alt reset in)DJ• splits the 16n faderbank into two halves each with upto 8 steps but only one sequence at a time• reset button switches the output to the other sequence or reset in (alt reset in)• out 1 outputs pitch and out 2 outputs a gateOptions• hold the reset button to enter settings mode, use the faders to change settings and press the button to exit• direction up, down, up down, random• probability chance of a note firing• output voltage range max 1v, 2v, 3v, 4v• fader at bottom note off, output 0v, last fader not at bottom controls sequence length on/off• gate length• alternative reset input mode on/offQuantizer• root note• scale - chromatic (semitones), ionian (major), aeolian (natural minor), harmonic minor, dorian, phrygian, lydian, mixolydian, major pentatonic, minor pentatonic, blues, disabled (unquantised)DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The Robaux 3PT is a multimode three-channel control voltage generator.The handy knob with the triple ring-shaped voltage indicator makes the module the ideal performance tool.The Tripot has three control voltage channels which can be adjusted with three parameter trimmers.Instead of using the big knob, the device can also be controlled via the CV input.The module offers seven different modes. These include a performance tool, chord generator, random generator, quantizer, sequencer or LFO.Features:• 1 x CV In, unipolar 5V• 3 x CV Out, unipolar 5V• 3 x ring-shaped led display• 1 x push button• 1 x big knob• 9 x trimmersDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
The M185 is the most intuitive and playable Eurorack sequencer.It appeals as a hands-on performance orientated module for easy creation of complex melodic sequences.It is the original multi-step-per-stage sequencer that inspired the Metropolis and Metropolix modules.• Features an expansion header for chaining two M185s for 16 stage sequences• Lots more quantisation scales• Live X0X style Gate Pattern programmingOVERVIEW• 8 unique gate modes for creative rhythmic possibilities• A/B split mode for two separate sequences, like having two sequencers in one box• 2 channels of CV/GATE and MIDI I/O• 15 Quantise scales OR pure analogue microtonal CV outputINPUTS & OUTPUTS• 2 channels of CV and Gate outputs• Expansion header to connect two M185s for 16 stage sequences• Reset input [ shared with MIDI input ]• Sync output [ shared with CH2 gate ]• Bidirectional Clock I/O• MIDI input for MIDI clock in, MIDI note transpose• MIDI output for MIDI clock out, MIDI note outputSTAGE DETAILS• 8 stages, each with individual 1-8 step repeats per stage• 8 gate modes per stage [ Off, Once, All, 1/2, 1/3, 1/4, Probability or Programmable, and Long ]• Programmable gate patterns for 'on the fly' X0X style programming of gate triggersEVEN MORE DETAILS !• AB serial split sequence mode with 1-8 sequence repeats for AAABAAAB sequence structures• AB parallel split mode, for two separate simultaneous sequences that play at the same time• Root note offset and reset trigger options from sequence B to A• 2.5V / 5V voltage range selectable• MIDI note output including programmable velocity• MIDI to CV converter mode [wow]• Programmable glide per stage• Easy user upgradable firmware using MIDI sysex filesPLEASE NOTE THE KIT IS ONLY SUITABLE FOR EXPERIENCED BUILDERS.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
ODDS is a generative melodic looping sequencer for the Eurorack format. It generates notes based on random probability, and it is designed to be as musical as possible while maintaining a direct and minimalistic interface. It enables you to set a probability to generate random notes within a given octave, scale and chord structure.The module can via the LOOP switch either be set to indefinitely generate random notes, or be set to loop the last up to 64 steps. The V/OCT input acts as transposition within the chosen scale, making it easy to create chord progressions.Gate output voltage: 5 VCV output voltage range: 0-7 VDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
available
Designed with performance in mind, POLYSEQ delivers a flexible polyphonic step sequencing workflow. Any of the 8 memory slots can be programmed via external CV/GATE up to 64 steps in length. In playback mode, any of the three outputs can play back from any memory slot, making it possible to create polyphonic and polymetric sequences with low effort. POLYSEQ can be clocked internally with swing or externally via the clock input.Polyseq can be clocked internally (5-300 BPM) or externally. The internal clock has swing from 5 to 95% (Hold MODE and adjust the tempo pot).Beside CV and GATE, sequences can have rests, ties and glide. There’s also a skip function which steps forward in the sequence without overwriting anything. This is handy for editing sequences or changing the sequence length. Each channel can do forward, backward, ping-pong and random playback (Hold MODE and press channel switch to toggle through the modes). Each playback channel can also be clock divided from 1 through 8 (Hold MODE+CH and adjust the memory division rotary switch). Finally, each channel can be individually muted (Short press on channel switch, latching).DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Mal-2 is a random signal generator mainly intended as CV modulation source. It has 2 modes of operation to provide you with smooth random goodness. Imagine Eris herself lends you a third hand to keep your patches interesting.In the first mode the CHANGE knob morphs from a cubic interpolated (sine like shaped) random signal to a random walk function that could make a wallstreet broker delirious with joy.In the second mode the CHANGE knob sets the self similarity. On the minimum setting the signal is completely random. On the maximum setting the random sequence is locked to a repeating, identical 8 step sequence. In between the sequence seamlessly morphs to new shapes over time.This gives you a random CV where you can shape the bounds in which the chaos unfolds and goes far beyond a slew limited white noise.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The Automator is a hands-on, 2-channel tempo-synced CV and gate recorder for Eurorack, built around a large, expressive slider and intuitive controls. It captures your movements in real time, turning gestures into looping modulation patterns with precise timing. Requiring an external clock (4ppqn), Automator continuously records while idle and begins playback the moment you hit record, looping up to 4 bars. You can change loop length and tempo post-recording, and each channel—selectable via a button—is color-coded (red for channel 1, green for channel 2). CV is recorded via the slider, while gates are captured using a dedicated button, with high resolution and flexible timing. Whether you're drawing dynamic modulations or tight rhythmic triggers, Automator gives you a powerful and performative way to animate your patches.Features:• Dual-channel CV and Gate recorder with tempo sync• Dedicated Gate button for rhythmic trigger input• Supports loop lengths from ¼ bar to 4 bars• Channel selection button with color indication (Red = Ch1, Green = Ch2)• Real-time recording resolution (CV every 2ms, gates down to 50ms)• High gate density (up to 125 triggers per bar)• Recordings timestamped for accurate playback timing• Decoupled gate and CV recording for flexible pattern creation• Clock input (4 ppqn) with tempo scaling from 30 BPM upwards• Playback length can be changed after recording without losing dataDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The 8S is an 8 step sequencer in 8 HP with control over parameters of the sequence as reset, hold, random step and direction. It’s been designed to work with clock related signals like triggers or gates but any type of CV signals can be used at its inputs. The output signal path is completely analog and its range can be set as unipolar (0 to +5 volts) or bipolar (-5 to +5 volts) via jumper on the back.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Arplus combines a quantizer, CV-controlled arpeggiator and six-voice Karplus-Strong string synthesizer in a single Eurorack module. Its 31 scales range from Western diatonic modes to Arabic maqam, Indian melakarta, Japanese pentatonics and even quarter-, semi- and whole-tone divisions.The arpeggiator creates evolving patterns from the selected scale and chord, while the quantized 1V/oct output can drive other oscillators. Chords can contain up to eight notes, scales can be customized and parameters without dedicated CV inputs can be assigned through flexible CV mapping.The internal physical-modeling engine can pluck or bow up to six virtual strings, using either its internal excitation or an external audio burst. A resonant filter, contour control and three stereo routing modes shape sounds from tight staccato plucks to wide, sustained pads and resonating soundscapes.Features• Quantizer, arpeggiator and string synthesizer• 6-voice Karplus-Strong physical modeling• External audio input for custom excitation• 31 scales including microtonal scale families• Customizable scales and chords of up to 8 notes• CV-controllable arpeggiator patterns• Quantized 1V/oct output• Flexible CV mapping• Three stereo output modes• Resonant filter and adjustable contour• 20 HP, skiff-friendly Eurorack moduleDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.