Apollo View - CanCan
available
CanCan delivers studio-quality headphone amplification in a compact 4HP Eurorack module. Powered by high-current parallel op-amps, it drives headphones from 16 to 600 ohms with remarkable clarity, offering exceptional audio fidelity for any impedance.Designed for two independent headphone outputs, CanCan provides separate volume controls for precise monitoring in both solo and collaborative settings. Each channel uses a low-noise Baxandall active volume control, ensuring perfect left-right balance and stereo imaging.With built-in 8-segment LED program meters for peak or average signal monitoring, CanCan is a must-have tool for detailed audio tracking and mixing. Ideal for musicians and producers who demand clarity and precision in every headphone session.Features:• Low Output Impedance (0.5 Ohm): Ensures a high damping factor for precise control and exceptional low-frequency response• Universal Headphone Compatibility: Supports a broad impedance range of 16 to 600 Ohms• Multi-Stage Low Noise Design: Guarantees low distortion and high stability for true-to-source audio reproduction• High Output Current (Up to 140mA): For driving power-intensive headphones up to 600 Ohms with ease• Visual Feedback: Dual 8-segment LED program level meters for monitoring input signal levels• Output Flexibility: One output can be used for driving monitors (using a Y-splitter)• Full-Spectrum Audio Fidelity: Offers a 20Hz to 20kHz bandwidth, perfect for all audio experiences• Protection Features: Includes comprehensive RF and DC input protection with resettable fuses for short-circuit output safetyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€154.00*
Befaco / DivKid - Output Bus
available
The Output Bus is your ultimate output module: Presented by DivKid and Befaco, meant to be the last link in your modular chain!Inspired by pro audio and studio summing units the Output Bus allows for summing style mixing, external gear integration, soft clip limiting, flexible output types, headphone monitoring and level visualization.The module works great mixing all your other mixers in your setup, to return mono or stereo FX into the master bus and for bringing in external stereo line level gear with ease. All of this in just 8HP while also being able to visualize your final levels, output appropriate signals on the right cable type and monitor in headphones.Features:• Six stereo inputs.• Line/synth selector in input six.• Modular level minijack out.• 6,5 mm Jack balanced out.• Minijack and 6,5 mm phones out.• Led Vu-meter.• Soft clipping circuit at main output.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€155.00*
Befaco / Molten Modular - Motion MTR
sold out at the moment
Motion MTR allow you to mix, attenuate and invert signals while having clear visual feedback of their levels.Each channel can function as:• Audio level control with VU meter• CV attenuator with voltage meter• CV inverter with voltage meterEach input is normalled to 10v, so you can use each of them to generate fixed voltages. Also, the outputs of channels 1 and 2 are summed into Out 3 to be used as a mixer. Patch it wildly to make it work as an attenuverter with offset, as a mixer, a VU meter or a combination of them all!This module is designed in collaboration with Robin Vincent from Molten Modular.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€112.00*
Befaco / Molten Modular - Motion MTR 1U
only 2 left
This is the 1U version of the module, for the 3U standard version please check the other product!Motion MTR allow you to mix, attenuate and invert signals while having clear visual feedback of their levels.Each channel can function as:• Audio level control with VU meter• CV attenuator with voltage meter• CV inverter with voltage meterEach input is normalled to 10v, so you can use each of them to generate fixed voltages. Also, the outputs of channels 1, 2 and 3 are summed into Out 4 to be used as a mixPatch it wildly to make it work as an attenuverter with offset, as a mixer, a VU meter or a combination of them all!This module is designed in collaboration with Robin Vincent from Molten Modular.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€122.00*
Dannysound - VU Meters
only 2 left
The Dannysound VU Meters is designed to be used with 2 x Dynamics modules. The modules connect internally via 2x3 pin ribbon cables.The meters provide a visual representation of various signals within the Dynamics modules making settings easier.Controls For Each Channel:3 position toggle switch:1. C/E OUT – Monitor compressor/expander output.2. INPUT – Monitor Dynamics input level or external input if it’s used.3. C/E AMT – Monitor Dynamics compression/expansion amount.3 position toggle switch:1. HI SENS – High sensitivity setting, best for monitoring the C/E OUT signal of percussive sounds and drums etc.2. OFF – If you want to turn meters off. Note that this stops the needles moving but the backlights will stay on.3. LO SENS – Low sensitivity setting, best for monitoring the C/E AMT signal or anything that overloads the HI SENS setting.Features:• External input sockets for monitoring external sources.• Switch to select high or low meter sensitivity or off if the clicking needles get annoying!• Monitoring of the compression/expansion amount.• Monitoring of the unprocessed input level.• Monitoring of the compressor/expander output level.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€164.00*
Erica Synths - EDU DIY Compressor
available
Need some professional polish in your modular system? With this simple diode-based compressor, you can shape the dynamics of your sound, adding punch and consistency to your patches. Whether you’re looking to beef up your basslines, add sustain to your leads, or tame the peaks of your percussion, this circuit’s got you covered.Erica Synths and Moritz Klein - have developed a series of educational DIY kits under the brand name mki x es.EDU with one specific goal in mind: to teach people with little-to-no prior experience how to design analog synthesizer circuits from scratch. What you’ll find in the box is not simply meant to be soldered together and then disappear in your rack. Instead, we want to take you through the circuit design process step by step, explaining every choice we’ve made and how it impacts the finished module.NB! All kits in these series are simple and come with extensive user manuals which can be downloaded separately, therefore we will not provide customer support in case your DIY build fails to function or similar.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€79.90*
New
Erica Synths - EDU DIY Labor Scope
only 1 left
This add-on expands the DIY.EDU Labor into a powerful, standalone electronics workstation. It integrates essential measurement and analysis tools, making it ideal for circuit development, debugging and learning within modular synthesis or general electronics.With an oscilloscope, voltmeter, spectrometer and tuner on board, this module gives you the insight and feedback you need to better understand your signals and modules in real time.Designed for educational use, prototyping, and experimentation.Features:• 3-channel oscilloscope – two external inputs, one internal (Labor audio out)• Visualizes Lissajous curves for waveform comparison• Voltmeter with 10V range and 0.1V resolution• Real-time spectrometer with adjustable display modes• Built-in chromatic tuner for pitch analysis and calibration• Turns the DIY.EDU Labor into a complete test & measurement stationDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€73.90*