Various Parts

Befaco - Bananuts

available

Bananuts are anodized alluminium custom minijack nuts, following Buchla/Serge coloring code.Perfect to code your inputs and outputs with colors or just give a touch of beauty to your favorite gear. One bag contains 25 pcs.Compatible Jacks:• PJ301M-12 (Thonkiconn)• PJ398SM (Thonkiconn)• PJ366ST (Green Stereo Thonkiconn)• PJ301BM• PJ398S-BM• PJ301CM• PJ302M• 161-3502L-E (Kobiconn)Features:• Eight colors available following the Buchla/Serge color code: Blue, Purple, Red, Orange, Yellow, White (actually silver), Green and Black.• Anodized Aluminium• 1 bag = 25 pcs.

€9.20*

Details

Electrosmith - Daisy Seed

available

Daisy is an embedded music platform that provides everything needed to build high-fidelity audio hardware:Plug in a USB cable to power the board and start making sound, upload an example program over USB, and tweak it in real time. Firmware developed for Daisy is released free under a permissive open-source licence, and the platform is programmable in C++, Arduino, Max/MSP Gen~ and Pure Data.Hardware highlights include stereo audio I/O at 96 kHz / 24-bit (AC-coupled), an ARM Cortex-M7 MCU running at 480 MHz, 64 MB of SDRAM (enough for up to 10-minute audio buffers), 8 MB of external flash, an SD-card interface, 31 GPIOs, 12 16-bit ADC inputs, 2 12-bit DC-coupled DAC outputs, PWM outputs and common serial buses (SPI, UART, SAI/I2S, I2C), plus a dedicated VIN pin for external power – everything you need for complex, standalone audio devices.Features:• Stereo audio I/O – 96 kHz / 24-bit audio hardware (AC-coupled)• Programmable in: C++, Arduino, Max/MSP Gen~, Pure Data• ×31 GPIO, ×12 ADC inputs (16-bit), ×2 DAC outputs (12-bit, DC-coupled)• ARM Cortex-M7 MCU running at 480 MHz• 64 MB of SDRAM for up to 10-minute audio buffers, 8 MB external flash• SD-card interface, PWM outputs, and various serial protocols for external devices (SPI, UART, SAI/I2S, I2C)• Dedicated VIN pin for external power

€42.00*

Details

LeafAudio - Raised Thumb Screw Set

available

A set of 4x raised thumb screw M3 x 0,5 (20mm length including a spacer) for Microphonic Soundbox, Microphonic Playground and many other applications.

€6.50*

Murata - Piezoceramic Transducer

available

Piezoceramic transducer by Murata. You can use it to build your own contact microphone or pressure sensor for your modular synth etc. ø 27mm, impedance ~200Ω, resonance frequency 4,6 ± 0.5 kHz.Among many, we picked this one, as it sounds crisp and beefy

€2.39*

Screw M3 6mm length, Dome Head, PH Drive (10 pcs)

available

The M3 x 0.5 screw (6mm thread length) is normally used to connect Eurorack modules and rails.These are supplied in packs of 10.

€0.49*

Screw M5 20mm length, Countersunk Head, PH Drive

available

M5 screw (20mm thread length), DIN 965 countersunk head PH drive.For connecting side-parts of your case and rails.

€0.19*

Screw M5 20mm length, Raised Countersunk Head, PH Drive

available

M5 screw (20mm thread length), DIN 966 raised countersunk head PH drive.For connecting side-parts of your case and rails without side-brackets.Mix between countersunk and dome head, sinks in about 50%.

€0.19*

Screw M5 25mm length, Self Carving Countersunk, Torx Drive

sold out at the moment

Self-tapping M5 screw (25mm thread length), DIN 7516 countersunk head Torx drive (TX25).Recommended screw for connecting side-brackets to our rails.

€0.20*

Details

Screw M5 30mm length, Countersunk Head, PH Drive

available

M5 screw (30mm thread length), DIN 965 countersunk head PH (Phillips) drive.For connecting side-parts of your case and rails.

€0.22*

Screw M5 30mm length, Dome Head, PH Drive

available

M5 screw (30mm thread length), DIN 7985 dome head PH drive.For connecting side-parts of your case and rails without side-brackets.

€0.22*

Screw M5 30mm length, Raised Countersunk Head, PH Drive

available

M3 screw (30mm thread length), DIN 966 raised countersunk head PH drive.For connecting side-parts of your case and rails without side-brackets.Mix between countersunk and dome head, sinks in about 50%.

€0.22*

Washers

available

These washers are suitable for Thonkiconn and similar 3.5 mm audio connectors. They provide a secure fit and reliable spacing for your DIY synthesizer and audio projects.• Available in: Bags of 20 or 50 pieces (please select your preferred quantity above).• Measurements: 6.1 mm × 8.5 mm × 0.5 mm.

€1.10*

Details

Filter products