333modules - Dual PT
only 2 left
Double delay effect module based on two PT2399 chips mounted in series, noise and glitchy module with 4 different feedback points (2 pre-PT and 2 post-PT) and voltage controlled delay time.Features:• Two PT2399 chips in series• 4 x feedback pots• 2 x voltage controlled delay time• Dry / Wet• Trash, noise and glitchyDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€136.85*
4ms - Looping Delay
sold out at the moment
Crystal-clear clock-synced delay for loop up to 90 seconds, echoes, sound-on-sound, Karplus-Strong etc.Features:• Loop or echo time is synchronized to a clock• 87 seconds of delay/loop time maximum in mono mode, 43 seconds in stereo mode• 48kHz/24-bit sampling rate, loop recorded at 16-bit (24-bit optional)• Extremely quiet, low noise and low jitter design• Tap tempo button and clock Ping input set the basis for one "beat"• Delay/loop time set as a number of musical beats (or fractions of beats) using the Time knob, switch, and CV jack• Sample-accurate clock output for perfect synchronization• Loop clock output• Time switches change range of Time knob from 1/8th notes up to 32 bars• Digital feedback, up to 110%• Delay Feed control, independent of dry/wet signal mix• Infinite Hold mode disables recording input and fixes regeneration at exactly 100%• Reverse mode plays memory contents backwards• With an infinite loop locked, knobs or CV can "window" around memory, by shifting the loop• Trigger inputs for toggling Infinite Hold and Reverse• Send and Return for applying effects to feedback with external modules• In stereo mode, Send and Return function as Right Channel Audio Out and In• CV jacks to control Time, Level, Feedback and Dry/Wet MixDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€193.97*
Befaco - Crush Delay
only 1 left
Crush Delay v3 is a special Echo-Delay unit based on the PT2399 IC, which is able to offer 400ms of clean delay and up to 2 seconds of dirty repetitions, having a special talent to generate noisy-glitch textures. This third version comes with some interesting new features like redesigned VCAs circuits, wider range for clean delay and reduced depth to make it skiff friendly.• The module has two inputs (In and Return) that go to the Delay circuit through a dedicated VCA for each one. The main difference between both inputs is the signal fed into In is going to the Dry/Wet circuit also, not only to the Delay, allowing you to control the balance between the original and the processed signal present at the main output (Out).• The signal is processed by the Delay circuit, which is affected by the Crush section. It degrades the signal at slow rates in different ways, depending on the position of the three Crush switches or by the presence of gate signals at the Crush inputs.• After being processed, the signal is routed to three different paths. The first one goes into Dry/Wet, where it’s mixed with the original input signal (In) before going to the main output (Out). The second one is returned to the Delay circuit through another VCA (Feedback), controlling the number of repetitions of the wet signal. Finally, the last one goes directly to the Send output.Features:• Input signal controlled by VCA’s• Bigger range of clean delay• Three different Crush Modifiers based on circuit bending techniques.• VC Feedback wit automatic gain controlDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€147.56*
Befaco - FX Boy
available
A Multi FX module based on game carts!Fx Boy is a multi-FX module designed in collaboration with several talented manufacturers. This is an effect unit with CV control over the parameters and dry/wet control, with a Built-in CV controllable four bands EQ.Each effect is physically hosted in a hot-swappable game cart and designed by a different manufacturer: Touell Skouarn with Skuara a harsh fuzz with overdrive, Instruo with micro Phaser, a two-flavoured Phaser, Feedback modules with a vintage Flanger, XOR with FX-Girl, a digital double effect module: Delay + Granularizer, Making sound machines with an analog Wave folder, Tesseract with a bit crusher and Befaco Trash distortion!Please note that the cards add current consumption on top of the values stated here.Features:• CV control over all parameters and dry/wet• CV controllable four-band EQ, routable post or pre-effect.• Selector for two different flavours of each cart.• Open specifications to design your own carts• Hot swap for all carts. (A tiny pop can occur depending on the cartridge design)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€359.00*
Frequency Central - Stasis Leak
available
DSP based stereo chorus/tap delay/plate reverb module. Stasis Leak is a 6 HP 48kHz DSP effects module, providing a choice of stereo chorus, stereo plate reverb and tap tempo delay. Stasis Leak is based around a Belton ABE-FX sub board, which in turn is based around a Coolaudio V1000 chip.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€102.00*
Hex Haus - HEX lag
available
Hex lag is a digital sound processing instrument with signal modulating potentiometers and an interactive tactile surface for direct sound control. It digitally simulates analogue bucket brigade delay chips (typical of chorus, flanger and karplus-strong), but also enables pitch-shifting, downsampling, etc.Features:• Touch pads• Gain• Rate• Spread• Feed• Push button• Header pins• 3,5 mm input• 3,5 mm output• USB C power portDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€97.37*
Hexdevices - Teko
sold out at the moment
Teko is a tape echo simulator with a wide delay range from 30ms up to 1s. Perfect for clean but also distorted delay effects. The circuit consists a hi – cut filter tuned for deep sounding tape simulation. There’s two outputs, one is the direct delayed signal and the other is a mix of the delayed signal with the original. A CV input is available to control the delay time.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€89.00*
Neutral Labs - Elmyra 2 (Euro)
available
This is the Eurorack version of Elmyra 2, it is available in black and white. Elmyra 2 is a 4-voice digital/analog hybrid platform for microtonal sonic exploration, capable of creating anything from lush ambient soundscapes to gritty droning textures and shrieking noises, available as a 42 HP Eurorack module or semi-modular desktop synth. With 31 modulation targets, 4 polymetric sequencers, delay, additional per-voice effects, a choice of various filters, as well as onboard LFOs and utilities, it is essentially a purpose-built small modular system in itself. A set of preset cards (included) or electronic components like capacitors or diodes can be plugged into the front panel in order to change the sound character.Features:• 4 independent voices activated by touch or CV• wavetable-based complex oscillator engine, up to 12 oscillators in total, 1V/octave compatible• chromatic mode makes chords and harmonic sounds possible, microtonal scales supported• 41 patch points• 31 modulation targets• touchpads with analog envelopes that can be used as modulation sources• resonant filter switchable between:• boomy and aggressive multimode 2-pole state variable filter (low-pass, band-pass, high-pass)• creamy 4-pole low-pass ladder filter• delay with unhealthy amounts of feedback• lo-fi reverb• analog OUCH circuit: a unique combination of destructive distortion, waveshaping and filtering• sonic character can be customised by using special preset cards (set of 4 included) or components like diodes that can be plugged into the front panel• preset cards can be used with other Neutral Labs modules• external audio can be processed via audio input• 9 per-voice modulations and effects:• unison detune• dual sub-oscillators• saturation• bitmangler• sample rate reduction• noise• high-pass filter• low-pass filter• 2 LFOs: 1 sine, 1 complex morphable• 4 sequencers with arbitrary step length per voice (up to 128), allows polymetric structures• delay time and LFOs can be clock-synced or unsynced (tap tempo is also possible)• utilities• dual attenuator/buffered multiple/voltage generator• CV summing circuit• case made of plant-based bioplastic and native German oakwood• boutique synth handmade in GermanyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€329.00*
Neutral Labs - Elmyra 2 (Standalone)
available
This is the standalone version of Elmyra 2, it is available in black and white. Elmyra 2 is a 4-voice digital/analog hybrid platform for microtonal sonic exploration, capable of creating anything from lush ambient soundscapes to gritty droning textures and shrieking noises, available as a 42 HP Eurorack module or semi-modular desktop synth. With 31 modulation targets, 4 polymetric sequencers, delay, additional per-voice effects, a choice of various filters, as well as onboard LFOs and utilities, it is essentially a purpose-built small modular system in itself. A set of preset cards (included) or electronic components like capacitors or diodes can be plugged into the front panel in order to change the sound character.Features:• 4 independent voices activated by touch or CV• wavetable-based complex oscillator engine, up to 12 oscillators in total, 1V/octave compatible• chromatic mode makes chords and harmonic sounds possible, microtonal scales supported• 41 patch points• 31 modulation targets• touchpads with analog envelopes that can be used as modulation sources• resonant filter switchable between:• boomy and aggressive multimode 2-pole state variable filter (low-pass, band-pass, high-pass)• creamy 4-pole low-pass ladder filter• delay with unhealthy amounts of feedback• lo-fi reverb• analog OUCH circuit: a unique combination of destructive distortion, waveshaping and filtering• sonic character can be customised by using special preset cards (set of 4 included) or components like diodes that can be plugged into the front panel• preset cards can be used with other Neutral Labs modules• external audio can be processed via audio input• 9 per-voice modulations and effects:• unison detune• dual sub-oscillators• saturation• bitmangler• sample rate reduction• noise• high-pass filter• low-pass filter• 2 LFOs: 1 sine, 1 complex morphable• 4 sequencers with arbitrary step length per voice (up to 128), allows polymetric structures• delay time and LFOs can be clock-synced or unsynced (tap tempo is also possible)• utilities• dual attenuator/buffered multiple/voltage generator• CV summing circuit• case made of plant-based bioplastic and native German oakwood• boutique synth handmade in GermanyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€379.00*