333modules - 4xLFO
only 2 left
Quadruple LFO with four triangle outputs and four square output, swith with range selector for oscillations audio frequencies.Features:• 4 x LFOs• LFO and audio frequencies• Triangle and square outputsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€101.15*
333modules - Cv4Lfo
available
4 LFOs, triangle and square outputs per channel and CV input and pot for modulation.Features:• 4 x LFOs• Triangle and square outputs per channel• CV input per channelDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€107.10*
333modules - Decade
only 2 left
Four decay envelopes with CV.Features:• 7 V peak output• Release: Aprox. 1 ms to 3 min.• Cascade trigger input• CV per channelDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€107.10*
333modules - Dual ASR
available
• 2x ASR• LFO loop mode (150Hz - 3sec)• 7,5V peak output• Cascade trigger inputDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€107.10*
333modules - Dual LFO S&H
available
Two channel LFO with Triangle and Square outputs. The frequency range selector allows you to use it at audio frequencies. Each channel counts with an additional Sample and Hold circuit which can be synchronize with your own signals thanks to its dedicated Trigger and S&H Inputs.Features:• 2 x LFO output (triangle and square)• 2 x Sample and hold output (+/- 5V auto generated by LFOs in disconnection)• Trigger and S&H in inputs• LFO selector (lfo or audio speed)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€101.15*
333modules - Env-Foll
sold out at the moment
Envelope follower with preamp, level and 2 outs: Gate out, envelope out.Features:• Fine pot to adjust levels• Gate out, envelope outDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€83.30*
4ms - Noise Swash
sold out at the moment
The Noise Swash is a chaotic random noise-maker and CV generator, generating its own sounds or working as an audio processor. As a stand-alone device it generates unpredictable continuously morphing oscillations on the Audio Output jack, and random CV fluctuations out the dual-direction "Mood CV" jack. A second CV input jack controls the Swash and Noisegate sections with positive and negative CV voltage. An audio input jack allows for distorting an audio signal beyond recognition, or using audio to trigger and modulate the chaos. The Swash knob is a 10-turn Bourns pot for adjusting minor variations. Each Swash has its own peculiarly unique sound.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€149.35*
%
4ms - Percussion Interface & Expander
available
The Percussion Interface (PI) and PI Expander are a pair of Eurorack modules that generate gates and envelopes from acoustic drums, samplers, drum machines, and virtually any audio source.Converting microphone, instrument, line and modular signals into CV and clock/gate signals, the PI and PI Expander are suited for synchronizing sequencers or other modules to the rhythm of an audio track or live percussion. The modules can simultaneously be used as a pre-amp for microphones or line-level signals, while generating inverted envelopes useful for side-chaining. The PI module contains all the core functionality and can be used without the Expander to conserve space. The Expander requires the main PI modules and adds three gain stage options, a modular-level audio output jack, a 1/4" (6.35mm) input jack, and envelope attenuation capabilities. The two modules are only sold together, they are not available separately.Features:• Sensitivity knob, Low/Medium/High gain switch, and clipping LED• Sustain control to prevent misfires, increase gate length, and control the envelope• Envelope decay control• Non-inverted and inverted envelope outputs, useful for side chaining• Four envelope outputs: two attenuated with independent attenuators, and two non-attenuated• Envelope following or generation modes• Gate output for clocking sequencers or any unit with a clock or trigger input• Compatibility with drums, pads, samplers, microphones, piezos, drum machines, etc.• 1/8" or 1/4" input jack (6.35mm)
€124.95*
€173.70*
(28.07% saved)
4ms - Pingable Envelope Generator (Black)
only 2 left
The Pingable Envelope Generator (PEG) from 4ms is a dual envelope generator whose envelope lengths are set by incoming clocks or "pings".The PEG has full CV control of envelope shape, skew, and ping (clock) division/multiplication, as well as a plethora of triggering and cycling options (AD, AR, quantization, cycle), and a tap tempo button for each channel.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€215.39*
4ms - Pingable Envelope Generator (Silver)
only 2 left
The Pingable Envelope Generator (PEG) from 4ms is a dual envelope generator whose envelope lengths are set by incoming clocks or "pings".The PEG has full CV control of envelope shape, skew, and ping (clock) division/multiplication, as well as a plethora of triggering and cycling options (AD, AR, quantization, cycle), and a tap tempo button for each channel.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€215.39*
4ms - Quad Pingable LFO (Black)
available
The Quad Pingable LFO (QPLFO) is a compact, playable four-channel tap-tempo, clock-syncable LFO with variable skew and reset.The QPLFO is designed to be useful in small portable systems that require maximum functionality in minimal space, as well as large systems that need maximum modulation sources.Features:• Quad "pingable" LFO's -- frequency is set by time between pulses ("ping")• Each of the 4 channels is an independent LFO• Can produce a variety of waveshapes: "Pluck," to ramp-down, to triangle, to ramp-up, and all shapes in between• Channels can easily modulate, trigger, and reset each other for complex and slowly morphing outputs• Slowest period is about 71 minutes (0.0002 Hz), fastest speed is about 500Hz (marginal tracking up to 1kHz)• Tap tempo button is free-running (LFO runs indefinitely), but external clock/Ping is auto-stopping (LFO stops when external clock stops)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€204.68*
4ms - Quad Pingable LFO (Silver)
only 2 left
The Quad Pingable LFO (QPLFO) is a compact, playable four-channel tap-tempo, clock-syncable LFO with variable skew and reset.The QPLFO is designed to be useful in small portable systems that require maximum functionality in minimal space, as well as large systems that need maximum modulation sources.Features:• Quad "pingable" LFO's -- frequency is set by time between pulses ("ping")• Each of the 4 channels is an independent LFO• Can produce a variety of waveshapes: "Pluck," to ramp-down, to triangle, to ramp-up, and all shapes in between• Channels can easily modulate, trigger, and reset each other for complex and slowly morphing outputs• Slowest period is about 71 minutes (0.0002 Hz), fastest speed is about 500Hz (marginal tracking up to 1kHz)• Tap tempo button is free-running (LFO runs indefinitely), but external clock/Ping is auto-stopping (LFO stops when external clock stops)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€204.68*
ADDAC System - 214 VC Rotator
available
This is our VC Rotator, a stepped routing module for any type of signal (audio, cv, gate, trigger...)Similar to a VC switcher but in this case there's the same number of inputs as outputs so, instead of 4 to 1 or 1 to 4, this module is always 4 to 4 but it can be patched for 2 to 2 and 3 to 3 step actions.All four inputs get routed to the four outputs depending on the CV and Clock controls and are divided into 4 routing steps:1. routes all inputs to the same number output: 1:1, 2:2, 3:3, 4:42. routes all inputs to an offset of 1: 2:1, 3:2, 4:3, 1:43. routes all inputs to an offset of 2: 3:1, 4:2, 1:3, 2:44. routes all inputs to an offset of 3: 4:1, 1:2, 2:3, 3:4Direction determines if the clock input goes forward or backwards.Going forward it can be set to 2-3 or 4 steps using the Rotate knob offset, going backwards always sync to 4 steps even if offseted by the Rotate knob.For 2 & 3 step action input 1 is normalled to input 3 and input 2 is normalled to input 4.Reset resets the internal clock to the first step.Pendulum, external sequencing or any complex CV actions can be achieved using the CV input and dedicated attenuverter.4 LEDs monitor which input is routed to output 1.Features:• 4 Inputs• 4 Outputs• Direction Switch• CV Rotate with Attenuverter• Clock and Reset Inputs• 4 Monitor LedsDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€145.00*
ADDAC System - 215 Dual S&H
available
This new module should not be judged by its size, at 6hp it’s packed with features.At its core it features a noise source and two precision Sample & Holds that drastically reduce the typical voltage drop over time (20 minutes for a 0.01v drop) and with 0.3% of maximum deviation from the Input which allows for quantized signals to be sent through without any noticeable detuning.The Sample & Hold sections can also be used as a Track & Hold, meaning it holds the incoming input while the Trigger input is ON and lets the input flow to the output when the Trigger input is OFF.Each section also features its own slew processor with a single control over attack and decay and an ON/OFF switch.The noise signal is normalled to both sections inputs, meaning that without a jack plugged into the Input, the sample and hold function will act upon the incoming noise signal, generating random CV values.The [Trigger A Alternate] switch allows to Link both sections so that any trigger input in Trigger A will alternate between triggering the A and B section.Besides each section outputs there are also 4 extra outputs: Noise, Difference, Average and Sum. The [Noise] output is coming from the noise source, the [Difference] output is the subtraction of section A minus section B, the [Average] output is the sum of both A plus B and then divided by 2 and finally the [Sum] output is the sum of both A plus B sections.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€139.00*
ADDAC System - 306 VC Transitions
only 2 left
ADDAC306 is a 5 channel multi-directional CV generator.You can think of it as a "sweet spot" controller, or a hands-on way of transiting from one state to another.Each of the five channels has MINIMUM, SPAN and DIRECTION controls, a common CV IN and a common TRANSITION CONTROLLER slider.MINIMUM sets the minimum channel voltage.SPAN sets the voltage range of the channel.It essentially sets the maximum voltage that can be output from the channel, relative to what the current channel MINIMUM is. For a given SPAN value, if the MINIMUM voltage is changed then the maximum voltage output from that channel will also change respectively.DIRECTION sets whether the voltage transition for each channel goes from MINIMUM to maximum, or maximum to MINIMUM.The TRANSITION CONTROLLER slider controls the transition from the minimum value (A) to the maximum value (B) or vice versa, according to the settings of each independent channel.Moving this slider generates 5 different voltages with 5 different ranges and directions. The transition can also be operated from a CV source at the CV IN, in which case the slider position acts as an attenuator for the incoming voltage.The maximum range of each channel can be set to either 5 or 10 volts, by 5 jumpers in the back of the module. Only positive voltages are generated at the output.Using the CV IN you can use two ADDAC306 modules to expand your control options to 9 voltage outputs under one common slider control.Use the VC Transitions to multiply the polyphony of a single CV sequencer by passing its outputs through the ADDAC207.VC Transitions makes for an awesome state transition controller. Plug its outputs to various CV controller parameters of your audio effects modules. Set the slider to position A, and set the minimum values for each channel. Then move the slider to position B and set the SPAN settings for each channel. Use the TRANSITION CONTROLLER slider to morph from state A to state B and backwards. Flip the DIRECTION switches to change the direction of the transition for each channel. Use the CV IN to automate the transition using LFOs, ADSRs or sequencers.Plug the output of your ADSR envelope to the CV IN and set the channels differently to get 5 different ADSRs from one common source.This module's development was based on an initial idea by Konstantine Fioretos.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€113.90*
ADDAC System - 307 Heart Sensing
available
Another addition to our ADDAC300’s Expressive Controls Series.Preceded by the release of our ADDAC303 Muscle Sensing module this is the second module we make to take advantage of the physical body as a control source.This module originated from a simple idea: using one’s heart beat as a control source.Using a clip-on sensor, that can be attached to a finger or an ear lobe, the user’s heart rate will be acquired by sensing the blood flow passing under the sensor. This pulse will generate a trigger and an AD envelope.Clip-on sensor will be provided with the module.Features:• 0 +5v Trigger output• 0 +10v Envelope output with:• Attack, Decay, Amplitude and Offset controls• Two leds monitor the Trigger and Envelope OutputsDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€130.90*
ADDAC System - 308 Light to CV
available
Another addition to our ADDAC300’s Expressive Controls series. This module converts the incoming light hitting an external light sensor into 2 Bipolar CV Streams:Output: More light > Higher CV outputInverted Output: More light > Lower CV outputThe external sensor is enclosed in a jack socket in order to be used with any standard jack cable and be able to place it in any place outside the Eurorack frame.There are several controls to adjust the CV Output’s signals:• Sensitivity: Adjusts the Light Sensor sensitivity to Light. The Higher the sensitivity the better it responds to low light situations.• Response: 3 fixed settings (medium/fast/slow) to set the slew applied to the raw signal coming from the sensor.• Gain: Sets the gain for both outputs• Offset: Adjusts the Offset for the main Output.• Inverted Offset: Adjusts the Offset for the Inverted Output.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€101.00*
ADDAC System - 701 VC Oscillator V2
available
This is our new VCO; we discontinued our ADDAC701 VCO a few years back and since then we’ve been wanting to release a more stable version with better pitch tracking, increasing pitch reliability, and further minimizing the detuning issues of analog VCO’s.For this new revision we chose to use the modern version of the CEM3340 ic from CoolAudio and add the triangle to sine circuitry of our previous VCO. This new version is extremely stable over 7 octaves.We also added a new Mix section which allows mixing of all waveforms controlled by 3 knobs SIN/TRI, MIX and SAW/RECT.Features:• Frequency knob with 6 octave range• Fine Tune knob with 12 semitone range• Octave switch with 6 octave range• 1v/octave cv input• Linear FM cv input with attenuator• LFO/VCO switch sets overall frequency range• Soft/Off/Hard Sync switch• Pulse Width control with initial knob and cv input with attenuator• SINE, TRIANGLE, SAW and PULSE outputs• Mix output controlled by 3 knobs SIN/TRI, MIX and SAW/RECT.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€158.00*
Apollo View - Allscillator
available
'ALL' the oscillator waveforms in 10 HP - No ordinary 3340 VCO!Extremely stable across all temperatures, wide-ranging (0.0011Hz - 20kHz), all analogue triangle core VCO / LFO / Ultra-LFO based on 3340 VCO IC, which utilises the full potential of the 3340’s capabilities and adds additional wave-shaped outputs.Features:• 1V/oct tracking over +10 octaves• Eight simultaneously available waveforms• Unique PWM Saw• Sub Pulse waveform (-1 octave, -2 octave, -2* octave)• Audio / LFO / Ultra LFO modes (up to 15 mins)• Exponential Frequency Modulation• Linear Frequency Modulation• Exp FM and Lin FM simultaneously available• Positive edge Hard Sync• Negative edge Hard Sync• Soft Sync• 3 Sync types simultaneously available• Coarse Knob sweeps 5 octaves in Audio mode• Fine Knob sweeps -+5 semitones in Audio mode• Extremely stable across all temperaturesDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€299.88*
AtoVproject - cLFO
available
Introducing our innovative Complex Low Frequency Oscillator (cLFO) - The cLFO is an instrument for those who believe in pushing the limits of modulation. Featuring two CV-controlled LFOs that intricately intermodulate and are seamlessly integrated with a ring modulator, this module elevates your synthesis and sound design to unprecedented levels.Crafted with a focus on cross and self-patching, the cLFO invites you to explore the endless possibilities of modulation. Dive into creating continuously variable waveforms, exponential shapes, bouncing ball effects, immersive stereo soundscapes and many other sonic wonders!Each LFO outputs Triangle, Saw, and Square waves. The Triangle output of LFO1 is normalled to the CV input of LFO2 with attenuation. The addition of a ring modulator to this setup draws from years of the designer's own experimental projects. It is an invitation to experiment with effects traditionally reserved for audio in the realm of modulation. A ring modulated LFO delivers the rhythmical essence of a conventional LFOs but with an added complexity and variability that ensures your soundscapes are always evolving.This module offers an expansive modulation frequency range, with speed adjustments from as slow as 2 minutes per cycle to as fast as 20 cycles per second. With CV control, frequencies can stretch from 13 hours per cycle to 400 cycles per second, ensuring unparalleled versatility in your modulation explorations.Accompanying the cLFO is a detailed manual filled with lots of patch idea designed to elevate your sound design skills to new levels.Dive into the world of advanced modulation manipulation with cLFO.Stay inspired! Stay innovative!Features:• Two analog LFOs• Control voltage over LFO frequency• 3 waveform outputs per LFO: Triangle, Square and Sawtooth (LFO1 - ramp down; LFO2 ramp up)• Wide frequency range: 2 minutes - 0.05s (20Hz) without CV and 13 hours to 400Hz with CV• Ring Modulator (aka four quadrant multiplier aka bipolar VCA)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€190.00*