DIY Kits
only 2 left
Midiphy - Wirescanner is a compact DIY cable tester designed to quickly validate IDC and MicroMatch ribbon cables used in Eurorack, MIDIbox and midiphy hardware builds. Instead of guessing where a cable fault might be, the Wirescanner displays the connection pattern graphically on a 16 × 16 LED matrix, making continuity errors, wrong pin mappings or faulty ribbon cables easy to spot at a glance.The tool is especially useful when building or servicing complex DIY projects such as the midiphy SEQ v4+, MatriX or other systems using internal ribbon connections. It supports IDC 8/10/16 and MicroMatch 8/10 cables, covering common Eurorack power cables as well as many internal data connections found in synth and DIY electronics projects.Built without a microprocessor, Wirescanner offers a direct and practical testing workflow: connect the cable, check the LED pattern and confirm whether the wiring is correct. A clean diagonal line indicates a properly wired straight cable, while deviations immediately reveal crossed, missing or problematic connections.The full kit includes the necessary parts and enclosure, making it a useful workshop tool for DIY builders, modular technicians and anyone assembling ribbon cables by hand. Small, visual and easy to use, the midiphy Wirescanner helps prevent hard-to-trace build errors before they become bigger problems.Features:• DIY cable tester for IDC and MicroMatch ribbon cables.• Supports IDC 8/10/16 and MicroMatch 8/10 connections.• Graphical 16 × 16 LED matrix for visual cable validation.• Useful for Eurorack power cables and internal synth DIY wiring.• Helps detect crossed, missing or faulty cable connections.• No microprocessor required.• Full kit includes all parts and enclosure.• Practical tool for midiphy SEQ v4+, MatriX and MIDIbox builds.• Suitable for DIY builders, repair benches and modular workshops.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
available
Quadruple LFO with four triangle outputs and four square output, swith with range selector for oscillations audio frequencies.Features:• 4 x LFOs• LFO and audio frequencies• Triangle and square outputsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Anti Logic combines two gate signals using AND, OR and exclusive OR logic, with inverted versions of all three functions. Use the six logic operations to derive new gate patterns from existing signals in your Eurorack patch.Features:• AND, OR and XOR logic• Inverted NAND, NOR and XNOR functions• Two-input logical operationsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Quadruple attenuator with offset.Features:• +/- 10V DC Offset• Cascade inputDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Clock Divider provides an internal clock, a reset function and clock divisions from 2 to 512. Use it to derive slower timing signals and coordinate different parts of a rhythmic Eurorack patch.Features:• Internal clock• Clock divisions from 2 to 512• Reset functionDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
4 LFOs, triangle and square outputs per channel and CV input and pot for modulation.Features:• 4 x LFOs• Triangle and square outputs per channel• CV input per channelDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Four decay envelopes with CV.Features:• 7 V peak output• Release: Aprox. 1 ms to 3 min.• Cascade trigger input• CV per channelDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
• 2x ASR• LFO loop mode (150Hz - 3sec)• 7,5V peak output• Cascade trigger inputDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Dual FM OSC combines two oscillators with square and triangle waveforms, frequency modulation inputs and a summed mix output. It provides a compact starting point for FM experiments and layered oscillator patches.Features:• Two oscillators• Square and triangle waveforms• FM inputs• Summed mix outputDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Two channel LFO with Triangle and Square outputs. The frequency range selector allows you to use it at audio frequencies. Each channel counts with an additional Sample and Hold circuit which can be synchronize with your own signals thanks to its dedicated Trigger and S&H Inputs.Features:• 2 x LFO output (triangle and square)• 2 x Sample and hold output (+/- 5V auto generated by LFOs in disconnection)• Trigger and S&H in inputs• LFO selector (lfo or audio speed)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Double delay effect module based on two PT2399 chips mounted in series, noise and glitchy module with 4 different feedback points (2 pre-PT and 2 post-PT) and voltage controlled delay time.Features:• Two PT2399 chips in series• 4 x feedback pots• 2 x voltage controlled delay time• Dry / Wet• Trash, noise and glitchyDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Envelope follower with preamp, level and 2 outs: Gate out, envelope out.Features:• Fine pot to adjust levels• Gate out, envelope outDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Analog FM percussion generator. Selectable Triangle and Square waveform for both, Modulator and Carrier VCO’s Onboard VCA with CV controlled Decay envelope. Perfect for harsh sounds and timbres.Features:• CV for decay envelope and CV for modulation.• VCO (triangle or square) modulated by LFO (triangle or square) and VCA whit decay (pot and CV)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
External IN module to modular level, with L and R output and mono sum.Features:• 6,3 jacks inputs• L,R and mono output to modular levelDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Input module with DJ influence, RCA in and selectable line and phono input (RIA filter), with three modular level outputs Left, Right and Mono sum. Level gain with fader volume for live purposes.Features:• RCA input• Phono (RIA) or line• Gain and fader volumen• Stereo a Mono sum Output modular levelDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
LFO Bi is a dual low-frequency oscillator with skew and pulse-width controls, restart inputs, and triangle and square outputs. Its two ranges cover slow modulation and faster cycles extending into the audio range. The low range runs from one cycle per minute to one cycle per second; the high range runs from a 1.2-second period up to 40 Hz.Features:• Two LFO channels• Triangle and square outputs• Skew and pulse-width controls• Restart inputs• Low range: 60-second to 1-second period• High range: 1.2-second period to 40 HzDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
4x MIDI thrugh with mutes and momentary.Features:• On-off momentary MIDI mutes.• 1 midi IN to 4 midi THRU output.• Also MIDI IN, in back PCB pins.• Another extra MIDI OUT, in back PCB pins.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
MINI VCA packs four voltage-controlled amplifiers into a compact Eurorack module. Based on the 3360 VCA circuit, it provides separate outputs for the four channels, allowing signals to be controlled and routed individually.Features:• Four VCA channels• 3360-based circuit• Individual channel outputsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Mix Tour is a compact four-channel stereo mixer with volume controls and a stereo output. It brings several stereo signals together in a straightforward Eurorack mixing stage.Features:• Four stereo channels• Volume controls• Stereo outputDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Utility module with either buffered multiply and summing sections. 1 In to 8 Out or 2 In to 4 Out operation are selectable at multiply section. On summing section 2 sets of 4 signals can be summed to its related output.Features:• 1 In to 8 Out or 2 In to 4 Output (desconexion).• 2 x 4 signals summed Output.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.