333modules - Atteo
only 2 left
Quadruple attenuator with offset.Features:• +/- 10V DC Offset• Cascade inputDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€101.15*
ADDAC System - 216 Sum & Difference
available
There are two equal sections in this module labeled A and B.This module is a peculiar type of mixer that instead of just summing two input signals (X & Y), it also allows the possibility to subtract the two signals.It works both for audio and CV signals and hence allows for the possibility to get the diference of two CVs or cancel the phase of two audio signals. The resulting signal, of sum or subtraction, is then routed through a switchable (on/off) full rectification circuit labeled: Absolute. After this the gain of the mixed signal goes through another attenuverter labeled: Amplitude to control the resulting signal gain which, being an attenuverter, also allows the possibility to invert the incoming signal. After the Amplitude comes an AC/DC coupling switch followed by an bipolar Offset knob.Besides the normal output there’s also an inverted output for each of the A & B sections.The outputs of section A & B are also summed and sent to the Average Output.Using a single input, just the X or Y input, the module can also be used as a simple dual Attenuverter & Offset CV processor with full rectification and AC coupling options.Features:• 2 independent sections each with:• 2 inputs with gain attenuverters• Amplitude attenuverter and bipolar Offset• Absolute/Bipolar and AC/DC switches• Output and inverted output• 2 leds monitor the Output polarities and gain.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€130.90*
ADDAC System - 218 Attenuverters
available
Another addition to ADDAC200’s CV Utilities. This module features 3 independent Attenuverters each with its input, output and 13mm knob. White areas allow the user to write down what is connected to each channel.Channel 1 is normalled to Channels 2 and 3.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€80.00*
New
ADDAC System - 309 CV To Expression
sold out at the moment
ADDAC309 CV to Expression allows a simple and straight forward connection between modular and effect pedals that features expression pedal TRS inputs.Instead of using an expression pedal into the effects pedal the user can use this module in between a CV source and the effects pedal to be controlled. This is a great way to control the available parameters on the effects pedals straight from a CV source.ADDAC309 features 2 channels each with a CV input with attenuator and a 1/4" jack output.This is a passive module, the power needed for operation is taken from the pedal power instead of the modular frame, this allows for perfect matching of the pedal’s operating voltage which can range from 3,3 V to 9 V.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€49.00*
ADDAC System - 703 Discrete Mixer
only 2 left
Here's the second module of our 700's Heritage Series.Inspired by Moog CP3 mixer, this is a totally discrete analog mixer and it's not, by any means, your standard breakfast mixer, although it can behave like one.This is a wolf in sheep's clothing. Despite its harmless looks there's a dark snarly soul behind that panel that wants to take your sounds into a realm of gritty, gnarly growls.Features:• 4 Independent channels with input jack and volume knob• 1 Feedback/gate knob• Master output volume knob• 6 Front panel trimmers allows user to adjust the Input resistor trimmer for each channel, feedback and master output• 1 Front panel trimmer allows to adjust the mix BiasDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€107.00*
ADDAC System - 713 Stereo Discrete Mixer
only 2 left
ADDAC713 is the stereo version of our 703 Discrete Mixer. Inspired by Moog’s CP3 mixer, this is a fully discrete analog mixer and it's not, by any means, your standard breakfast mixer, although it can behave like one.This is a wolf in sheep's clothing. Despite its harmless looks there's a dark snarly soul behind that panel that wants to take your sounds into a realm of gritty gnarly growls.This new version was initially thought of as a percussion mixer, with mono inputs and panning, to allow placing percussive voices in the stereo field, while keeping channel 4 in mono for low end sources like a kick drum or Bass. In the development process we slightly changed this initial idea, adding stereo inputs for the first 3 channels, but still kept the 4th channel in mono.All four [GAIN] controls go to extreme levels, the first 3 channels also feature [PAN] controls.Feedback is used to overdrive the whole mix. As the control is turned clockwise the sound will be clipped harder until it goes completely off, this happens as feedback is increased the audio bias reference also moves up, at extreme levels it offsets the whole signal upwards until it completely goes above the top rail clipping the whole signal hence the resulting gate effect.The [MASTER OUTPUT] sets the overall output gain of the mixer, the two LEDs monitor the audio output signal.The soft clipping switch engages an anti-click circuit which adds a low pass before the output, the switch allows 3 states: Soft low pass / Off / Hard low passFeatures:• Three channels with stereo inputs, gain and pan knob• One channel with mono input and gain knob• Feedback/gate knob• Master output volume knob• Soft clipping switchDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€137.50*
ADDAC System - 805 VC Signal Router V2
available
Inspired by our ADDAC701 VCO waveform mixing section, our new VC Signal Router also updates our legacy X-Fade/Panner to a stereo configuration that also allows 4 quadrant mixing.Featuring two dedicated X-faders and a stereo VCA that can also be used as a third X-Fader. All controls have their own CV inputs and dedicated Attenuverters for precision control.4 quadrant mixing is achieved by using the stereo Master as a X-fader between left and right channels, this way you can plug 4 audio sources and sweep/crossfade between each and any of them using the 3 x-faders. Plug any 4 sources (4 waveforms of a VCO, 4 LFOs, 4 envelopes...) and sweep through morph through or have them all mixed together.For other configuration types Left and Right X-fader channels can be routed through the Master stereo VCA or sent directly to the outputs. A stereo Direct input can also be routed through the Master VCA or sent straight to the outputs.The Mono Sum output always mix Left and Right outputs together allowing the possibility to use the module as a peculiar 6 channel mono mixer.It can be used for both Audio or CV Signals.Features:• 6 mono inputs• 2 dedicated X-faders with Control knob + CV Input and Attenuverter Each X-fader can be routed through the Master mix or straight into the outputs.• Master channel can be used as a stereo VCA or an X-fader• Stereo direct inputs can be routed through the Master mix or straight into the outputs.• Fully analog audio path with high quality/low noise VCAs.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€168.90*
New
AtoVproject - MMx2
available
Expand the power of your modulations with the MMx2, a dual-pack module designed to bring flexibility and creativity into your system. Each MMx2 package contains a pair of MM modules.Sold as a pair, MM modules can function as two separate units or be linked for expanded matrix mixing capabilities. Connect even more MM modules to increase the power of your Eurorack synthesiser!Every MM module has attenuator on the first two inputs and attenuverters on the last two and the MM modules amplify the mixed output by 2.The MMx2 merges essential utilities into one powerful package, offering a CV mixer, attenuverters, signal amplification, offset generator, and a multiple, all in a compact form. Ideal for distributing modulations, creating complex mixers, generating stereo effects, and much more.The MMx2 is a testament to AtoVproject's dedication to creating instruments that allow you to express yourself and reward your understanding and exploration. To facilitate this, the MMx2 comes with a detailed manual full of inspirational patch ideas that will take your sound design to the next level.Dive into the world of advanced modulation manipulation with MMx2.Stay inspired! Stay innovative!Features:• Sold as a pair• 4 in 1 DC Mixer• Multiple MMs can be combined into a matrix mixer• Optimized for CV - Audio compatible• Input 1 and 2 have attenuators• Input 3 and 4 have attenuverters (polarizers)• Input 1 to 3 can be chained to the next module Input 4 is normalled to a voltage source so it can be used as offset controlDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€160.00*
Befaco - Dual Atenuverter
available
The Dual Atenuverter is a CV/Audio utility module designed to attenuate, invert and apply offset to an input signal.The IN of the first channel is normalled to the IN of the second so it can be used as a two-channel splitter.Features:• The “ATENUVERTER” pot will multiply your signal by 1 when turned clockwise and -1 when turned anti-clockwise.• The “OFFSET” control can add +/- 10V DC to the output. Useful as a manually controlled DC source when no input is connected.• Bicolour LEDs glow red when the output is positive and green when negative meaning this module works well as a CV monitor.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€59.50*
Befaco - Joystick
available
A compact attenuverting (attenuator-inverter) joystick controller and Gate Generator. With it, you can generate and process two control voltages using only one hand. Provided controls for CV ranges and offset adjust the boundaries of your control, this way it never gets out of the desired range, ensuring sensibility and playability even with wild performance gestures.Features:• Robust arcade style joystick for manually generating either CV with Range and Offset control or attenuating two input signals• Two push buttons to generate gates manually.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€113.05*
Befaco - Mixer
available
A four channel mixer, suitable for audio or control signals. It features regular and inverted outputs as well as an LED level meter.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€59.50*
Befaco - ST Mix 1U
available
STMix is a four-channel stereo mixer in 28 HP and 1U format. It can work independently or as an expansion of our Hexmix module via the six-pin connector located in the back. The module is designed under the Intellijel 1U format.Features:• Four channels stereo inputs with volume control.• AC Coupled inputs to improve audio performance.• Output clipping LED indicators.• Connector at the back to interface with the Hexmix module.• 1U Intellijel format.• Pulp Logic Panel format available on demand. Call Befaco.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€70.21*
Befaco - STMix
available
STMix is a compact 4 channel stereo mixer with an auxiliar input. This input will allow us to chain a few of them or to insert an extra fifth input.This module is compatible with our Hexmix System and can be internally connected to the Hexmix module to add the output of STMix to your main mix.Features:• Four channels stereo inputs with volume control• Aux input straight to the Mix out• Input Impedance selector• Level meter LEDs• Connector in the back to interface with Hexmix module.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€76.16*
Befaco / Molten Modular - Motion MTR
available
Motion MTR allow you to mix, attenuate and invert signals while having clear visual feedback of their levels.Each channel can function as:• Audio level control with VU meter• CV attenuator with voltage meter• CV inverter with voltage meterEach input is normalled to 10v, so you can use each of them to generate fixed voltages. Also, the outputs of channels 1 and 2 are summed into Out 3 to be used as a mixer. Patch it wildly to make it work as an attenuverter with offset, as a mixer, a VU meter or a combination of them all!This module is designed in collaboration with Robin Vincent from Molten Modular.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€113.05*
Befaco / Molten Modular - Motion MTR 1U
available
This is the 1U version of the module, for the 3U standard version please check the other product!Motion MTR allow you to mix, attenuate and invert signals while having clear visual feedback of their levels.Each channel can function as:• Audio level control with VU meter• CV attenuator with voltage meter• CV inverter with voltage meterEach input is normalled to 10v, so you can use each of them to generate fixed voltages. Also, the outputs of channels 1, 2 and 3 are summed into Out 4 to be used as a mixPatch it wildly to make it work as an attenuverter with offset, as a mixer, a VU meter or a combination of them all!This module is designed in collaboration with Robin Vincent from Molten Modular.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€121.38*
Black Noise Modular - SAM-C
only 2 left
SAM-C is our first 0 HP module. To introduce this new range we wanted to take advantage of the benefits of passive modules. But we also wanted to incorporate as many features as possible. The result is SAM-C, a small module that takes up no space in your rack and can perform many simple but useful utility functions.SAM-C can be used as Attenuator, Multiple, Mixer and Crossfader.To learn more about SAM-C and discover our patch ideas, feel free to take a look at the manual below.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€25.90*
CubuSynth - 6xLevel
only 1 left
The CubuSynth 6xLevel module is a 8 HP passive attenuator, which allows scaling of CV and audio signals. The inputs are normalized from the outputs above, which allows passive multiplication with attenuation. The normalized path is attenuated by the potentiometer before, so you can also create very subtle changes (e.g. Fine tune a VCO). The silver lines on the front panel mark the normalisation routing.Note, that it is a passive module, for multiplying non-precise voltages. It is recommended to not use more than 3 outputs from the same input.Features:• 6 individual attenuators• flexible passive multiple (1x6, 2x3, 3x2, 1x4 + 1x2)• normalized inputs from output aboveDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€41.00*
Feedback Modules - CP3-
sold out at the moment
THE CP3MINUS is the 6HP SMD variant of CP3+ Mixer, minus the MULTI section.Features:• 4 mono analog input• 4 input level pots• 1 dual level pot• One inverting and one non-inverting output jacks• Standard 10 pin euro power (+12V / -12V)DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€41.65*
Feedback Modules - smArTT Verter
available
The smArTT Verter is a simple but very effective utility module for scaling the level and polarity of audio and CV signals.Features:• 1 audio/CV input• 1 input level potentiometer• 1 signal polarity switch (+/-)• 1 DC offset potentiometer (+/-5V or +/-10V)• 3 output jacksDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€27.50*
Jolin - Knobi
only 1 left
Macro ControllerKNOBI is a multi-tool able to mix, attenuate, invert, display and multiply any kind of signal. Knobi can serve a wide range of purposes thanks to its internal signal path that makes use of some of the most useful building blocks of analog synthesis: a 4-channel mixer, a three-range offset, an attenuverter, a fixed manual gate and lastly a cascading multiple derived from the output stage of Agogô.a, b, c and d are Knobi’s inputs while r is a fixed 5v reference output. The toggle switch next to d sets the range of the offset - the big knob below the meter. Connect a signal into one of the inputs to visualize its voltage value in the three digits meter. Keep in mind that this reading happens post offset and attenuverter - the smaller knob with (-) and (+) indications.The pushbutton next to x4 adds a gate of 5v to the mix: with no input connected it will act as a manual gate output. Autopatch the r reference output into one of the inputs to use Knobi as a macro controller thanks the offset knob and switch to set the range and the attenuverter.x1, x2, x3 and x4 are all cascading copies of the final signal path. Plugging a cable will break the normalization and the multiplication will reset starting from the next output. Four cables plugged in will output a copy at the same factor x1 - unity gain - making Knobi a versatile buffered multiple.Features:• Thermally compensated 5v voltage source with dedicated output.• Four channel mixer with four buffered output.• Built in 3 digits voltage meter post mix / attenuation / inversion.• Offset with a dedicated three positions range toggle.• Manual gate button tied to the mix.• 4 cascading outputs in an open design configuration.• Unique signal path: mix - attenuate - invert - add - visualize - multiplicate.• “Whatever” power connector a.k.a. don’t mind the polarity.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€153.51*