Effects
available
Strakal Brulu is a great sounding Germanium Fuzz Module. Very characteristic for the module’s sound if the feedback that is coupled to the feedback. The more fuzz, the more feedback. The Strakal Brulu 2 can get pretty nasty and it screams a lot at high fuzz settings and low input level. The fuzz amount can be voltage controlled, with an inverse attenuator.Features:• 2 NOS Germanium Transistors• Cv controled by vactrol• Classic Fuzz sound for mudular levels• Feedback screamingDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
The two fuzzes share the same controls. The Fuzzes and EQ are slightly differents (great for strereo). You can output the Stereo signal by plugin a stereo cable or you can output a mono signal : Fuzz1 - clock wise or Fuzz2 - counterclock wise, or a mix of the 2 fuzzes by turning the morphing pot.Features:• Selected Silicon transistors• Mono input• Stereo output - with stereo cable• Mono morphing output - with mono cable• Feedback (with cv control)• EQ (low high)• Morphing (with cv control) Clock wise Fuzz1, counter clock wise Fuzz2• Input Volume• Gain• Stupid Breton nameDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Strakal Orsel is a tube distortion module that injects organic, vintage character into a modular setup. True to Touell Skouarn tradition, control labels use Breton terminology, while input and output are marked with arrows for clarity.The unit’s topology offers flexible tonal shaping: the Triodenn selector changes the left tube between pentode and triode operation, altering the core sound. The Boukl Retroaktiñ control combines a feedback engage switch with a level pot that ranges from subtle thickening to full, screaming self-oscillation. Gounid sets the balance between the first and second stages. Ampled governs the amount of saturation. A dedicated CV input, Enkas Modulañ, lets external control influence feedback and overall level even when feedback is not engaged.Beyond straightforward distortion, the circuitry produces rich secondary behaviors. With feedback pushed wide the circuit behaves as a powerful effect oscillator whose pitch responds to CV (not calibrated to strict 1 V/oct tracking). With feedback off and conservative level settings, the unit exposes its tube noise floor and can operate as a raw, characterful VCA.Features:• Tube distortion module• Exposes tube noise floor for characterful texture• Can function as a crude VCA• Compatible with 6j1P, 5654, 6AK5 and EF95 tubes• Boutique construction, made in Plougastel-DaoulasDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The Foldiplier is a 4 HP odd/even harmonics generator with 2 different oscillating feedback paths. The folding core of the design originates from the odd harmonics (middle)section of the Serge Wave Multiplier. But the Foldiplier adds voltage control over the symmetry and offset as well as a switch for feedback, jumper selectable between, a transistor based oscillating fuzz inspired by the Hemmo Bazz Fuss with a lot more low harmonic content and a passive oscillating half wave rectification circuit with more high harmonic content. When these feedback oscillations mix with an incoming waveform some unpredictable and unique nonlinear timbres can be achieved. The module can also be used as a no-input experimental oscillator with the feedback switch engaged. All diodes in the module are silicon.The Fold knob controls the amount of times the waveform is folded in on its self (indicated by the red led window below the knob). The C.V. knob below is an attenuator for incoming control voltage corresponding to the Fold jack(indicated by the red led window above the jack, it only responds to positive voltage). So, the Fold knob acts like an initial amount of folding depending on its position. For example, with the Fold knob fully clockwise you can get even more folds with a control voltage in at the Fold jack. The Offset knob controls how much positive DC voltage(0 to 5v, clockwise) or negative(0 to -5v counter clockwise) DC voltage(indicated by the led window above the Offset jack, red for positive, yellow for negative) injected into the waveform via the Symmetry knob. With the Offset knob position at noon(0v) there will little effect from the Symmetry knob. The Offset jack is expecting +5v to -5v with knob position at noon to scan through the positive and negative voltage. The Symmetry knob controls the amount of negative or positive offset voltage(dependent on the Offset knob) mixed with the waveform(indicated by the yellow led window above the Symmetry jack). If positive voltage is mixed with incoming waveform more folds will occur on the positive troughs of the waveform, likewise, when negative voltage is introduced more folds happen on the negative troughs. This part of the circuit can also be broken down by thinking of the Offset as a voltage controlled crossfader swinging between positive and negative voltages into a VCA controlled by the Symmetry knob and jack. When a voltage is present at the Symmetry jack the Symmetry knob becomes an attenuator. The Symmetry jack only responds to positive voltageDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
VC F3DB stands for Voltage Controlled Fixed Filter Feedback Distortion Bank. The simplest description is it’s an analog 16hp six band voltage controlled fixed filter bank. But with the additions of so much gain, clipping, feedback, and self-oscillation it becomes a very flexible and unique gestural sound sculpting tool capable of; graphic equalization over 6 octaves, multi-band distortion, spectral processing, crude vocoding, multi-frequency envelope following, self-modulation, and even as an instrument on its own. With no input it can be used as a pseudo chaotic “harmonic” feedback oscillator.The filter frequencies were specifically chosen to emphasize more ambiguous and dissonant intervals. Although the frequency bands are spread out over many octaves I purposely tried to leave out “3rds” besides a major 10th at the top frequencies to even out all the dissonance below. But the frequencies aren’t exactly equal tempered, so it’s relative. The bands roughly equate to F2, B3, F#5, C6, F7, A8.The design is based on the Moog 914 filterbank, which it borrows the frequency bands from. But this circuit uses active filters with opamps inspired by YU Synth opposed to passive cells using inductors on the original. The 88hz is a low pass -24db/oct and 7k is a high pass -24db/oct, the rest are -12db/oct band pass filters all with a Q around 4.The hard and soft clipping circuit on the input is fairly standard which appears in many different iterations of classic guitar pedals. But it has a lot of gain and can even boost line level signals. What makes it a bit unique is the feedback on the clipping circuit which needs to be turned on by the GFB(gain feedback) switch and the amount can be controlled by the Gain FB pot which can add some fuzz/bite to the signal depending on which clipping switch is engaged or at the extremes it will self oscillate from audio rate to LFO sort of clicking range. All the clipping stages in the module are using silicon diodes.Consult the Signal Flow Chart to the left for a rough visual breakdown of the controls,in/outs,normalizations, and optional settings for the module.Each band can also be muted by the top toggle switches or clipped(at the VCA) by the top slide switch which makes this design a bit different than other filter banks. As well as the overall feedback section(bottom middle) takes the sum/all bands out through a VCA(controlled by the feedback pot and FB CV) back to the input gain/clip circuit. and you can also tap into this using different sends/bands to the FB In jack to break the normalization. With this extra feedback “resonance” you can get more whistley and howly filter sounds kinda like the Serge res eq, which can also go into self oscillation.All CV ins are expecting +5v to open the VCAs (they wont respond to negative voltage), once you get closer to +8v or so it can clip the VCA regardless of the gain settings or clip switches. Output amplitude in high gain settings will exceed 10vpp and can get up to 20vpp. The envelope followers tend to stay around 0-5v out, but with clip switch active they can go up to 10v.Since this is a high gain module there can be bleed between the bands in certain configurations and situations. Also in high gain modes with higher frequencies the 2.8k and 7k bands can bleed a little with the VCAs closed.This is a highly involved DIY all through hole project. It is a long build with 5 different pcbs to solder and assemble.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Kaseta is a multi-purpose Eurorack module inspired by reel-to-reel tape machines. It models magnetic hysteresis for warm tape-style saturation and provides four independent, freely positioned reading heads that can create conventional echoes, rhythmic patterns, looping textures and complex feedback networks.Up to five minutes of audio can be recorded. Dedicated tone, wow and flutter controls shape the tape character, while individual head controls and stereo panning turn the four taps into a flexible spatial delay. The preamp can move from attenuation to strong drive, and saturation can be pushed beyond its normal limits for harsher distortion.Four assignable control inputs make nearly every parameter voltage controllable. Kaseta also includes an internal 1V/oct oscillator and a trigger sequencer derived from the delay heads, allowing it to work as a delay, sound source, rhythm generator or modulation utility.Features• Four-head tape-style delay• Up to 5 minutes of audio recording• Magnetic hysteresis saturation simulation• Tone, wow and flutter controls• Individual head position, speed, feedback, volume and pan• Stereo output• Four assignable CV inputs• Internal voltage-controlled oscillator with 1V/oct tracking• Trigger sequencer and impulse output• 24-bit / 48 kHz audio• LED parameter visualizationDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.