333modules - 4xLFO
available
Quadruple LFO with four triangle outputs and four square output, swith with range selector for oscillations audio frequencies.Features:• 4 x LFOs• LFO and audio frequencies• Triangle and square outputsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€101.15*
333modules - Cv4Lfo
only 1 left
4 LFOs, triangle and square outputs per channel and CV input and pot for modulation.Features:• 4 x LFOs• Triangle and square outputs per channel• CV input per channelDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€107.10*
333modules - Dual ASR
only 2 left
• 2x ASR• LFO loop mode (150Hz - 3sec)• 7,5V peak output• Cascade trigger inputDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€107.10*
333modules - Dual LFO S&H
available
Two channel LFO with Triangle and Square outputs. The frequency range selector allows you to use it at audio frequencies. Each channel counts with an additional Sample and Hold circuit which can be synchronize with your own signals thanks to its dedicated Trigger and S&H Inputs.Features:• 2 x LFO output (triangle and square)• 2 x Sample and hold output (+/- 5V auto generated by LFOs in disconnection)• Trigger and S&H in inputs• LFO selector (lfo or audio speed)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€101.15*
4ms - Meta Module (Assembled)
available
The MetaModule puts real knobs and jacks on virtual software modules. Step back from the computer and make music with hardware, while keeping the flexibility and expandability of software.THIS PRODUCT IS ASSEMBLED AND NO DIY!The MetaModule comes with over 160 built-in modules from 4ms Company, Befaco, HetrickCV, NonlinearCircuits, and Scanner Darkly, plus clones of popular classics such as the Mutable Instruments Eurorack modules, fun physical modeling algorithms, and lots of handy utilities.All of the included modules are also available on the computer using the free program VCV Rack. Whether you make patches on VCV Rack and transfer them to the MetaModule, or if you just create patches directly on the MetaModule, there are plenty of creative modules to inspire new ways to make music.MetaModule PluginsIf the 160+ built-in module aren’t enough, you can load more modules as plugins. Already there are over 200 modules in third-party plugins from Bogaudio, Valley, ChowDSP, NANO Modular, and the list is growing. We have an SDK available to make it easy for VCV Rack plugin developers to convert their plugin to a MetaModule plugin. Our licensing terms are non-restrictive: developers are welcome to distribute their plugin in any way they wish, commercially or not.Mapping Knobs and JacksThe MetaModule has 12 knobs that can be mapped to virtual knobs. Each knob can be mapped to up eight virtual knobs, and each mapping can have a different range and offset. You also can save a group of mappings as a Knob Set and switch between Knob Sets with the encoder. You also can map the 8 inputs and 8 outputs to virtual module jacks. Also, the MetaModule is a USB MIDI host, so you also can map MIDI CC, note, gate, and other parameters to knobs and jacks.ExpandersThere are lots of ways to customize your MetaModule. A Wifi expander allows you to wirelessly transfer patches from your computer. Add eight more knobs with the Knob expander, or buttons with the Button expander. A CV/Audio expander adds more high-resolution inputs and outputs, and the Gate In/Out expander adds not only gate jacks but also TRS MIDI and I2C.Under the HoodThere are six CV/Audio inputs, two gate inputs, and six CV/Audio outputs. The CV/Audio jacks are all 24-bit, 48kHz DC-coupled, -10V to +10V. A USB-C jack accepts MIDI devices and thumb drives. Patches and plugins can be loaded via a USB drive or microSD Card, and internal flash memory lets you save patches you always want to come back to.The processor is more advanced than anything 4ms has used in the past, and is among the most powerful processors found in Eurorack. Startup time and latency are blazingly fast.Features:Patches• Patches are loaded from microSD Card, USB drive, or via the Wifi expander• Patches can be optionally saved onto internal flash memory• Create patches using VCV Rack or directly on MetaModule• Patches can be given a name and descriptionMappings• Map each physical knob to up to 8 virtual knobs• Set range and offset for each mapping, including inverted control• Knob mappings are grouped into Knob Sets, and changing Knob Sets can be done quickly without menu-diving• Map physical jacks to virtual jacks, seamlessly making splits/mults• Add or edit modules, cables, and mappings in real-time while the patch is playing• Create alias names for mappings like "Kick Drum Level"Interface• Simple, intuitive graphical interface lets you zoom in on details, or zoom out to get a big picture• Patch View displays the patch as faceplates and cables, with knobs, buttons, and lights animating in real-time• Knob Set View simplifies the display, showing only the mapped knobs for the current Knob Set• Module View shows just one module and lists the names of each jack, knob, and control legibly• Mapping View lets you adjust details of a knob mapping• Adjust styles and visual preferences to your liking• Save, rename, duplicate, and delete patches• Firmware updater and plugin loader read from microSD Card or USB driveHardware• 12 Knobs• 8 CV/Audio outputs, 24-bit 48kHz, -10V to +10V, DC-coupled• 6 CV/Audio inputs, 24-bit 48kHz, -10V to +10V, DC-coupled• 2 Gate inputs• USB-C jack: MIDI Host or MSC (External drive) Host• microSD Card slot• Internal Flash RAM for additional patch storage• Dual-core 800MHz Cortex-A7 plus Cortex-M4 co-processor• 512MB DDR3 533MHz RAM• Bare-metal operation for fast startup and low latencyDIY-Kit-Type:Assembled unit. This is completely ready to use, nothing to solder or to assemble.
€649.00*
4ms - Pingable Envelope Generator (Black)
only 1 left
The Pingable Envelope Generator (PEG) from 4ms is a dual envelope generator whose envelope lengths are set by incoming clocks or "pings".The PEG has full CV control of envelope shape, skew, and ping (clock) division/multiplication, as well as a plethora of triggering and cycling options (AD, AR, quantization, cycle), and a tap tempo button for each channel.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€215.39*
4ms - Pingable Envelope Generator (Silver)
sold out at the moment
The Pingable Envelope Generator (PEG) from 4ms is a dual envelope generator whose envelope lengths are set by incoming clocks or "pings".The PEG has full CV control of envelope shape, skew, and ping (clock) division/multiplication, as well as a plethora of triggering and cycling options (AD, AR, quantization, cycle), and a tap tempo button for each channel.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€215.39*
4ms - Quad Pingable LFO (Black)
available
The Quad Pingable LFO (QPLFO) is a compact, playable four-channel tap-tempo, clock-syncable LFO with variable skew and reset.The QPLFO is designed to be useful in small portable systems that require maximum functionality in minimal space, as well as large systems that need maximum modulation sources.Features:• Quad "pingable" LFO's -- frequency is set by time between pulses ("ping")• Each of the 4 channels is an independent LFO• Can produce a variety of waveshapes: "Pluck," to ramp-down, to triangle, to ramp-up, and all shapes in between• Channels can easily modulate, trigger, and reset each other for complex and slowly morphing outputs• Slowest period is about 71 minutes (0.0002 Hz), fastest speed is about 500Hz (marginal tracking up to 1kHz)• Tap tempo button is free-running (LFO runs indefinitely), but external clock/Ping is auto-stopping (LFO stops when external clock stops)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€204.68*
4ms - Quad Pingable LFO (Silver)
only 1 left
The Quad Pingable LFO (QPLFO) is a compact, playable four-channel tap-tempo, clock-syncable LFO with variable skew and reset.The QPLFO is designed to be useful in small portable systems that require maximum functionality in minimal space, as well as large systems that need maximum modulation sources.Features:• Quad "pingable" LFO's -- frequency is set by time between pulses ("ping")• Each of the 4 channels is an independent LFO• Can produce a variety of waveshapes: "Pluck," to ramp-down, to triangle, to ramp-up, and all shapes in between• Channels can easily modulate, trigger, and reset each other for complex and slowly morphing outputs• Slowest period is about 71 minutes (0.0002 Hz), fastest speed is about 500Hz (marginal tracking up to 1kHz)• Tap tempo button is free-running (LFO runs indefinitely), but external clock/Ping is auto-stopping (LFO stops when external clock stops)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€204.68*
ADDAC System - 307 Heart Sensing
sold out at the moment
Another addition to our ADDAC300’s Expressive Controls Series.Preceded by the release of our ADDAC303 Muscle Sensing module this is the second module we make to take advantage of the physical body as a control source.This module originated from a simple idea: using one’s heart beat as a control source.Using a clip-on sensor, that can be attached to a finger or an ear lobe, the user’s heart rate will be acquired by sensing the blood flow passing under the sensor. This pulse will generate a trigger and an AD envelope.Clip-on sensor will be provided with the module.Features:• 0 +5v Trigger output• 0 +10v Envelope output with:• Attack, Decay, Amplitude and Offset controls• Two leds monitor the Trigger and Envelope OutputsDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€130.90*
ADDAC System - 701 VC Oscillator V2
available
This is our new VCO; we discontinued our ADDAC701 VCO a few years back and since then we’ve been wanting to release a more stable version with better pitch tracking, increasing pitch reliability, and further minimizing the detuning issues of analog VCO’s.For this new revision we chose to use the modern version of the CEM3340 ic from CoolAudio and add the triangle to sine circuitry of our previous VCO. This new version is extremely stable over 7 octaves.We also added a new Mix section which allows mixing of all waveforms controlled by 3 knobs SIN/TRI, MIX and SAW/RECT.Features:• Frequency knob with 6 octave range• Fine Tune knob with 12 semitone range• Octave switch with 6 octave range• 1v/octave cv input• Linear FM cv input with attenuator• LFO/VCO switch sets overall frequency range• Soft/Off/Hard Sync switch• Pulse Width control with initial knob and cv input with attenuator• SINE, TRIANGLE, SAW and PULSE outputs• Mix output controlled by 3 knobs SIN/TRI, MIX and SAW/RECT.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€158.00*
AF Labs - MI Marbles (PCB)
available
Features:Master clock• Internal clock with adjustable rate (with V/O CV input), or division/multiplication of an external clock.• Range selection button further multiplying or dividing the clock by 4.• Rhythm follower/predictor to lock onto uneven clock divisions or rhythmic patterns.• Adjustable jitter (knob and CV), going from perfect tracking to completely erroneous – but always preserving the overall tempo.Two-channel random rhythm generator• Three gate outputs: t2 is the main output carrying the jittery clock, t1 and t3 are the complementary random rhythm output.• Three generative models, with CV-controlled bias parameter increasing the density of notes on one channel or the other:• Random routing of each clock pulse to either outputs, following a coin toss.• Selection of a random division factor for one output, and the reciprocal factor for the other.• Generation of random kick/snare patterns using a process similar to Grids.• Adjustable gate duration, from short triggers to full length. Gate duration can be randomized.Random voltage generator• 3 outputs, either clocked by the 3 outputs of the random gate generator, or by a common external clock.• Distribution control: SPREAD control, scanning between constant, bell-shaped, uniform or discrete distributions; and BIAS control biasing the generated voltage towards the bottom or top of the voltage range.• Adjustable range: 0 to +2V (for melodies), 0 to +5V, -5V to +5V.Quantized or smooth... CV Post-processor• The STEPS parameter controls the steppiness/quantization of the output voltages.• Turn this knob clockwise and a progressive quantizer is applied to the voltages - progressively reducing the probability of hitting a note outside of the scale, then making accidentals less likely, then giving more weight to the root and fifth - and at the extreme yielding only octaves.• If steppy is not your thing, turn counterclockwise to increasingly slew the output voltages to the point that the module produces smooth, continuous curves.Programmable quantizer• 6 programmable scales.• Scales are programmed by playing a short jam in the target scale: Marbles learns which notes are more prominent than others.Output diversity• The three outputs can all follow the settings dialed on the control panel, or react in different and opposite ways. The turn of a knob can completely push your patch towards a new direction!Random looping and shuffling• DEJA VU parameter increasing the probably of re-playing past material to the point that the generated output forms a loop... then increasing the probability of randomizing the order of this loop.• The DEJA VU control applies to the random rhythm, the random voltages, or to both, or neither of them.• Adjustable loop length from 1 to 16 steps.External CV processing• An external CV can be recorded in the DEJA VU loop in place of internal random voltages.• All transformations performed by the random voltage generator (looping, shuffling, spreading, transposition, quantization, lag-processing) can be performed on external voltages.• TLDR: live remixing of external sequences!DIY-Kit-Type:PCB only Kit. This is a do-it-yourself PCB kit, no parts or Panel are supplied, you will need to source them yourself.
€8.90*
AF Labs - MI Peaks (PCB)
available
Features:Four in one...ADSR envelope generator• Segment durations ranging from 0.2ms to 8s.• Quartic attack, exponential decay, exponential release.LFO and tap-tempo LFO• 0.03 Hz to 160 Hz.• 5 basic waveforms: square, triangle, sine, stepped, random.• Waveform variations and morphing for each of these: PWM, slope, folding/harmonics, step size, interpolation.• Phase at reset control.• Tap LFO can lock onto irregular rhythms.Drum synth• Channel 1: 808 kick model with extra parameters (tune, punch).• Channel 2: 808 snare model with extra parameters (tune, decay).• Channel 2: A specific combination of settings transform the snare into a modelled 808 hi-hat.Control modes• Twin: Channel 1&2 share the same parameters but can be triggered independently.• Split: Channel 1 is edited by knobs 1&2, channel 2 edited by knobs 3&4, with a simplified 2-parameter control scheme.• Expert: Channel 1&2 are completely independent.DIY-Kit-Type:PCB only Kit. This is a do-it-yourself PCB kit, no parts or Panel are supplied, you will need to source them yourself.
€7.90*
AF Labs - MI Stages (PCB)
available
Features:Flexible input/output layoutThe module detects the presence of jacks on its gate inputs to group its segments: whether it is configured as a complex 6-stage envelope, or 6 individual envelopes, or 3+3, 2+4... depends simply on how you patch it. Dummy patch cables might come handy!When used as a multi-segment envelope, a segment activation signal is produced on all secondary outputs - for example to trigger an external event when an ADSR envelope enters its decay, sustain or release stages.In case more than 6 segments are required, up to six modules can be chained together thanks to a connector at the back of the module.Three segment types• Ramp segments go from one voltage to another, in a CV-controlled amount of time, with an adjustable curve (accelerating, uniform, decelerating). They are the building block used for the attack, decay or release segments in envelopes... or for LFOs.• Hold segments stay at a constant (but CV-controllable) voltage for a programmable amount of time. They serve as the sustain or hold segments in envelopes.• Step segments glide to a target (CV-controllable) voltage, then stay at this voltage for a certain amount of time until a trigger is received. They are the main ingredient for step sequences, but also for building sequential switches or a sample-and-hold.LoopingA segment, or a group of segments, can loop on itself: if the last segment of the envelope is included in the loop, the loop lasts forever. Otherwise, the loop remains active while the gate is high, then continues past the last segment of the loop. These two behaviors allow the creation of self-looping envelopes (LFOs), or the sustain stage of a good old ADSR envelope!Single segment processingEven when they aren't part of any group and don't receive any gate or trigger signals, individual segments can perform interesting functions: Ramp can loop on itself and turn into an LFO, Hold can delay a CV and Step can slew it.Now patch a trigger signal: the self-looping Ramp turns into a tempo-synced LFO, the Hold segment becomes a pulse generator, the Step segment a sample-and-hold.DIY-Kit-Type:PCB only Kit. This is a do-it-yourself PCB kit, no parts or Panel are supplied, you will need to source them yourself.
€7.90*
AF Labs - MI Tides v2 (PCB)
available
Features:Digital function generator• 3 operating mode: AD envelope, looping (VC-LFO/VCDO), AR envelope.• 3 frequency ranges for the main frequency knob: low (2 minutes to 2 Hz), medium (0.125 Hz to 32 Hz), high (8 Hz to 2kHz). This range can be widened by applying an offset on the V/OCT input.A large palette of waveforms• Shape control with CV input – covering various combinations of linear, exponential, or sinusoidal segments.• Slope/asymmetry (A/D time ratio) control with CV input.• Smoothness control with CV input: smoothes the waveform using a 2-pole digital filter, or adds bumps and kinks with a digital wavefolder.External clocking/PLL• The module can use an external clock or clean audio signal as a reference, and operate at a multiple of this clock (from 1/16 to 16x).• This allows, for example, the generation of (sub)harmonics from another VCO.4 output modes• Different shapes. Each output produces a different waveshape: main signal (with voltage-controlled attenuverter), raw asymmetric triangle, end of attack gate, end of release gate.• Different amplitudes: Voltage-controlled dispatching of the signal to each of the 4 outputs.• Different times: Voltage-controlled phase or apex shifting of the signal.• Different frequencies: Outputs 2, 3, and 4 are shifted up or down in frequency relatively to output 1, creating chords or polyrhythmic LFOs.DIY-Kit-Type:PCB only Kit. This is a do-it-yourself PCB kit, no parts or Panel are supplied, you will need to source them yourself.
€7.90*
AI Synthesis - Looping ADSR Envelope Generator
sold out at the moment
The AI002 DIY Mixer Kit is an updated take on a classic utility audio or cv mixer. All three inputs have a level control, with full clockwise allowing full volume prior to the summing mixer. Perfect for adding audio inputs to a filter, or cv inputs to a cv input, and other mixing functions. This kit is ideal for those who know how to solder, but are still starting out in their DIY Synthesis journey.This diy mixer kit will not only familiarize yourself with IC Chips, Capacitors, and Resistors, it will also add a key utility module to your DIY Modular Synthesizer.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€87.00*
Apollo View - Allscillator
only 2 left
This advanced 10HP analog VCO/LFO based on the 3340 IC offers extreme stability, wide frequency range (0.0011 Hz–20 kHz), and eight simultaneous waveforms—including unique PWM Saw and deep Sub Pulse outputs. It supports both exponential and linear FM, three sync types at once, and precise tuning controls. With modes for audio, LFO, and ultra-slow modulation, it’s a powerful all-in-one oscillator designed for creative flexibility and technical precision.Features:• 1V/oct tracking over +10 octaves• Eight simultaneously available waveforms• Unique PWM Saw• Sub Pulse waveform (-1 octave, -2 octave, -2* octave)• Audio / LFO / Ultra LFO modes (up to 15 mins)• Exponential Frequency Modulation• Linear Frequency Modulation• Exp FM and Lin FM simultaneously available• Positive edge Hard Sync• Negative edge Hard Sync• Soft Sync• 3 Sync types simultaneously available• Coarse Knob sweeps 5 octaves in Audio mode• Fine Knob sweeps -+5 semitones in Audio mode• Extremely stable across all temperaturesDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€300.00*
AtoVproject - cLFO
available
Introducing our innovative Complex Low Frequency Oscillator (cLFO) - The cLFO is an instrument for those who believe in pushing the limits of modulation. Featuring two CV-controlled LFOs that intricately intermodulate and are seamlessly integrated with a ring modulator, this module elevates your synthesis and sound design to unprecedented levels.Crafted with a focus on cross and self-patching, the cLFO invites you to explore the endless possibilities of modulation. Dive into creating continuously variable waveforms, exponential shapes, bouncing ball effects, immersive stereo soundscapes and many other sonic wonders!Each LFO outputs Triangle, Saw, and Square waves. The Triangle output of LFO1 is normalled to the CV input of LFO2 with attenuation. The addition of a ring modulator to this setup draws from years of the designer's own experimental projects. It is an invitation to experiment with effects traditionally reserved for audio in the realm of modulation. A ring modulated LFO delivers the rhythmical essence of a conventional LFOs but with an added complexity and variability that ensures your soundscapes are always evolving.This module offers an expansive modulation frequency range, with speed adjustments from as slow as 2 minutes per cycle to as fast as 20 cycles per second. With CV control, frequencies can stretch from 13 hours per cycle to 400 cycles per second, ensuring unparalleled versatility in your modulation explorations.Accompanying the cLFO is a detailed manual filled with lots of patch idea designed to elevate your sound design skills to new levels.Dive into the world of advanced modulation manipulation with cLFO.Stay inspired! Stay innovative!Features:• Two analog LFOs• Control voltage over LFO frequency• 3 waveform outputs per LFO: Triangle, Square and Sawtooth (LFO1 - ramp down; LFO2 ramp up)• Wide frequency range: 2 minutes - 0.05s (20Hz) without CV and 13 hours to 400Hz with CV• Ring Modulator (aka four quadrant multiplier aka bipolar VCA)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€190.00*
AtoVproject - Faderpunk (Assembled)
available
NO DIY – THIS UNIT IS FULLY ASSEMBLEDFaderpunk is a modular, customizable modulation ecosystem for Eurorack and semi-modular setups. Built around six tactile faders and channelized app-driven firmware, Faderpunk turns empty jacks into dynamic modulation sources, MIDI bridges and performance tools. Run multiple apps at once – LFOs, sequencers, envelopes, quantizers, Turing machines, CV-to-MIDI and MIDI-to-CV converters, random generators and rhythm engines – then reconfigure the system instantly with the web-based app manager. Deep integration with MIDI and CV means Faderpunk speaks both languages fluently, letting you combine hardware and software workflows to create hybrid modulation rigs that are playable, programmable and uniquely yours.A browser configurator (connect Faderpunk to a computer and visit the web interface) makes app management drag-and-drop simple, while a developer-friendly API lets you build custom apps and extend the platform. Physical customization includes a set of stickers for control labelling and configurable RGB LEDs for visual feedback, giving you immediate, readable state information during performance. Compact, hands-on and open, Faderpunk is a versatile modulation hub for live rigs, studios and DIY instrument projects.Features:• Modulation platform: run LFOs, sequencers, envelopes, randomizers, quantizers, Turing machines and more.• Hybrid MIDI + CV workflows: MIDI-to-CV and CV-to-MIDI bridging for seamless hardware/software integration.• 16 channels comprised of: CV jack configurable as Input or Output (0-5V, 0-10V or +/-5V range) and a Mechanical RGB backlit button • Web-based configurator with drag-and-drop app management (connect device to your computer to access).• Developer API for creating custom apps and extending functionality.• Configurable RGB LEDs for clear visual feedback and live performance cues.• Sticker set for personalized control labeling and ergonomic mapping.• Ideal as a modulation source, sequencer, MIDI bridge or performance controller in Eurorack and semi-modular systems.
€649.00*
Befaco - Pony VCO
available
Analog Thru-Zero Wavefolding VCO/LFOPony VCO is a fully analog Thru-Zero oscillator with wavefolder and dedicated VCA in only 4HP. The module offers great stability and tuning capabilities thanks to its powerful core, based on Sound Semiconductors IC. It comes with range selector, that allows it to go down to LFO range, as well as octave and waveform selectors.In Through Zero oscillators, frequency is controlled by either positive and negative voltage. If FM CV goes below zero, the core will continue oscillating inverting its phase. This “little” change of behaviour allows the core to create a whole new range of timbres that are just impossible to achieve with regular VCOs. If you set the module as LFO, the range of funky modulations will be endless!There is a separate panel for conversion to 1U available. You can use the 1U panel with the normal 3U module, but have to buy it additionally and you have to make some changes by soldering a hand full of SMD parts, but it's quite easy. 1U format keeping the same functionality and control layout.In Through Zero oscillators, frequency is controlled by either positive and negative voltage. If FM CV goes below zero, the core will continue oscillating inverting its phase. This “little” change of behaviour allows the core to create a whole new range of timbres that are just impossible to achieve with regular VCOs.If you set the module as LFO, the range of funky modulations will be endless!Features:• Through Zero Frequency Modulation• Wavefolding (Timbre)• Pulsewidth Modulation (PWM)• SYNC• VCA• LFODIY-Kit-Type:Semi-DIY-Kit. Most of the components are completely ready, you only have to assemble panel, knobs and some screws/washers.
€177.31*