Potentiometers
available
Potentiometer, vertical PCB mount.Rotation angle approx. 300°. 6 mm D shaft shaft for push-on knobs or knobs with set screw, shaft length 15 mm including thread. 7 mm mounting hole required in the front panel.Nut and washer included.
available
Linear potentiometer, vertical PCB mount.Rotation angle approx. 300°. 6,35 mm round shaft for knobs with set screw, shaft length 15 mm including thread.Nut and washer included.
available
Potentiometer, vertical PCB mount.Rotation angle approx. 300°. 6 mm T18 shaft for push-on knobs or knobs with set screw, shaft length 15 mm including thread. 7 mm mounting hole required in the front panel.Nut and washer included.
available
Dual Potentiometer, vertical PCB mount.Rotation angle approx. 300°. 6 mm D shaft for knobs with set screw, shaft length 15 mm including thread. 7 mm mounting hole required in the front panel.Nut and washer included.
available
Dual Potentiometer, vertical PCB mount.Rotation angle approx. 300°. 6 mm T18 shaft for push-on knobs or knobs with set screw, shaft length 15 mm including thread. 7 mm mounting hole required in the front panel.Nut and washer included.
available
Taiwan Alpha slider potentiometer RA2045F-20R-15LC-B10. Discounts available atomatically at larger numbers. • 10 kΩ linear (B) taper• No center dent• Integrated red LED• 20 mm travel distance• Mounting (body) height 7 mm• Total body length 35 mm• Total body width 9,4 mm• Lever height 15 mm• Sliding life 15.000 cycles
available
Alpha RD901F vertical potentiometer with various resistances. Body height = 10mm.5mm threading plus 10mm shaft = 15mm from the body in total.M7X0,75 threading, needs a 7,5mm hole. Rotation angle 300° (6,35mm diameter).
available
Alpha RD902F dual (stereo) vertical potentiometer with various resistances. Body height = 10mm.5mm threading plus 10mm shaft = 15mm from the body in total.M7X0,75 threading, needs a 7,5mm hole. Rotation angle 300° (6,35mm diameter).
available
Alps RK09 dual (stereo) vertical potentiometer with various resistances and tapers. Body height = 10 mm. 5 mm threading plus 12 mm shaft = 17 mm from the body in total. The shaft starts with a 5 mm long round shaft and then changes into a 7mm long D-shaft (usual 6 mm diameter), means it’s kind of stepped. M9x0,75 threading, needs a 9 mm hole. Rotation angle 300°.
available
Transparent potentiometer which can be used as a backlit knob if you install an LED below the potentiometer.Nut and washer included.
available
Dual Potentiometer, vertical PCB mount.Rotation angle approx. 300°. 6,35 mm Round shaft for knobs with set screw, shaft length 15 mm including thread. 7 mm mounting hole required in the front panel.Nut and washer included.
available
Song Huei R16K1, B100k (lin), horizontal, 6mm round shaft, PCB mount. Shaft length incl. threading is 15mm, without threading it’s 8mm. M7x0,75 threading, needs a 7mm hole. Rotation angle 300°. This is one of the classic pots for guitar effect boxes.
available
Song Huei RK1114N linear potentiometer vertical. Rotation angle 300°. 6mm D shaft for push-on or knobs with set-screw, shaft length "L" 17,5mm (including threading). M9 hole needed in front panel. Nut and washer included.
available
The usual Song Huei R0904N alias tall trimmer pot. Vertical 9mm snap-in trimmer potentiometer with knurled 17mm long shaft. Linear (B) and logarithmic (A) taper, black, blue or red shaft (colors might run out, black should be always available). Rotation angle 280°. 6mm diameter round, knurled shaft with white indicator line.
available
Tayda Potentiometer with 6mm T18 shaft. Shaft length incl. threading is 17mm, without threading it’s 10 mm. M7x0,75 threading, needs a 7 mm hole. Rotation angle 300°.