Filter
333modules - VCA4Mix

sold out at the moment

Four channel VCA and mixer based on the classic LM13700 OTA. The perfect tool for your generative patches thanks to its linear response. Up to 5 signals can be mixed with the additional auxiliar input.Features:• Classic LM13700 OTA• Two sections philosophy. One IN signal to two CV VCAs (disconnection)• Mixer 5 signalsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€107.10*
ADDAC System - 107 Acid Source

only 2 left

We started this module with the idea of developing a complex drum source. However, somewhere along the process we noticed how much better it performed as a synth voice and simply embraced this lucky accident.It features a VCO with a [FREQUENCY] and [FINE TUNE] knob plus a dedicated CV Input and Attenuator knob (tunable over 4 octaves). The VCO waveform output is achieved by selecting either a Triangle or Saw through a switch. The selected waveform can then be mixed/balanced against the square wave. The resulting mix is then sent to the Filter.The Filter features a [CUTOFF] and [RESO] resonance knob plus a Cutoff CV Input and Attenuverter knob.A 3 position switch is used to select the filter type: Highpass, Bandpass or Lowpass. The resulting output is then sent to the VCA.The VCA features an Input with [INPUT GAIN] knob which at maximum can amplify the incoming signal by a factor of 2.This is a very important control, it accepts any signal Trigger, Gate or CV. Whatever input is plugged in the signal is then fed through an AD with a very short attack and controllable decay through the [VCA DECAY] knob plus the CV Input and Attenuverter knob. The resulting slewed signal is then used to control the VCA gain. This signal is also sent to the CV OUTPUT as well as the LED monitor.The Accent input adds to the Input signal creating a different amplitude output. The CV OUTPUT is normalled to the Frequency and Cutoff inputs.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€202.30*
ADDAC System - 805 VC Signal Router V2

available

Inspired by our ADDAC701 VCO waveform mixing section, our new VC Signal Router also updates our legacy X-Fade/Panner to a stereo configuration that also allows 4 quadrant mixing.Featuring two dedicated X-faders and a stereo VCA that can also be used as a third X-Fader. All controls have their own CV inputs and dedicated Attenuverters for precision control.4 quadrant mixing is achieved by using the stereo Master as a X-fader between left and right channels, this way you can plug 4 audio sources and sweep/crossfade between each and any of them using the 3 x-faders. Plug any 4 sources (4 waveforms of a VCO, 4 LFOs, 4 envelopes...) and sweep through morph through or have them all mixed together.For other configuration types Left and Right X-fader channels can be routed through the Master stereo VCA or sent directly to the outputs. A stereo Direct input can also be routed through the Master VCA or sent straight to the outputs.The Mono Sum output always mix Left and Right outputs together allowing the possibility to use the module as a peculiar 6 channel mono mixer.It can be used for both Audio or CV Signals.Features:• 6 mono inputs• 2 dedicated X-faders with Control knob + CV Input and Attenuverter Each X-fader can be routed through the Master mix or straight into the outputs.• Master channel can be used as a stereo VCA or an X-fader• Stereo direct inputs can be routed through the Master mix or straight into the outputs.• Fully analog audio path with high quality/low noise VCAs.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€168.98*
Apollo View - Curiouser

available

6 HP expander for Rabbit Hole. Provides 2 additional input channels. Each channel can either be sent to Rabbit Hole or used as a standalone VCA. When used standalone, the two channels are normalled to sum at the bottom output. Gain CV is normalled from Rabbit Hole.Features:• Expander for Rabbit Hole• 2 inputs with vintage character OTA VCA• Each channel can be used as a standalone VCA• Attenuverters for CV inputs• All analogue signal pathDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€123.76*
Apollo View - Rabbit Hole

available

16 HP summing mixer with characterful valve saturation & distortion. Rabbit Hole is a hybrid solid-state and vacuum tube design. It has two input channels with independent vintage VCAs. The outputs of the VCAs are summed and passed to a solid-state Drive circuit which at higher gain settings hard clips the signal before entering the starved cathode dual-triode vacuum tube. The OWTH - Off With Their Heads diode LED clipping circuit can be engaged for further distortion.Features:• 2 channel mixer with vintage character OTA per input VCAs• 12AU7 Vacuum Tube Core• Fat sounding all analogue signal path• 4 possible stages of distortion• Tone shaping with CV control• Dry/Wet Mix with CV control• Feedback with CV control• Attenuverters on all CV inputs• Switchable diode clipping circuit “OWTH - Off With Their Heads”• “L8” Switch to change Tube characterDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€276.08*
AtoVproject - cDVCA (Black)

available

cDVCA or class-D VCA is a new kind of VCA based on an entirely novel concept that is inspired from class-D amplification technology. This is not a transparent VCA and brings a lot of character to the sound.The first VCA that tracks 1V/octConcept: The input signal is turned into an ultrasonic PWM signal (~34kHz). The PWM is scaled to the desired amplitude and then filtered back down to the original signal.The twist: The PWM frequency can be lowered down into the audio spectrum and the frequency can be controlled via its 1V/oct input allowing for crazy waveshaping that tracks your melodies.The drive controls an innovative clipping method that does not rely on overdriving any circuitry and therefore results in distortions with a very defined character.The signal then goes into a 1 pole VCF/tone circuit that allows to keep things under some amount of control as the harmonics produced by this module can be very aggressive.With no input the module generates a simple square wave and therefore can be used a simple synth voice (VCO→VCA-VCF)DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€185.00*
Befaco - A*B+C

sold out at the moment

A*B+C is a dual, four-quadrant multiplier with VC Offset that can act as Dual Ring Modulator, Dual VCA and Four Channel Mixer. Each section can perform the analog multiplication of two signals (A and B) and add an offset (C).Features:• Dual-channel bipolar VCA’s• Adjustable VC Offset per channel.• AM and Ring Modulation capabilities.• Output allows it to work as a four-channel mixer.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€107.10*
Befaco - Hexmix VCA

only 2 left

Hexmix VCA is a compact six channel VCA with an unique response curve range from logarithmic to linear and to exponential using a pot.All outputs are routed to output six to act as a mixer, with a normalization of each one to remove each channel from the Mix.The module can act as six independent VCAs as well as a Mixer for all the inputs (Selectable via a switch).Every VCA has a response pot for the incoming CV, being full logarithmic at maximum setup and full exponential at minimum setup, having the linear response in the center position.Level pot of each channel is an attenuator of the signal coming out of each VCA.Jacks are normalled to 10 volts, so when we have no CV present VCA would be fully open and our Level pot will act as a volume.Features:• 6 channel VCA• Linear, exponential and logarithmic response.• Selectable mixer function.• Expander connection to plug every channel of an Hexmix VCA directly.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€195.16*
Befaco - Lich

sold out at the moment

Lich is a programmable multi-function module based in the Rebel Technology OWL platform that allows you to use Pure Data, Max Gen or Faust code into your module!.Lich is a Befaco Rebel collaboration that brings back Owl’s platform with this new hardware iteration. It has stereo in and out, four pot controls summed to cv inputs (like the classic Owl module) And as addition, CV and Gate outputs, patch selection with display and USB MIDI host and device connections.Features:• Stereo Audio IN and OUT at 48k 24 bits.• 4 CV controls (Pot + Attenuated CV in)• 2 CV outputs.• 2 Gate intputs + buttons.• 1 Gate Output.• Patch selection and visialization via display.• USB host and Device connectionsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€201.11*
Befaco - Percall

only 2 left

Percall is a percussive oriented module that will shape four different sound sources into percussive sounds. Percall has four VCAs with dedicated decay envelopes and a mixer, so you can prepare a percussion submix. Added strength input will provide extra dynamics to the sounds! To round up the module, audio inputs are normaled from one to two and from three to four, spicing them up with choke control. This allow to create open and closed Hats or kind of side-chained baselines with your kick.Features:• Four VCAs with dedicated decay envelope.• CV control over envelope decays.• Individual outputs for each envelope• Volume control per channel and normaled Mix out.• Strenght input affecting all four channels.• Audio Input 1 normaled to Input 2. Audio input 3 normaled to input 4.• Choke contrrols, binding Channel one with two and three with four.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€165.41*
Befaco / Divkid - Stereo Strip

sold out at the moment

Stereo Strip takes the idea of a channel strip and makes it modular. We hope that by bringing this long-established component of the audio engineering world into the Eurorack environment and by adding CV control over its key parameters that you will find new, creative ways to use it in your patches!It features stereo inputs and outputs for audio or CV with EQ, voltage controlled panning, stereo VCA, performable mute and input/output level switching for Eurorack or line level uses. Abusing the input level switching allows for some musical, modulate-able and highly shapeable distortion sounds too.Stereo Strip was designed to be a creative part of a modular patch. Creating stereo images from mono sources, shaping and modulating existing stereo images, synthesising stereo pseudo ring modulation, sweetening FX with EQ or drastically wave shaping your oscillators, creating send FX routings with benefits or it can simply be used as a channel strip at the end of chain in a patch.The addition of line level gain boosting (for the input) or reduction (for the output) allow it to work as a stereo input or output interface for external gear with the advantage of the VCA, panning and the EQ to shape the sound. Experiment with bringing external gear into the Eurorack format and then shape and modulate those sounds them on the way in!Try patching Stereo Strip anywhere you would place a VCA in a system and/or explore its EQ and voltage controlled panning, which are rarer additions to the sound sculpting options for the Eurorack format.This module is designed in collaboration with Ben Wilson aka Divkid.Features:• 3 band EQ• Panning (manual and voltage controlled)• VCA level control (manual or voltage controlled)• 3 way performance muting (on-off-momentary)• Soft clipping limiter (distortion!)• Line level input and/or output adjustmentDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€117.81*
CubuSynth - Dual Vintage VCA

available

The CubuSynth Dual Vintage VCA is a nice sounding, zero bleed, analog Voltage controlled amplifier based on the LM13700 chip.It can work as two independent VCAs or as a stereo unit, and CV input 1 on channel 1 is normalized to the CV input 1 on channel 2. (same signal can control both channels).Features:• LEVEL Knobs set the Amplitude for each channel• CV AMOUNT Attenuators for the Control voltage from CV input 1• Second CV input per channel, without attenuatorDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€56.17*
CubuSynth - VCFA

only 1 left

The CubuSynth VCFA is a multimode VCF with LP,HP and BP modes with integrated VCA, CV control over frequency, resonance and volume. The CV input for the frequency features 1V/Oct scaling over about 2~3 octaves. So you can even create plucky melodies with the resonance in "ringing" mode. The gain control can reach a nice, soft saturation.Features:• 3 simultaneous Outputs for Low Pass, Band Pass and High Pass• Integrated VCA at the input stage• CV control over volume, frequency and resonance• "Ringing" mode on upper resonance setting• 1 V/oct tracking over 2~3 octaves (with freq CV attenuator on 100%)• Saturation on incoming signal (VCA stage) on upper gain settingDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€85.68*
Dannysound - MM VCA

available

The M.M. VCA is a 6HP Eurorack VCA module based on the classic design by Dr. Robert Moog as used in his first portable synthesiser.The discreet design of the circuit has inherent soft clipping characteristics when driven, which either add harmonics to a pure sine wave orconversely remove higher order harmonics when amplifying waves such as a Saw or Triangle.This has the effect of slightly boosting the fundamental frequency, making sounds that are fatter and warmer than standard VCAs.The M.M. VCA has two inputs with level controls – both inputs are then routed through two VCAs in series (PRE-AMP and MAIN AMP).This allows for modulation of the first VCA (PRE-AMP) with an LFO and the second (MAIN AMP) with an Envelope Generator.An offset control provides a DC control voltage to the first VCA that can be used to bias the modulation so it doesn’t cut offWhen the LFO is in the negative part of its cycle. This control should be set to full if modulation of the first VCA is not being utilised.Features:• 2 x Audio Input Level Controls – Starts soft clipping after approximately 50%.• CV 1 (PRE-AMP) Level – Adjusts the amount of CV to VCA 1.• CV 2 (MAIN AMP) Level – Adjusts the amount of CV to VCA 2 (Normalled to 10V).• CV 1 OFFSET Amount – Adjusts the amount of DC bias control voltage to VCA 1.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€151.73*
Erica Synths - EDU DIY VCA

only 2 left

This is an easy to build VCA with a really extensive documentation and explanation of the circuit. Excellent learning kit!mki x es.EDU VCA is a simple yet efficient dual VCA for your eurorack system. It has DC-coupled inputs so you can use the VCA both for audio and CV signals. Inputs of the second VCA are normalled to the first one which allows to split the audio signal to both VCA or control both VCAs with a single CV. A 60-page build manual explains the electronics behind the module and provides step-by-step build instructions.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€66.64*
Feedback Modules - VCA2600

sold out at the moment

VCA2600 needs no introduction. The best sounding VCA in 4HP with matched and thermo coupled transistors.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€52.36*
Herzlich Labs - Omen

available

The Omen is a dual LPG with a bit more than you might be used to. Like you, I once was lost in the world of low pass gates, seeking something more, something bigger and somehow juicier. The inspiration came to me as I was reading a particularly heavy book on passive filters, and I realized it was possible to make far more interesting LPG designs than the standard we've become so accustomed to.In a convergence of old-school LPG design and more modern components, the Omen boasts two -6dB resonant filters, custom built vactrols, built in CV attenuation and no less than three cutoff modes per filter. Filter 1 is soft and light, imparting a gentle, naturally gated touch of filtering on your sound, while Filter 2 is darker and more resonant, and can turn downright growly and distorted when left wide open.Designed to give you as many creative options as possible, the Omen has the unique ability to function as either two discrete LPG, or as one 4-pole resonant LPG. When plugging a signal in to Input 1, and with no signal plugged into Input 2, the output will be present at both Output 1 and Output 2, with Output 2 producing the signal as it passes through both filters. Tweaking both filters independently will generate a wide array of soft and sometimes harsh tones, ranging from Buchla bongos to early synthesis brass and organ sounds. There is much to love here.CV is similarly handled, by plugging in only one CV source, it will act on both channels - this is useful for creating musically similar outputs as well as when using the dual filter operation. However, the dual filter mode greatly benefits from having two CV inputs: use an envelope in CV1 to act as a VCA, and an LFO in CV2 to create tremolo, for instance.Using custom designed, hand built vactrols, care has been taken to mitigate the less desirable aspects of passive LPGs - in most modules, the user can expect zero bleed through on the LPG channels, and signal attenuation is minimal even with the 4-pole filter settings engaged. Of course, many of the natural features of vactrols remain, such as subtle memory effect when engaging the vactrol for long periods.DIY enthusiast? Rejoice! The Omen is available as a fully loaded DIY kit - everything you need to build your very own Omen packed in one place, so you can easily build one in the comfort of your own home. It is not a difficult DIY project, an ambitious beginner or someone with experience from a few easy builds can tackle the Omen in an afternoon. The build is all through-hole aside from three SMD components, which are easily soldered by hand due to their large size.Finally, you receive maximum blinkenlights as LED's on the front panel simulate the action of the vactrols, so you'll always know what's going on under the hood. No collection of fancy LPG's is complete without the Omen - add some analog warmth to your signals, today.Features:• Functions both as two discrete LPGs or as one multi-pole filter LPG• A passive LPG without the characteristic signal bleed or input loss• You read that right: each LPG contains a resonant two-pole filter• Comprehensive build guide, complete with picturesDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€83.06*
Jolin - Ashiko

available

Quad stereo VCA and panner.ASHIKO is a quad ping-pong VCA designed to create multi-directional stereo sounds starting with mono sources. When an output is linearly opening the other one is alternately closing following the behaviour of the CV source. Different kind of controls - pulses, envelopes, complex waves - will make the VCA react in a distinctive way.Features:• Four stereo full range VCAs.• Transistors based CV inputs designed to give the best results with LFOs.• Individual toggle switches to activate mono or stereo mode.• Selectable hard/soft switching curve.• Input and CV are normalled and they flow top to bottom when no jack is inserted.• Works with audio and CV sources.• “Whatever” power connector a.k.a. don’t mind the polarity.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€153.51*
Jolin - Tutto & Sempre

available

TUTTO&SEMPRE is a stereo performance mixer with 4 channel strips, an active patchbay, individual VCAs, clickless mutes, individual post attenuation direct outs, a main balanced stereo output and two high fidelity headphones drivers with switchable stereo inserts.Features:• Four channel stereo performance mixer.• Signal path optimized for the integration between modular systems and outboards.• Versatile mixing frame with an active patchbay, stereo attenuators, paired VCAs and clickless mutes.• Line level balanced L and R output + combined stereo with master auxiliary input.• Two independent headphones drivers with switchable individual stereo preview input.• “Whatever” power connector a.k.a. don’t mind the polarity.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€343.91*
MRG Synthesizer - VCA

sold out at the moment

The MRG VCA is a dual linear VCA module, based on the AS3360 (clone of the CEM3360).It's an extremely flexible module and can be used in a variety of ways.Both VCAs can be controlled by a CV entry, modulated by control knob.VCA1 also has an initial gain control (B1), that offsets the CV input by a constant value.This allows VCA1 to be left always open, with the initial gain controlling the amplification.If both input jacks are used (IN1, IN2), the two VCAs will operate independently.The output of VCA1 will go to OUT1, the output of VCA2 will go to OUT2.If there's no jack in IN2, the two VCAs will be cascaded, and the output of VCA1 will go both to OUT1 and as an input to VCA2.This allows this module to be used to process both the MIDI Velocity and the envelope of an audio signal.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€70.00*