333modules - IN v2
only 1 left
External IN module to modular level, with L and R output and mono sum.Features:• 6,3 jacks inputs• L,R and mono output to modular levelDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€83.30*
333modules - Integrator DJ
only 1 left
Input module with DJ influence, RCA in and selectable line and phono input (RIA filter), with three modular level outputs Left, Right and Mono sum. Level gain with fader volume for live purposes.Features:• RCA input• Phono (RIA) or line• Gain and fader volumen• Stereo a Mono sum Output modular levelDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€107.10*
%
4ms - Percussion Interface & Expander
available
The Percussion Interface (PI) and PI Expander are a pair of Eurorack modules that generate gates and envelopes from acoustic drums, samplers, drum machines, and virtually any audio source.Converting microphone, instrument, line and modular signals into CV and clock/gate signals, the PI and PI Expander are suited for synchronizing sequencers or other modules to the rhythm of an audio track or live percussion. The modules can simultaneously be used as a pre-amp for microphones or line-level signals, while generating inverted envelopes useful for side-chaining. The PI module contains all the core functionality and can be used without the Expander to conserve space. The Expander requires the main PI modules and adds three gain stage options, a modular-level audio output jack, a 1/4" (6.35mm) input jack, and envelope attenuation capabilities. The two modules are only sold together, they are not available separately.Features:• Sensitivity knob, Low/Medium/High gain switch, and clipping LED• Sustain control to prevent misfires, increase gate length, and control the envelope• Envelope decay control• Non-inverted and inverted envelope outputs, useful for side chaining• Four envelope outputs: two attenuated with independent attenuators, and two non-attenuated• Envelope following or generation modes• Gate output for clocking sequencers or any unit with a clock or trigger input• Compatibility with drums, pads, samplers, microphones, piezos, drum machines, etc.• 1/8" or 1/4" input jack (6.35mm)
€124.95*
€173.70*
(28.07% saved)
ADDAC System - 203 CV Mapping
available
This is a new revision of one of our first modules, back from 2010. Now more compact in 6 HP and with an Offset CV input.The incoming signal amplitude is controlled by a [GAIN] attenuverter circuit allowing to attenuate the signal as well as invert its phase. A back jumper can set the maximum gain amount to either x1 (unity gain) or x10. DIY modifications can be made by changing its resistors. After the Gain an offset can be added to the signal, displacing the signal up or down (-5V to +5V) this can be adjusted using the [OFFSET] knob and CV input.When using no input using the [OFFSET] knob and CV input will generate an output between -5V and +5V.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€97.00*
ADDAC System - 711 Balanced Inputs
available
ADDAC711 is a dual channel Isolated DI box and is all about keeping the sound coming into your Modular free from any undesired noisy interferences, making sure that what you’re getting from your inputs is what your external hardware is actually producing. It provides galvanic electrical isolation between the Modular system and external sources preventing impedance mismatch and ground loop induced hum.ADDAC’s 711 circuit is designed around a unity 1:1 type Audio Transformer operating in the 20 Hz to 20 kHz range, this impedance matching transformer provides two fully balanced outputs (via XLR connectors).The LIFT/FLOAT/GND 3-way switch lets you choose between lift, ground or floating ground.In the LIFT position (left) the module circuit will be “lifted” to ground through a 100R resistor and a 10nF capacitor.In the FLOAT position (middle) Ground will not be shared leaving ins and outs grounds completely apart from each other fully isolating both signals.in the GND position (right) Ground will be shared between inputs and outputs, here no isolation is used.Any of these three positions may be the best form of avoiding ground loops or any other undesired interference occurring between your modular and the external hard- ware. Try out which one of these options will work best in any given situation.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€210.00*
ADDAC System - 712 Vintage Pre
available
ADDAC712 is a dual channel discrete gain staging amplifier, based on a famous discrete preamp board from the 70’s used in some legendary equipment. What caught our attention was the character of it’s clipping and resulting saturation/distortion.The module can be used with modular signals to add a distortion/fuzz character or as a preamp for an external source such as a line source, keyboard, guitar... It’s also a great side companion for our ADDAC711 Balanced Inputs.At the top an On/Off [BYPASS] switch routes the signal into the Effect (Up: Active) or to the bottom output gain stage (Down: Bypassed).The amount of amplification is set by the [GAIN] control, the maximum amount of amplification can be set by the user using the [MAX GAIN] trimmer.Up to ±5,5v the incoming signal will keep it’s integrity, beyond this point saturation will start to increase. At approx. ±6v a hard clipping will start to occur, this clipping also has a particular quality that at extreme levels it drifts the audio 0v bias reference, moving it upwards which results are similar to a Gate effect.In the middle, an x2 op-amp based output gain stage with a clipping LED, which monitors the clipping at the output, and an [OUTPUT] control to set the output volume.Having the top and middle gain stages provides flexibility allowing the user to completely distort the signal on the top stage and tame it’s output level with the second stage.At the bottom, input and output for both channels (left input is normalled into right input).DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€105.90*
ADDAC System - 714 Vintage Clip
available
ADDAC714 is a dual channel soft clipping module.Diode based passive clipping acts as a “brick wall” limiter with a fixed knee given by the inherent diode physics. A passive RC low pass circuit adds a 3,3KHz -3db low pass filter which sculpts the overall tone while also adding further character to the effect.At the top an On/Off [BYPASS] switch routes the signal into the Effect (Up: Active) or to the bottom output gain stage (Down: Bypassed).The amount of clipping is set by the [GAIN] control, it mostly works as a threshold control for how much clipping will be applied. As more clipping is applied the signal’s amplitude will also decrease, to compensate for this we set up a gain compensation stage to keep the output amplitude balanced across the Gain range.Symmetry chooses between bipolar clipping or positive clipping, this relates to the harmonics generated, bipolar for odd and even harmonics (up position) and unipolar for odd harmonics only (down position).At the second stage, an op-amp based x2 output gain with a clipping led, which monitors the clipping at the output, and an [Output] control to set the output volume.Having the top and middle gain stages provides flexibility allowing the user to completely distort the signal on the top stage and tame it’s output level with the second stage.At the bottom, Input jacks for both channels (Left input is normalled into Right input) and output jacksDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€100.00*
ADDAC System - 810 Phono Pre-Amp
only 1 left
Here's our Phono Pre Amplifier module, connect your turntable to it and bring its sound straight into any of your patches.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€95.00*
Befaco - AC/DC (discontinued)
sold out at the moment
- - - - Discontinued - - - -AC/DC is a class-compliant DC coupled audio interface in Eurorack format. With its 6 HP, it is perfect for live performance and travel Rigs.Based on Rebel Technology OWL platform, It allows sending and receiving both CV and Audio at 16 Bits 48 kHz. as well as load patches from Rebel’s library.It is compatible with all popular DAW and CV generators, and also as an audio and CV processor for iOS apps.Features:• Class-compliant audio interface• DC coupled with range -10 to 10 V• Level meters and clip LEDs• 48 Khz 16 Bit• Compatible with OWL platform• Stm32H7 processor with 32 Mb of RAMDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€199.92*
Befaco - Hexpander
available
Hexpander adds great functionality to Hexmix module. Featuring Three aux send with stereo returns, individual outputs for each channel, complete PFL system and balanced output.Hexpander is designed to be placed on top of Hexmix. Expanding Eurorack concept to 6U, allows every channel to be aligned as in traditional tabletop mixers.Features:• Three auxiliar sends with stereo returns and individual controls per channel.• Pre and Post Fader/EQ outputs.• Selectable Line/Modular level at return inputs.• Monitor section with PFL per channel.• Individual PostEq output per channel.• Master section with Headphones amp and balanced line outputsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€265.37*
Befaco - InAmp
available
Inamp is a dual pre-amp in just 4 HPs. Featuring 6,3 Jacks inputs as well as Minijacks.The unit is designed to amplify up to x20 the input signal, allowing to amplify most of the music machines out there (Domestic line levels) as well as some guitars (Humbucker-like pickups and so).DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€76.16*
Befaco - Instrument Interface
available
Instrument Interface is an eurorack pre-amp capable to bring any type of audio signal to modular levels thanks to its amplification circuit.The module can drive regular and condenser microphones (+48V Phantom Powered) as well as Instrument and Line signals with a very low distortion ratio.Instrument Interface offers some additional extra functions like a Trig/Gate extractor and Envelope Follower circuits, allowing you to use the character of your audio signal in more creative waysFeatures:• Neutrik combo Input• Phantom Power selector• Input Impedance selector• Separated Audio en Envelope Level controls.• Envelope Follower with attack and decay control• Gate and Trigger Extractor with threshold selector.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€154.70*
Befaco - Lich
only 1 left
Lich is a programmable multi-function module based in the Rebel Technology OWL platform that allows you to use Pure Data, Max Gen or Faust code into your module!.Lich is a Befaco Rebel collaboration that brings back Owl’s platform with this new hardware iteration. It has stereo in and out, four pot controls summed to cv inputs (like the classic Owl module) And as addition, CV and Gate outputs, patch selection with display and USB MIDI host and device connections.Features:• Stereo Audio IN and OUT at 48k 24 bits.• 4 CV controls (Pot + Attenuated CV in)• 2 CV outputs.• 2 Gate intputs + buttons.• 1 Gate Output.• Patch selection and visialization via display.• USB host and Device connectionsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€201.11*
New
Befaco - Oneiroi
only 1 left
Experimental synth voice focused on ambient pads and drone-like soundscapes.Features:• Stereo External input with selectable gain.• 5-second looper Records either the stereo input or the module’s output• Sine oscillator• Supersaw oscillator• Wavetable oscillator that uses the Looper buffer• Multimode filter: low-pass, band-pass, high-pass, and comb filter.• 3-band resonator• 2-tap echo• Reverb with macro control for size, filtering, and direction.• CV Control with attenuators on most parameters.• Various types of self-modulation with configurable routing and control over level and speed.• External synchronization via sync input.• Powerful randomizer with four different targets, three levels of intensity and undo/redo.• Knobs catch behavior functionality for re-coupling parameters’ positions.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€329.00*
Befaco - TRS 1U
available
Total flexibility for the Befaco 7U or Intellijel cases rear connectors jacks. The channels are reversible and can be used independently for input or output.4 Inputs or Outputs (per module) can be obtained by “AND” cables. Independent tip and ring attenuators are selectable for each channel to convert the modular input level to line output level.Features:• Selectable atenuator per channel.• Fully compatible with Intellijel’s 7U and Palette cases.• 1U Intellijel format.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€35.70*
Befaco / DivKid - Output Bus
available
The Output Bus is your ultimate output module: Presented by DivKid and Befaco, meant to be the last link in your modular chain!Inspired by pro audio and studio summing units the Output Bus allows for summing style mixing, external gear integration, soft clip limiting, flexible output types, headphone monitoring and level visualization.The module works great mixing all your other mixers in your setup, to return mono or stereo FX into the master bus and for bringing in external stereo line level gear with ease. All of this in just 8HP while also being able to visualize your final levels, output appropriate signals on the right cable type and monitor in headphones.Features:• Six stereo inputs.• Line/synth selector in input six.• Modular level minijack out.• 6,5 mm Jack balanced out.• Minijack and 6,5 mm phones out.• Led Vu-meter.• Soft clipping circuit at main output.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€155.00*
Black Noise Modular - GOMA Pro
only 2 left
The GOMA Pro pushes the boundaries of the attenuverter-mixer concept.Attenuator, attenuverter, offset generator, voltage generator, waveshaper, distorsion, GOMA Pro can do all of that and more. Engineered for precision, GOMA Pro is crafted using high-quality components to ensure maximum accuracy, including low-tolerance resistors and low-noise op-amps.GOMA Pro offers 3 channels fully analog to amplify (up to x10 gain!), attenuate or polarize (attenuverter) any signal, from CV, audio to line level sources.Additionally, each channel can act as a high precision voltage generator (–10V to +10V) to offset another channel or control external parameters.The 3 channels can be processed separately or summed through cascade mixing, which can extend further than a single module since all the GOMA family (I, II, Pro) can be daisy chained to unlock virtually infinite mixing.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€113.00*
Frequency Central - Meth Amp
available
Meth Amp is based around the fuzz core of the EH Big Muff pedal. Lovely fuzz and distortion based on the classic Big Muff pedal! It’ll do wooly warm fuzz, subtle tone shaping with a soft saturation/colour, feedback madness and work as a great output VCA (LPG style tones possibly too). The clipping diodes have been replaced by red LEDs to take account of the change in power supply from 9V in the original Big Muff to +/-12V in Meth Amp.To the fuzz core has been added a bunch of OTAs, each controlling a different aspect of audio processing: gain, regen (a new feature - not present in Big Muff), tone and volume. Thereby, each feature is fully voltage controllable.Additionally, there is a separate x100 preamp which can be used to boost external audio for further processing by Meth Amp. Here is a Video about it.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€100.00*
Frequency Central - Thermo Nuclear
available
ThermoNuclear is a sub-miniature vacuum tube based overdrive. The first stage is a MOSFET with switchable mu-amp. The second stage is a self biased sub-miniature pentode with switchable triode/pentode. Then there’s a tonestack based on the EH Big Muff. Finally, there’s a blend control and another MOSFET stage for some gain recovery after the tonestack. ThermoNuclear will crush and destroy your tone with a pleasing warm tubey goodness.Although the filament of the tube will glow, it’s not a lightbulb, and the level of glow may vary between different tubes.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€111.32*
Ginko Synthese - Mic
sold out at the moment
Mic from Ginko Synthese is a 2HP Eurorack microphone pre-amp module. It was designed to work with Ginko Sampleslicer but can also be used to amplify and send your microphone signal to any other module in your Eurorack system.It works with electret mics (included).Features:• Input• Gain control• Momentary on push button• On/off switch• Output• Included mini jack microphoneDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€54.74*