ADDAC System - 213A Eurorack Bridge
available
The first modules from our Eurorack Bridge system!A pair of ADDAC213As acts as a simple one-cable bridge between different cases. By itself the ADDAC213As can send/receive 8 CV or audio signals between your cases, but can be expanded to bridge two cases for up to 24 signals at the same time.Use a pair of ADDAC213As to send & receive 8 CV or audio signals between distant points in your case, between two separate cases, or between your case and a friend's case. Less clutter, less spaghetti, faster connection! There’s nothing better than being able to connect that controller skiff with just one cable to your main system. At a gig, in the studio, when jamming with a friend, give yourself a gift by grabbing a pair of ADDAC213As. The modules can be installed in normal position or a 180 degree position to fit any need and any case design.Expansion by the ADDAC213BsEach ADDAC213A module can be connected through a ribbon cable connection on its backside with up to two ADDAC213Bs. Each ADDAC213B module added expands the channels options of the ADDAC213A by adding 8 more channels. With two ADDAC213Bs connected to each ADDAC213A module, you’ll have a total of 24 channels going between your cases with a simple one-cable bridge. Between the ADDAC213A pair and the ADDAC213B, your cases never looked so elegantly connected together!The ADDAC213As are always sold as a pair of 2 modules and an included ribbon cable (50cm or 100cm ribbon cable, or custom sizes available upon request).Each module can be installed in normal position or at 180 degrees.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€95.00*
ADDAC System - 213B Eurorack Bridge EXP
only 1 left
The ADDAC213B is the second pair of modules from our Eurorack Bridge system!A pair of ADDAC213Bs can be used in standalone to send/receive 8 CV or audio signals between different points inside the same case or as an expansion to the main pair of Eurorack Bridge modules, the ADDAC213As.Standalone use:Two ADDAC213B modules can be connected to each other with the use of a single ribbon cable and then used inside a case to carry signals between distant points without the need for long cables. Less clutter, less spaghetti, more space of your fingers on those knobs!ADDAC213Bs always come in pairs. A single pair can send & receive up to 8 CV or audio signals between different points in your case at the same time. The modules can be installed in normal position or a 180 degree position to fit any need.Do you have modules that you often use together in different areas of your case? Would you prefer that each row’s cables don’t mingle with cables from other rows? Grab yourself a pair of ADDAC213s.As an Expansion to an ADDAC213A:Each ADDAC213B connected to the backside of an ADDAC213A adds 8 more channels to the main bridging functionality of the ADDAC213A.Up to 2 ADDAC213B can be connected to an ADDAC213A module, expanding the bridging between two difference cases to a total of 24 channels.If you’re looking for a simple one-cable bridge between your various cases, then look no further than the ADDAC213A.Between the ADDAC213A pair and the ADDAC213B, your cases never looked so elegantly connected together!Each module can be installed in normal position or at 180 degrees.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€80.00*
ADDAC System - 213C Eurorack Bridge (1U)
only 2 left
The ADDAC213C is the third pair of modules from our Eurorack Bridge system, this time made for 1U rack rows!A pair of ADDAC213Cs can be used in standalone to send/receive 8 CV or audio signals between different points inside the same case or as an expansion to the main pair of Eurorack Bridge modules, the ADDAC213As.Standalone use:Two ADDAC213C modules can be connected to each other with the use of a single ribbon cable and then used inside a case to carry signals between distant points without the need for long cables. Less clutter, less spaghetti, more space of your fingers on those knobs!ADDAC213Cs always come in pairs. A single pair can send & receive up to 8 CV or audio signals between different points in your case at the same time.Do you have modules that you often use together in different areas of your case? Would you prefer that each row’s cables don’t mingle with cables from other rows? Grab yourself a pair of ADDAC213s.As an Expansion to an ADDAC213A:Each ADDAC213C connected to the backside of an ADDAC213A adds 8 more channels to the main bridging functionality of the ADDAC213A.Up to 2 ADDAC213C can be connected to an ADDAC213A module, expanding the bridging between two difference cases to a total of 24 channels.If you’re looking for a simple one-cable bridge between your various cases, then look no further than the ADDAC213A. Between the ADDAC213A pair and the ADDAC213B, your cases never looked so elegantly connected together!Price is for a pair of modules (2 modules) including two 50cm ribbon cables; only one is used to connect the two ADDAC213C together but two are necessary when connecting the two ADDAC213C to two ADDAC213A. Custom ribbon cable sizes also available upon request, ask ADDAC.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€80.00*
AI Synthesis - Matrix Mixer
available
The AI008 Matrix Mixer is an active, four in, three out matrix mixer with a summed output. The AI008 can be used to route any of the inputs to any of the outputs. This allows for the creation of feedback patches and other interesting routing, in addition to powerful "regular" signal routing. Common uses include mixing effects outputs into their inputs in order to create drones (or just good old fashioned feedback), mixing oscillators into their own PWM or FM inputs, modulating voltage controlled LFOs and other modulators into themselves, and other feedback patches. The AI008 Matrix mixes is a powerful way to expand any system!DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€107.00*
AtoVproject - MMx2
available
Expand the power of your modulations with the MMx2, a dual-pack module designed to bring flexibility and creativity into your system. Each MMx2 package contains a pair of MM modules.Sold as a pair, MM modules can function as two separate units or be linked for expanded matrix mixing capabilities. Connect even more MM modules to increase the power of your Eurorack synthesiser!Every MM module has attenuator on the first two inputs and attenuverters on the last two and the MM modules amplify the mixed output by 2.The MMx2 merges essential utilities into one powerful package, offering a CV mixer, attenuverters, signal amplification, offset generator, and a multiple, all in a compact form. Ideal for distributing modulations, creating complex mixers, generating stereo effects, and much more.The MMx2 is a testament to AtoVproject's dedication to creating instruments that allow you to express yourself and reward your understanding and exploration. To facilitate this, the MMx2 comes with a detailed manual full of inspirational patch ideas that will take your sound design to the next level.Dive into the world of advanced modulation manipulation with MMx2.Stay inspired! Stay innovative!Features:• Sold as a pair• 4 in 1 DC Mixer• Multiple MMs can be combined into a matrix mixer• Optimized for CV - Audio compatible• Input 1 and 2 have attenuators• Input 3 and 4 have attenuverters (polarizers)• Input 1 to 3 can be chained to the next module Input 4 is normalled to a voltage source so it can be used as offset controlDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€160.00*
Befaco / Molten Modular - Molten Bypass
available
This is our new collaboration with Robin Vincent aka Molten Music Technology. A Stereo bypass module to gate control the send of your signals to your favorite effect!Molten bypass features a hard/soft bypass control, to hard cut the return of your effect or allow the long tails of your reverb to stay after you bypass the effect. Also a gate/latch control to use either triggers or gates for control and a gain control for the returned signal.Features:• Full stereo signal path• DC coupled• Hard or soft bypass selection• Gate or Latch possibility• Manual or Gate control• Gain control over the returnDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€100.00*
Black Noise Modular - Pipe
sold out at the moment
Now introducing PIPE in our sleek Black & Gold theme, featuring a reversible faceplate. Feel like installing your PIPE upside down? No worries – just unscrew the 8 jnuts, flip the faceplate, and put everything back together and Voila! You can now use your PIPE with the connector facing down!With the ability to connect up to 8 inputs or outputs via an ethernet cable, the PIPE-S makes it easy to connect multiple cases together or avoid any cable mess accross a case. This makes it the perfect solution for simply setting up your Eurorack system in the studio or a live gig.But that's not all, PIPE can also be used as a multiple passive 3 section. Want to transmit precise signals like pitch CV and want to avoid crosstalk induced by passive multiples? No worries you can easily deactivate this function for each section from the connector at the back of the module.The best part is that PIPE is completely passive which means you can place it anywhere, it doesn't draw any current from your power supply, which perhaps makes it the simplest DIY module!PIPE modules are sold by pair.The ethernet cable is not supplied with the modulesRegarding Ethernet cableWe recommend shielded Straight-Thru RJ45 cable.Using un-shielded or Crossover cable won't damage your modules but you may experience noise and or mixed channels.Due to its passive nature we also recommend to avoid long ethernet cables.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€92.00*
Black Noise Modular - Pipe - S
only 1 left
With the ability to connect up to 8 inputs or outputs via an ethernet cable, the PIPE-S makes it easy to connect multiple case together or avoid any cable mess accross a case. This makes it the perfect solution for simply setting up your Eurorack system in the studio or a live gig.But that's not all, PIPE-S can also be used as a multiple passive 3 section. Want to transmit precise signals like pitch CV and want to avoid crosstalk induced by passive multiples? No worries you can easily deactivate this function for each section from the connector at the back of the module.The best part is that PIPE-S is completely passive which means you can place it anywhere, it doesn't draw any current from your power supply, which perhaps makes it the simplest DIY module!PIPE-S modules are sold in pairs.The ethernet cable is not supplied with the modulesRegarding Ethernet cableWe recommend shielded Straight-Thru RJ45 cable.Using un-shielded or Crossover cable won't damage your modules but you may experience noise and or mixed channels.Due to its passive nature we also recommend to avoid long ethernet cables.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€70.00*
Frequency Central - Looking Glass
sold out at the moment
Looking Glass is an 5 x 5 active patchbay/matrix mixer/switcher for both audio and control voltages.Features:• 5 inputs (1 through to 5), each with attenuators• 5 inverted outputs (A through to E) which are 180o out of phase with the inputs• 5 normal outputs (A through to E) which are in phase with the inputs• A switch matrix of 25 push on/push off switches and LED status indicatorsDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€76.00*
Frequency Central - Wonderland
sold out at the moment
Wonderland is an 8×8 active patchbay/matrix mixer/switcher for both audio and control voltages.Any of the 8 inputs can be patched to any of the 8 outputs simply by pressing the corresponding switches. A patched signal will appear at both normal and inverted outputs simultaneously.A single input can be patched to a single output. A single input can be patched to multiple outputs. Multiple inputs can be patched to a single output. Multiple inputs can be patched to multiple outputs.Each input features a micro-attenuator which can be set with a small screwdriver. This space saving feature allows you to reduce the volume of an incoming signal without having to resort to external attenuators. If you add many inputs to one output you will of course cause clipping (which may or may not be desirable!), the micro-attenuators are your on-board way around this. I find it useful to leave the micro-attenuators set to 50% (which is how they come pre-set at delivery). Of course, their size is a little bit of a compromise, but they are a useful feature nonetheless. Wonderland’s sister module Looking Glass includes full size input attenuators as well as LED status indicators.Features:• 8 inputs (1 through to 8), each with micro-attenuators (which can be set with a small screwdriver)• 8 buffered inverted outputs (A through to H) which are 180o out of phase with the inputs• 8 buffered normal outputs (A through to H) which are in phase with the inputs• A switch matrix of 64 push on/push off switchesDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€130.00*
Jolin – Rosa
available
ROSA is a multi-mode crossfader, scanner, and switcher that allows seamless morphing between up to four inputs and outputs. With its three operating modes (Scan, Wave, and Pass), you can easily shape and route signals to fit any patch.Features:• Scan Mode: Morph between up to four inputs with adjustable curves using the KNEE control.• Wave Mode: Independently control the four VCAs for complex dynamic changes.• Pass Mode: Route a single input (or mix multiple inputs) to up to four outputs, perfect for quadraphonic setups or parallel processing.• Infinite Analogue Potentiometer: For smooth, continuous transitions.• Global SHUT Control: CV-controlled mute for immediate silence.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€222.00*