Building these DIY kits happens on your own risk. We can't do support or give a guarantee for correct function, because that depends on your own skills. Be responsible and check the building instructions before you buy. Thank you!



Wireless Patching Via Bodycontacts

The technique is as old as circuit bending and many synths and DIY gadgets have used it over the years: patching signals and modulations via bodycontacts. We did it in our first DIY synths many years ago when we were mostly doing workshops.

 

Now we made a module for integrating this technique into your modular synth. A combination of defined voltages plus the corresponding touch points. Here it is: the Touch Source!



Exploding Shed - Touch Source

-10V to +10V Voltage Source

Explore wireless patching through Touch Points! Touch Source generates voltages between -10V and +10V, in the center is a touch plate with GND/0V. Place the touch points on any CV input of a module and connect a voltage to the touch point via your fingers. Or connect two Touch Points from any input to output through your body. Rule #1 is: there are no rules!

Here is a review on Amazona (german) and some demo videos here and there.

 

Touch Source includes 2 black Touch Points and a power bus cable. Packs of 5 Touch Points are available separately in black or orange to visualize your signalflow.

 

Power ??mA @+12V, ??mA @-12V

Width 4 HP

Depth 23mm

 

*B-Stock might have not exact voltages due to resistor mismatch

 

The unit is pre-assembled and no DIY.

Exploding Shed - Touch Source

40,00 €

  • 0,03 kg
  • Available
  • Ships within 3-5 days1

Exploding Shed - Indicator Touch Points (+/- LED)

Pack of 2 Indicator Touch Points. These ones feature a bi-polar LED inside so you can easily detect the polarity of your signal. Of course you can use them in the same way like the original Touch Points.

They are assembled and no DIY.

Exploding Shed - Indicator Touch Points (+/- LED)

19,95 €

  • 0,03 kg
  • Available
  • Ships within 3-5 days1

Exploding Shed - Touch Points (Black)

5 Touch Points in black. We made them as an extension for our Touch Source, but of course you can use them without the module for wireless patching in your Eurorack system. We made them higher and smaller than comparable products or most DIY versions, so the Touch Points are easily accessible between cables and buttons in your system.

They are assembled and no DIY.

Exploding Shed - Touch Points (Black)

26,50 €

  • 0,03 kg
  • Sold out at the moment

Exploding Shed - Touch Points (Orange)

5 Touch Points in orange. We made them as an extension for our Touch Source, but of course you can use them without the module for wireless patching in your Eurorack system. We made them higher and smaller than comparable products or most DIY versions, so the Touch Points are easily accessible between cables and buttons in your system.

They are assembled and no DIY.

Exploding Shed - Touch Points (Orange)

26,50 €

  • 0,03 kg
  • Available
  • Ships within 3-5 days1

Christmas Tree Module

It's christmas time in your modular rack and this year we invented a proper christmas tree module! The LEDs of the tree change color and are used as oscillators to generate weirdo-sound. There are four sections with two LEDs each which modulate each other. You can patch the oscillator outs to the left or right output with mini-patch wires.

With this DIY kit you have 2 options:
1) The tree can be used standalone with a 9V battery as a simple light effect which is standing on a table etc. In this version there is no audio possible.
2) You complete the whole module and solder the tree to the panel. Then you can make use of the full audio possibilities.

This kit is perfect to build it with your kids or finally convince your partner, that modular maybe isn't that bad.

Width: 12 HP
Depth: 18mm
Power: ?mA @+12V, 0mA @-12V

Panel: Black FR4

This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Building instructions can be found here.
DIY level: Medium. Most is easy, but one SMD switch to solder.

Christmas Tree Module

19,00 €

  • 0,04 kg
  • Available
  • Ships within 3-5 days1

Christmas Module

Ok, a christmas module with pulsating lights, of course it does not make sound at all. But it’s for those nerds, who want to celebrate christmas in their Eurorack system. We made it for fun and we're sure, this is one of the easiest DIY projects in the entire world, possibly a good first soldering experience for your kids. 4 LEDs, 2 resistors and a power header.

Width 10 HP
Depth 15mm
Power ?mA @+12V, 0mA @-12V

This is a Do-It-Yourself kit, not an assembled module. A Bus-Cable is NOT included. Building instructions can be downloaded here soon.

DIY level: total no-brainer, even zombies can make it. Please download the building instructions here.

Christmas Module

4,90 €

  • 0,03 kg
  • Available
  • Ships within 3-5 days1

Christmas Ball

Another non-musical object, but fun. With this DIY kit you can possibly convince your kids and partner, that it’s a ok to spend all your cash in your hobby ;-) With this christmas ball, featuring pulsating lights you can contribute something to your family’s christmas tree. This is a very easy DIY project, maybe a first one for your kids. 3 LEDs, a switch and a battery holder.

Diameter 7,4cm
Depth 8mm
Power CR2032 battery (not included)

 

This is a Do-It-Yourself kit, not an assembled module. A CR2032 battery is NOT included. Building instructions can be downloaded here soon.

DIY level: so simple that you can still do it when you’re brain-dead. Please download the building instructions here.

Christmas Ball

4,50 €

  • 0,01 kg
  • Available
  • Ships within 3-5 days1