333modules - Dual PT
only 1 left
Double delay effect module based on two PT2399 chips mounted in series, noise and glitchy module with 4 different feedback points (2 pre-PT and 2 post-PT) and voltage controlled delay time.Features:• Two PT2399 chips in series• 4 x feedback pots• 2 x voltage controlled delay time• Dry / Wet• Trash, noise and glitchyDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€136.85*
4ms - Looping Delay
available
Crystal-clear clock-synced delay for loop up to 90 seconds, echoes, sound-on-sound, Karplus-Strong etc.Features:• Loop or echo time is synchronized to a clock• 87 seconds of delay/loop time maximum in mono mode, 43 seconds in stereo mode• 48kHz/24-bit sampling rate, loop recorded at 16-bit (24-bit optional)• Extremely quiet, low noise and low jitter design• Tap tempo button and clock Ping input set the basis for one "beat"• Delay/loop time set as a number of musical beats (or fractions of beats) using the Time knob, switch, and CV jack• Sample-accurate clock output for perfect synchronization• Loop clock output• Time switches change range of Time knob from 1/8th notes up to 32 bars• Digital feedback, up to 110%• Delay Feed control, independent of dry/wet signal mix• Infinite Hold mode disables recording input and fixes regeneration at exactly 100%• Reverse mode plays memory contents backwards• With an infinite loop locked, knobs or CV can "window" around memory, by shifting the loop• Trigger inputs for toggling Infinite Hold and Reverse• Send and Return for applying effects to feedback with external modules• In stereo mode, Send and Return function as Right Channel Audio Out and In• CV jacks to control Time, Level, Feedback and Dry/Wet MixDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€193.97*
4ms - Meta Module (Assembled)
available
The MetaModule puts real knobs and jacks on virtual software modules. Step back from the computer and make music with hardware, while keeping the flexibility and expandability of software.THIS PRODUCT IS ASSEMBLED AND NO DIY!The MetaModule comes with over 160 built-in modules from 4ms Company, Befaco, HetrickCV, NonlinearCircuits, and Scanner Darkly, plus clones of popular classics such as the Mutable Instruments Eurorack modules, fun physical modeling algorithms, and lots of handy utilities.All of the included modules are also available on the computer using the free program VCV Rack. Whether you make patches on VCV Rack and transfer them to the MetaModule, or if you just create patches directly on the MetaModule, there are plenty of creative modules to inspire new ways to make music.MetaModule PluginsIf the 160+ built-in module aren’t enough, you can load more modules as plugins. Already there are over 200 modules in third-party plugins from Bogaudio, Valley, ChowDSP, NANO Modular, and the list is growing. We have an SDK available to make it easy for VCV Rack plugin developers to convert their plugin to a MetaModule plugin. Our licensing terms are non-restrictive: developers are welcome to distribute their plugin in any way they wish, commercially or not.Mapping Knobs and JacksThe MetaModule has 12 knobs that can be mapped to virtual knobs. Each knob can be mapped to up eight virtual knobs, and each mapping can have a different range and offset. You also can save a group of mappings as a Knob Set and switch between Knob Sets with the encoder. You also can map the 8 inputs and 8 outputs to virtual module jacks. Also, the MetaModule is a USB MIDI host, so you also can map MIDI CC, note, gate, and other parameters to knobs and jacks.ExpandersThere are lots of ways to customize your MetaModule. A Wifi expander allows you to wirelessly transfer patches from your computer. Add eight more knobs with the Knob expander, or buttons with the Button expander. A CV/Audio expander adds more high-resolution inputs and outputs, and the Gate In/Out expander adds not only gate jacks but also TRS MIDI and I2C.Under the HoodThere are six CV/Audio inputs, two gate inputs, and six CV/Audio outputs. The CV/Audio jacks are all 24-bit, 48kHz DC-coupled, -10V to +10V. A USB-C jack accepts MIDI devices and thumb drives. Patches and plugins can be loaded via a USB drive or microSD Card, and internal flash memory lets you save patches you always want to come back to.The processor is more advanced than anything 4ms has used in the past, and is among the most powerful processors found in Eurorack. Startup time and latency are blazingly fast.Features:Patches• Patches are loaded from microSD Card, USB drive, or via the Wifi expander• Patches can be optionally saved onto internal flash memory• Create patches using VCV Rack or directly on MetaModule• Patches can be given a name and descriptionMappings• Map each physical knob to up to 8 virtual knobs• Set range and offset for each mapping, including inverted control• Knob mappings are grouped into Knob Sets, and changing Knob Sets can be done quickly without menu-diving• Map physical jacks to virtual jacks, seamlessly making splits/mults• Add or edit modules, cables, and mappings in real-time while the patch is playing• Create alias names for mappings like "Kick Drum Level"Interface• Simple, intuitive graphical interface lets you zoom in on details, or zoom out to get a big picture• Patch View displays the patch as faceplates and cables, with knobs, buttons, and lights animating in real-time• Knob Set View simplifies the display, showing only the mapped knobs for the current Knob Set• Module View shows just one module and lists the names of each jack, knob, and control legibly• Mapping View lets you adjust details of a knob mapping• Adjust styles and visual preferences to your liking• Save, rename, duplicate, and delete patches• Firmware updater and plugin loader read from microSD Card or USB driveHardware• 12 Knobs• 8 CV/Audio outputs, 24-bit 48kHz, -10V to +10V, DC-coupled• 6 CV/Audio inputs, 24-bit 48kHz, -10V to +10V, DC-coupled• 2 Gate inputs• USB-C jack: MIDI Host or MSC (External drive) Host• microSD Card slot• Internal Flash RAM for additional patch storage• Dual-core 800MHz Cortex-A7 plus Cortex-M4 co-processor• 512MB DDR3 533MHz RAM• Bare-metal operation for fast startup and low latencyDIY-Kit-Type:Assembled unit. This is completely ready to use, nothing to solder or to assemble.
€649.00*
ADDAC System - 703 Discrete Mixer
sold out at the moment
Here's the second module of our 700's Heritage Series.Inspired by Moog CP3 mixer, this is a totally discrete analog mixer and it's not, by any means, your standard breakfast mixer, although it can behave like one.This is a wolf in sheep's clothing. Despite its harmless looks there's a dark snarly soul behind that panel that wants to take your sounds into a realm of gritty, gnarly growls.Features:• 4 Independent channels with input jack and volume knob• 1 Feedback/gate knob• Master output volume knob• 6 Front panel trimmers allows user to adjust the Input resistor trimmer for each channel, feedback and master output• 1 Front panel trimmer allows to adjust the mix BiasDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€107.00*
ADDAC System - 705 VC Stinggy Filter
sold out at the moment
Here's our new filter inspired by the original WASP Filter.Features:• Four diferent filter types: Low-Pass, Band-Pass, Notch-Pass and High-Pass with independent audio outputs.• Cutoff features a voltage-controlled cv input with a dedicated cv attenuator pot.• Two switches selects different Resonance clipping paths: no clipping / diodes and Resonance depth: high / low.• The Main output filter type can be selected through a 4 position switch.• The Main output circuit features a Distortion/Fuzz circuit that adds extra harmonics to the filtered audio.• Phase switch selects the Main output phase polarity.• One Led monitors the audio signal of the main output.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€119.00*
ADDAC System - 712 Vintage Pre
available
ADDAC712 is a dual channel discrete gain staging amplifier, based on a famous discrete preamp board from the 70’s used in some legendary equipment. What caught our attention was the character of it’s clipping and resulting saturation/distortion.The module can be used with modular signals to add a distortion/fuzz character or as a preamp for an external source such as a line source, keyboard, guitar... It’s also a great side companion for our ADDAC711 Balanced Inputs.At the top an On/Off [BYPASS] switch routes the signal into the Effect (Up: Active) or to the bottom output gain stage (Down: Bypassed).The amount of amplification is set by the [GAIN] control, the maximum amount of amplification can be set by the user using the [MAX GAIN] trimmer.Up to ±5,5v the incoming signal will keep it’s integrity, beyond this point saturation will start to increase. At approx. ±6v a hard clipping will start to occur, this clipping also has a particular quality that at extreme levels it drifts the audio 0v bias reference, moving it upwards which results are similar to a Gate effect.In the middle, an x2 op-amp based output gain stage with a clipping LED, which monitors the clipping at the output, and an [OUTPUT] control to set the output volume.Having the top and middle gain stages provides flexibility allowing the user to completely distort the signal on the top stage and tame it’s output level with the second stage.At the bottom, input and output for both channels (left input is normalled into right input).DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€105.90*
ADDAC System - 713 Stereo Discrete Mixer
sold out at the moment
ADDAC713 is the stereo version of our 703 Discrete Mixer. Inspired by Moog’s CP3 mixer, this is a fully discrete analog mixer and it's not, by any means, your standard breakfast mixer, although it can behave like one.This is a wolf in sheep's clothing. Despite its harmless looks there's a dark snarly soul behind that panel that wants to take your sounds into a realm of gritty gnarly growls.This new version was initially thought of as a percussion mixer, with mono inputs and panning, to allow placing percussive voices in the stereo field, while keeping channel 4 in mono for low end sources like a kick drum or Bass. In the development process we slightly changed this initial idea, adding stereo inputs for the first 3 channels, but still kept the 4th channel in mono.All four [GAIN] controls go to extreme levels, the first 3 channels also feature [PAN] controls.Feedback is used to overdrive the whole mix. As the control is turned clockwise the sound will be clipped harder until it goes completely off, this happens as feedback is increased the audio bias reference also moves up, at extreme levels it offsets the whole signal upwards until it completely goes above the top rail clipping the whole signal hence the resulting gate effect.The [MASTER OUTPUT] sets the overall output gain of the mixer, the two LEDs monitor the audio output signal.The soft clipping switch engages an anti-click circuit which adds a low pass before the output, the switch allows 3 states: Soft low pass / Off / Hard low passFeatures:• Three channels with stereo inputs, gain and pan knob• One channel with mono input and gain knob• Feedback/gate knob• Master output volume knob• Soft clipping switchDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€137.50*
ADDAC System - 714 Vintage Clip
only 1 left
ADDAC714 is a dual channel soft clipping module.Diode based passive clipping acts as a “brick wall” limiter with a fixed knee given by the inherent diode physics. A passive RC low pass circuit adds a 3,3KHz -3db low pass filter which sculpts the overall tone while also adding further character to the effect.At the top an On/Off [BYPASS] switch routes the signal into the Effect (Up: Active) or to the bottom output gain stage (Down: Bypassed).The amount of clipping is set by the [GAIN] control, it mostly works as a threshold control for how much clipping will be applied. As more clipping is applied the signal’s amplitude will also decrease, to compensate for this we set up a gain compensation stage to keep the output amplitude balanced across the Gain range.Symmetry chooses between bipolar clipping or positive clipping, this relates to the harmonics generated, bipolar for odd and even harmonics (up position) and unipolar for odd harmonics only (down position).At the second stage, an op-amp based x2 output gain with a clipping led, which monitors the clipping at the output, and an [Output] control to set the output volume.Having the top and middle gain stages provides flexibility allowing the user to completely distort the signal on the top stage and tame it’s output level with the second stage.At the bottom, Input jacks for both channels (Left input is normalled into Right input) and output jacksDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€100.00*
AF Labs - MI Blades (PCB)
available
Features:• An essential overdrive circuit A CV-controlled overdrive stage precedes each of the two filters. Overdrive response continuously adjustable between soft-clipping and 2-stage wavefolding.• Two rich multimode filters Clean 2-pole (12dB/octave) state-variable design. CV-controlled filter response, continuously variable between low-pass, band-pass and high-pass. CV inputs with attenuverters for cutoff and resonance. Unattenuated frequency CV input, calibrated for 1V/Oct tracking. Clean self-oscillation across the audio range, extending into very low frequencies, with constant amplitude. Modulating the filter response is akin to modulating the phase of the self-oscillation tone.• Unique routing possibilities Continuously variable (and CV-controlled) routing from single to parallel to series. With a signal patched into filter 2's audio input, the routing knob and CV act as a crossfader. Filter 2's cutoff can be set relatively to filter 1's cutoff.DIY-Kit-Type:PCB only Kit. This is a do-it-yourself PCB kit, no parts or Panel are supplied, you will need to source them yourself.
€8.90*
AF Labs - MI Clouds (PCB)
available
Features:Audio buffer acquisition• Stereo I/O. Even with a mono recording buffer, a wide stereo output can still be simulated by randomly panning grains or through the stereo reverberator.• Stereo pre-amp with a gain range covering modular and line levels.• Recording buffer size: 1s (32kHz, stereo) to 8s (16kHz, µ-law, mono).• The FREEZE button and the corresponding gate input freezes the content of the recording buffer, allowing you to dive into its sonic details.• 4 memory slots for storing and recalling buffers.Granular synthesis• Grain generation time base: periodical, randomized, or externally clocked.• The POSITION knob selects from which part of the recording buffer the grains are extracted.• Grain size from 16ms to 1s.• Up to 40 to 60 concurrent grains (depending on recording buffer resolution).• Transposition from -2 octaves to +2 octaves, with V/O tracking.• Grain envelope continuously variable between boxcar, triangle and Hann functions.• CV inputs for all grain parameters, individually sampled and held by each grain. For stochastic, Xenakis-style explorations, try feeding random voltages to those!• Diffusion network with 4 All-pass filters to post process the granularized signals.Post-processing ("blending") settings4 post-processing parameters are controlled by the BLEND knob and CV input:• Dry/wet balance.• Random panning amount.• Feedback amount.• Reverb amount.DIY-Kit-Type:PCB only Kit. This is a do-it-yourself PCB kit, no parts or Panel are supplied, you will need to source them yourself.
€8.90*
AF Labs - MI Elements (PCB)
sold out at the moment
Features:Excitation signal generator• Three generators with mixer: bowing noise, blowing noise, percussive impulses.• Envelope contour for bowing and blowing.• Bowing noise generator: particle-like scratching noise with 2-pole low-pass filter.• Blowing noise generator: granular pitched noise with wavetable-like scanning between various tone colors.• Percussive impulse generator: interpolates through a collection of impulsive excitations – including sampled sticks, brushes and hammers, and models of damped mallets, plectrums, or bouncy particles. 2-pole low-pass filter and pitch control.Modal resonator• Internally uses 64 zero-delay feedback state variable filters.• Coarse, fine and FM frequency controls.• Geometry: Interpolates through a collection of structures, including plates, strings, tubes, bowls.• Brightness. Specifies the character of the material the resonating structure is made of – from wood to glass, from nylon to steel.• Damping. Adds damping to the sound – simulates a wet material or the muting of the vibrations.• Position. Specifies at which point the structure is excited.• Space. Creates an increasingly rich stereo output by capturing the sound at two different points of the structure, and then adds more space through algorithmic reverberation.Designed for Eurorack• All exciter and resonator parameters have a dedicated CV input with attenuverter.• Strength input, for amplitude control of the exciter section.• Frequency control through a V/O input controlling the main resonator frequency, and an FM input.• Two audio inputs: one pre-envelope and diffuser, the other patched straight to the resonator.• Stereo audio output, with adjustable width/reverberation. It is also possible to output the raw exciter signal on one channel, and the raw resonator signal on the other.DIY-Kit-Type:PCB only Kit. This is a do-it-yourself PCB kit, no parts or Panel are supplied, you will need to source them yourself.
€9.90*
AF Labs - MI Rings (PCB)
available
Features:Three resonator models• Modal resonator, as used in Elements.• Sympathetic strings, modelled by a network of comb filters.• String with non-linearity/dispersion (comb filter with multimode filter and non-linearities in the loop).All resonator models can be used polyphonically, with 1, 2 or 4 polyphony voices.Voltage-controlled resonatorEach model provides a unified set of parameters, all voltage controlled, with an attenuverter:• Structure. With the modal and non-linear string models, controls the inharmonicity of the spectrum (which directly impacts the perceived "material"). With the sympathetic strings model, controls the intervals between strings.• Brightness. Specifies the brightness and richness of the spectrum.• Damping. Controls the damping rate of the sound, from 100ms to 10s.• Position. Specifies at which point the structure is excited.Easy to patch• Audio input accepting modular level signals, up to 16 Vpp.• Two audio outputs, either splitting odd/even partials in monophonic mode, or even/odd notes in polyphonic mode.• Voltage change detector on the V/O input, allocating a new polyphony voice each time a different note is played.• Internal exciter triggered by the STRUM input (filtered pulse or noise burst), allowing the module to be used without an external excitation source.DIY-Kit-Type:PCB only Kit. This is a do-it-yourself PCB kit, no parts or Panel are supplied, you will need to source them yourself.
€7.90*
AF Labs - MI Warps (PCB)
available
Features:7 signal hybridization algorithms• Crossfade.• Cross-folding.• Digital model of an analog diode ring-modulator.• Digital ring-modulation.• Bitwise XOR modulation.• Octaver/comparator.• 20 band-vocoder.Everything under CV control• CV control of modulation algorithm selection, with crossfading between adjacent algorithms.• CV control of each input's amplitude, with emulated analog saturation.• V/O CV control of the internal oscillator (when enabled).• For each algorithm, CV control of timbre richness/brightness/distortion.Built in carrier oscillatorAudio input 1 can be replaced by an internal digital oscillator with through-zero FM.Available waveforms: sine, triangle, sawtooth, pulse, filtered noise.DIY-Kit-Type:PCB only Kit. This is a do-it-yourself PCB kit, no parts or Panel are supplied, you will need to source them yourself.
€7.90*
AI Synthesis - Harmonic Mixer
only 1 left
The AI022 Harmonic CP3 Style Mixer is a discreet mixer using no ICs. As gain increases harmonics and analog warmth are added. As gain increases more, distortion and phasing is added, creating new waveforms from old ones.The AI022 takes inspiration from the legendary Moog Modular CP3 style mixer, but updates it for eurorack and allows for user customization of the circuit. Many Moog Modular users attribute the CP3 mixer module to providing much of the warmth of the Moog Modular sound.An exposed Bias knob allows abuse of the circuit, and allows for faithful replication of incoming audio, or radical analog wave shaping and distortion. It is also possible to use the Bias knob to adjust a +/- 5V signal into a 0/+ or 0/- signal.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€64.00*
Apollo View - Curiouser
only 2 left
The Rabbit Hole 6HP Expander adds two additional input channels to your system, offering enhanced routing options. Each channel can be sent directly to Rabbit Hole or used independently as a standalone VCA. When operating in standalone mode, both channels are normalled to sum at the bottom output for flexible signal processing. Gain CV is also normalled from Rabbit Hole for seamless integration.Features:• Expander for Rabbit Hole• 2 inputs with vintage character OTA VCA• Each channel can be used as a standalone VCA• Attenuverters for CV inputs• All analogue signal pathDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€130.00*
Apollo View - Manic
sold out at the moment
Developed with DivKid, Manic is a compact 8HP dual VCA module built for advanced sound sculpting. It supports mono, dual mono, or true stereo workflows with precision linear VCAs and selectable unipolar or bipolar response—ideal for amplitude shaping or ring modulation.Each channel features a dedicated post-VCA shaping stage:Shape1 delivers TanH soft clipping and classic Serge-style wavefolding.Shape2 adds hard clipping and a Buchla-inspired wavefolder.The asymmetrical design between channels creates rich, animated stereo effects from mono or stereo sources—perfect for depth and width in modular mixes.Optimized for both CV and audio, Manic is a performance-ready tool that brings hands-on control, creative modulation, and stereo imaging into any Eurorack setup.Features:• A collaborative design from both DivKid & Apollo View Modular• Selectable unipolar or bipolar VCA circuitry per channel• Three distinct shape outputs per channel: Inverted, Clipped, and Wavefolding• TanH soft clipping & hard clipping• Serge style wavefolding & Buchla style wavefolding• Stereo operation with perfectly matched gains for the clipping and wavefolding circuits, creating a stunning stereo widening effect• DC-coupled signal path for processing both audio and CV signals• Input and modulation normalisations for simple mono to stereo operation• Flexible signal flow allows for creative combinations, such as ring modulation into clipping or wavefoldingDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€238.00*
Apollo View - Rabbit Hole
sold out at the moment
Rabbit Hole is a 16HP summing mixer that blends solid-state precision with rich tube character. Featuring two input channels with independent vintage VCAs, it routes signals through a drive stage for solid-state clipping, followed by a starved cathode dual-triode vacuum tube for saturated warmth and harmonic distortion. An optional OWTH diode LED clipping circuit adds aggressive, dynamic edge.Features:• 2 channel mixer with vintage character OTA per input VCAs• 12AU7 Vacuum Tube Core• Fat sounding all analogue signal path• 4 possible stages of distortion• Tone shaping with CV control• Dry/Wet Mix with CV control• Feedback with CV control• Attenuverters on all CV inputs• Switchable diode clipping circuit “OWTH - Off With Their Heads”• “L8” Switch to change Tube characterDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€279.00*
AtoVproject - cDVCA (Black)
sold out at the moment
cDVCA or class-D VCA is a new kind of VCA based on an entirely novel concept that is inspired from class-D amplification technology. This is not a transparent VCA and brings a lot of character to the sound.The first VCA that tracks 1V/octConcept: The input signal is turned into an ultrasonic PWM signal (~34kHz). The PWM is scaled to the desired amplitude and then filtered back down to the original signal.The twist: The PWM frequency can be lowered down into the audio spectrum and the frequency can be controlled via its 1V/oct input allowing for crazy waveshaping that tracks your melodies.The drive controls an innovative clipping method that does not rely on overdriving any circuitry and therefore results in distortions with a very defined character.The signal then goes into a 1 pole VCF/tone circuit that allows to keep things under some amount of control as the harmonics produced by this module can be very aggressive.With no input the module generates a simple square wave and therefore can be used a simple synth voice (VCO→VCA-VCF)DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€185.00*
AtoVproject - cDVCA (Silver)
sold out at the moment
cDVCA or class-D VCA is a new kind of VCA based on an entirely novel concept that is inspired from class-D amplification technology. This is not a transparent VCA and brings a lot of character to the sound.The first VCA that tracks 1V/octConcept: The input signal is turned into an ultrasonic PWM signal (~34kHz). The PWM is scaled to the desired amplitude and then filtered back down to the original signal.The twist: The PWM frequency can be lowered down into the audio spectrum and the frequency can be controlled via its 1V/oct input allowing for crazy waveshaping that tracks your melodies.The drive controls an innovative clipping method that does not rely on overdriving any circuitry and therefore results in distortions with a very defined character.The signal then goes into a 1 pole VCF/tone circuit that allows to keep things under some amount of control as the harmonics produced by this module can be very aggressive.With no input the module generates a simple square wave and therefore can be used a simple synth voice (VCO→VCA-VCF)DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€185.00*
Befaco - A*B+C (Discontinued)
sold out at the moment
This is the 2025 version! A*B+C is a dual, four-quadrant multiplier with VC Offset that can act as Dual Ring Modulator, Dual VCA and Four Channel Mixer. Each section can perform the analog multiplication of two signals (A and B) and add an offset (C).Features:• Dual-channel bipolar VCA’s• Adjustable VC Offset per channel.• AM and Ring Modulation capabilities.• Output allows it to work as a four-channel mixer.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€108.00*