Effects
available
Analog optocoupler filther.GOBLET is an analog filter and distortion unit with some added quirks and extra controls. Start with both faders - frequency and resonance - at maximum, turn the trimmers fully clockwise and set the feedback pot at 0. Now insert an input and take the output either from the lowpass out or the notch out. Start to turn the frequency trimmer until the resonance kicks in. Now adjust the resonance trimmer to your taste. The faders now have full range of responsiveness. Adjust the feedback and start the filthering. For extra distortion interact with the two touch plates and the central momentary button.Features:• Unique analog two pole circuit with custom optocouplers fed directly in the feedback path.• Two step controls and individual CV inputs on frequency and resonance for precise sound sculpting.• Dedicated potentiometer for the total amount of feedback.• A performance-oriented momentary switch for extra distortion.• Two expressive touch points to make your body interact with the circuit.• Rhythmically oriented accent CV input.• Two outputs - a smoother LP and an aggressive notch.• Works with audio and CV sources.• Single board design - extremely skiff friendly.• “Whatever” power connector a.k.a. don’t mind the polarity.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Farbfolder is an analog wavefolder for Eurorack, designed to add harmonically related overtones to an audio signal.We have always been fascinated with analogue effects circuits, and we love the way their quirks and nonlinearities inspire us to find new sounds.Farbfolder does this weird and wonderful trick of folding up the wave at the zero points, "squaring" a sine off with more and more sinusoid edges, thus adding odd harmonics.This module is excellent at adding rich harmonics to a basic waveform. Its circuit can produce characteristic timbres similar to pulse-width and frequency modulation.It is part of our Farbfilter (colour filter) range of sound colouring modules, offering a wide sonic palette from lending subtle colour to rich timbre bending tones in 4 HP.Farbfolder is designed to be an easy, beginner-friendly DIY build you can solder yourself.Features:• Classic analog West Coast circuit: odd harmonics Wavefolder.• Offset and Attenuation for Fold CV for flexible modulation.• Bias Folding: Offset Audio input with CV.• Push Bias into dead zone for VCA-like use.• Backlit panel offers instant visual feedback over CV.• Flip panel: with or without number.DIY-Kit-Type:Semi-DIY-Kit. Most of the components are completely ready, you only have to assemble panel, knobs and some screws/washers.
sold out at the moment
Farbshaper is a classic West Coast analog waveshaper for Eurorack, designed to shape the overtones of an audio signal with two voltage controlled stages.We have always been fascinated with analogue effects circuits, and we love the way their quirks and nonlinearities inspire us to find new sounds.Farbshaper is based on a classic circuit that turns a ramp into a sine, and was historically used in function generators and oscillators. On any other signal it will add one or multiple wave folds.The circuit produces opposite offsets internally, so the knob settings interact strongly and are fun to automate with CV.This module is excellent to use as a non-linear shaper for acoustic and electronic sounds, ranging from gentle timbral transformation to colourful wavefolding.It is part of our Farbfilter (colour filter) range of sound colouring modules, offering a wide sonic palette from lending subtle colour to rich timbre bending tones in 4 HP.Farbshaper is designed to be an easy, beginner-friendly DIY build you can solder yourself.Features:• Classic analog West Coast circuit: multi stage Waveshaper / -folder.• CV and Attenuation to control first single Fold stage.• CV and Attenuation to control Pleat, a second dual Fold stage.• Internal CV offset creates dead zones for VCA-like use.• Backlit panel offers instant visual feedback over CV.• Flip panel: with or without number.DIY-Kit-Type:Semi-DIY-Kit. Most of the components are completely ready, you only have to assemble panel, knobs and some screws/washers.
sold out at the moment
Tausend dB is a four channel amplifier module for Eurorack in 6HP, allowing you to boost Audio and CV.Tausend dB works great for bringing line signals to Eurorack levels, and saturating Eurorack levels into overdrive. We love feeding piezo signals into Eurorack with it.The module has pin headers in the back so you can break out from prototyping platforms like Arduino, Teensy, Daisy and Bela to Tausend dB's inputs with jumper wires.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The London Drive is a 4 HP Drive/Distortion module inspired by the prestigious EMS VCS3/Synthi input gain. London Drive has two inputs and two outputs. Output 2 is a reverse phase version of Output 1, with a slightly different sonic character as well. Unlike its sibling Mini Drive, the London Drive gain knob never goes completely silent, but instead ranges from a clean signal to warmly overdriven. The module works as a gritty drive for modular level signals and works well with line level inputs as well – like a drum machine. It’s not suited as an external input for guitar.Using this module is a great way to make a polite sound source into something less polite, but always experiment with the levels! – the output can sound completely different depending on the settings and it can also be used to just add a nice bit of warmth to your input. London Drive also works very well with feedback loops – the dual inputs and differently phased outputs are designed to encourage experimentation with feedback patching.While this module doesn’t have CV in, you can either put a VCA or a filter before to modify the amount of grime, or get more experimental and try blasting an LFO or a sequence into one input to see what it does to audio in the other input.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
The Mini Drive is a 4 HP Drive/Distortion module inspired by the classic Minimoog input gain. Mini Drive has two inputs which are higher and lower gain - but if you use both they’re the same level mixed. The Drive knob goes from zero/silent to lots of gain. It’s a dirty gain for modular level and works well with line level inputs – like a drum machine. It’s not suited as an external input for guitar.Using this module is a great way to make a polite sound source into something less polite, but always experiment with the levels! - the output can sound completely different depending on the settings and it can also be used to just add a nice bit of warmth to your input.Mini Drive also works very well in feedback loops. The classic minimoog trick is taking the audio output and adding it back after the oscillators, before the filter through this circuit. So the filter is in a feedback loop which will add resonance and fuzz. If you patch one output directly to an input then you can achieve feedback tones. Another idea is to patch sound (radio music, or a Osc/env/filt voice) into ‘low’ and one output to the main out. Then patch the second out to a filter, or a delay or reverb, and the output from that back into ‘high’ then turn up and add what happens. If the feedback isn’t wild, invert it with an attenuverter before going back into high.While it doesn’t have CV in you can either put a VCA or a filter before to modify the amount of grime, or get more experimental and try blasting an LFO or a sequence into one input to see what it does to audio in the other input. the outputs are passive multed together.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
This is a full kit that for the MTM Spring Reverb main module, except the spring tank or digital brick. The Music Thing Spring Reverb mk2 is a flexible, easy-to-build voltage controlled DIY mono spring reverb module. Traditional guitar reverbs are tuned to the sound of the guitar and the amplifier it is played through. This circuit is different; designed to be relatively clean and hi-fi, with a lot of bass response. Use real spring reverb tanks, or solid state reverb bricks.New Features of the Spring Reverb mk2 include:• Internal Feedback control with CV input, dedicated attenuverter and with invert switch for maximum feedbackiness• Wet out and feedback in sockets for more flexible patching• 3HP Expander – allows for instant switching between reverb brick and spring tank – or set a blend between the two• Expander also allows for front panel send and return to spring tank.• New improved circuitMore Features:• Works with a variety of spring reverb tanks (optional), or with the Accutronics BTDR-2 reverb ‘brick’ designed by Brian Neunaber (optional)• Vactrol (VTL5C3) crossfade between dry and wet (vactrol circuits are variable in their ability to go completely 100% wet, like the Make Noise Echophon for example)• Tilt EQ on the reverb send to tune the voice of the reverb• X-Fade input so the module can also be used as a standalone vactrol crossfader (crossfade demo)• Feedback circuit with positive and negative phase• Attenuverter on the crossfade CV input• 6HP wide (NB: If using the brick, mounted horizontally, the brick extends 5mm over the PCB to the left of the module, around 25mm back from the front panel, so mount the reverb next to a shallow module)• Expander with Front panel mount Phono sockets & Crossfade between reverb types.Instead of the reverb tanks you can use a digital brick, which you can find at Banzai Music http://www.banzaimusic.com/Belton-ReverbsFeatures:We provide genuine Accutronics/Belton Spring Reverb Tanks separately, have a look in our shop. They produce high quality and springy responses!Medium – 8EB2C1B Springs: 3, Delay Type: Medium, Tank Dimensions: 23.5 x 8.5 x 3.3cm, Input Impedance: 800 Ohms, Output Impedance: 2575 Ohms, Mounting: Horizontal Open Side Down, Connectors: Input Insulated – Output GroundedLarge – 9EB2C1B Springs: 3, Delay Type: Medium, Tank Dimensions: 42.5 x 12 x 3.3cm, Input Impedance: 800 Ohms, Output Impedance: 2575 Ohms, Mounting: Horizontal Open Side Down,DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
The passive Spring Expander adds phono sockets on a separate front panel plus adds a blend knob for brick/tank.• This is a very simple passive expander for the revised Spring module, which brings the phono connections to the front panel — ideal for smaller cases — and adds a simple mix control to blend real spring tanks with the solid state reverb 'brick'.• The main reverb module has phono sockets on the back, so you can put a reverb tank inside your modular case. Often, you might want to mount the spring tank outside the case; for small cases, or for access to the springs — stroking them or muting them or ‘preparing’ them in some way. This little 3hp expander makes that simple.• The panel is designed to be reversible, depending how you want to arrange the cable to your spring tank.• The expander also has a simple mix pot to blend the spring and brick reverbs together — this is a really nice effect, particularly when using feedback.• Weird patch trick: If you use the expander with a brick, but without a spring connected to the front or back of the module, the spring drive circuit will overdrive massively (the spring pickup is part of the feedback loop of an op amp, so without it you get open loop gain). Fading across to spring and playing with feedback and EQ can get some really crunchy, squeaky extreme distortion that can be quite controllable with the blend control.• If you want to know more about spring reverb than you ever thought possible, enjoy my Medium post Everything I know about spring reverb.• This is a very simple build - just a potentiometer and a couple of wires soldered onto the PCB, but if you have any trouble the best place to find help is in the Spring Reverb Github Issues List. Remember to search for closed issues as well as open ones.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The Twin Drive is a 4 HP Drive/Distortion module inspired by the classic Minimoog input gain. Twin Drive is a stereo version of the Mini Drive, with left and right inputs – the left input is normalled to both outputs so the module can be used with mono signals as well. The Drive knob goes from zero/silent to lots of gain. It’s a dirty gain for modular level and works well with line level inputs – like a drum machine. It’s not suited as an external input for guitar.Using this module is a great way to make a polite sound source into something less polite, but always experiment with the levels! – the output can sound completely different depending on the settings and it can also be used to just add a nice bit of warmth to your input.While it doesn’t have CV in you can either put a VCA or a filter before to modify the amount of grime, or get more experimental and try blasting an LFO or a sequence into one input to see what it does to audio in the other input.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Elmyra 2 is a 4-voice digital/analog hybrid platform for microtonal sonic exploration, capable of creating anything from lush ambient soundscapes to gritty droning textures and shrieking noises, available as a 42 HP Eurorack module or semi-modular desktop synth. With 31 modulation targets, 4 polymetric sequencers, delay, additional per-voice effects, a choice of various filters, as well as onboard LFOs and utilities, it is essentially a purpose-built small modular system in itself. A set of preset cards (included) or electronic components like capacitors or diodes can be plugged into the front panel in order to change the sound character.Features:• 4 independent voices activated by touch or CV• wavetable-based complex oscillator engine, up to 12 oscillators in total, 1V/octave compatible• chromatic mode makes chords and harmonic sounds possible, microtonal scales supported• 41 patch points• 31 modulation targets• touchpads with analog envelopes that can be used as modulation sources• resonant filter switchable between:• boomy and aggressive multimode 2-pole state variable filter (low-pass, band-pass, high-pass)• creamy 4-pole low-pass ladder filter• delay with unhealthy amounts of feedback• lo-fi reverb• analog OUCH circuit: a unique combination of destructive distortion, waveshaping and filtering• sonic character can be customised by using special preset cards (set of 4 included) or components like diodes that can be plugged into the front panel• preset cards can be used with other Neutral Labs modules• external audio can be processed via audio input• 9 per-voice modulations and effects:• unison detune• dual sub-oscillators• saturation• bitmangler• sample rate reduction• noise• high-pass filter• low-pass filter• 2 LFOs: 1 sine, 1 complex morphable• 4 sequencers with arbitrary step length per voice (up to 128), allows polymetric structures• delay time and LFOs can be clock-synced or unsynced (tap tempo is also possible)• utilities• dual attenuator/buffered multiple/voltage generator• CV summing circuit• solid bamboo wood case• boutique synth handmade in GermanyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Elmyra 2 is a 4-voice digital/analog hybrid platform for microtonal sonic exploration, capable of creating anything from lush ambient soundscapes to gritty droning textures and shrieking noises, available as a 42 HP Eurorack module or semi-modular desktop synth. With 31 modulation targets, 4 polymetric sequencers, delay, additional per-voice effects, a choice of various filters, as well as onboard LFOs and utilities, it is essentially a purpose-built small modular system in itself. A set of preset cards (included) or electronic components like capacitors or diodes can be plugged into the front panel in order to change the sound character.Features:• 4 independent voices activated by touch or CV• wavetable-based complex oscillator engine, up to 12 oscillators in total, 1V/octave compatible• chromatic mode makes chords and harmonic sounds possible, microtonal scales supported• 41 patch points• 31 modulation targets• touchpads with analog envelopes that can be used as modulation sources• resonant filter switchable between:• boomy and aggressive multimode 2-pole state variable filter (low-pass, band-pass, high-pass)• creamy 4-pole low-pass ladder filter• delay with unhealthy amounts of feedback• lo-fi reverb• analog OUCH circuit: a unique combination of destructive distortion, waveshaping and filtering• sonic character can be customised by using special preset cards (set of 4 included) or components like diodes that can be plugged into the front panel• preset cards can be used with other Neutral Labs modules• external audio can be processed via audio input• 9 per-voice modulations and effects:• unison detune• dual sub-oscillators• saturation• bitmangler• sample rate reduction• noise• high-pass filter• low-pass filter• 2 LFOs: 1 sine, 1 complex morphable• 4 sequencers with arbitrary step length per voice (up to 128), allows polymetric structures• delay time and LFOs can be clock-synced or unsynced (tap tempo is also possible)• utilities• dual attenuator/buffered multiple/voltage generator• CV summing circuit• case made of plant-based bioplastic and native German oakwood• boutique synth handmade in GermanyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
This is the DIY Desktop version of this unit.Logic, Unbound. Meet Luna. The first serious Lunetta synthesizer.Look beyond clean waveforms and predictable polyphony. Luna takes you back to a time when digital didn’t mean perfect. It meant raw. Inspired by the subterranean DIY culture of the 70s and 80s, Luna is a love letter to the Lunetta machines of old – living, breathing organisms built from CMOS logic chips. But where those machines were fragile experiments, Luna is a weaponised instrument of sonic confusion.The Nervous System Exposed. True to the Neutral Labs philosophy, we don’t believe in hiding the magic behind an opaque faceplate. Luna features exposed CMOS inputs and outputs directly on the front panel. You're not simply patching cables – you are rewiring the brain of the synthesizer itself. Combine signals, bend logic, and physically intervene in the computation to create sounds that shouldn’t exist.Rhythm is Timbre. Timbre is Rhythm. In the world of Luna, there is no difference between a sequencer and an oscillator. The same digital pulse that drives a bass line can be accelerated into a screeching lead or folded into a metallic drone.Five oscillators provide the raw material. A chaotic array of logic blocks (XOR, NOT, AND, shift registers, counters, multiplexer) chews up those signals and spits out complex, evolving mathematical noise.Taming the Digital Mess. Raw logic can be harsh. To turn this binary chaos into music, Luna feeds its digital soul through three organic low-pass gates. These analogue circuits impart a natural decay and percussive punch to the madness, transforming mathematical errors into bongos, plucks, and thumping basslines.Drench it in Atmosphere. Once you’ve constructed your signal, destroy it again. Luna comes equipped with a suite of effects – distortion, delay, reverb, chorus, bitcrusher, phaser and more – to smear your logic into a wash of ambient bliss or gritty industrial texture.Features:• 5 oscillators• Logic gates (2 XOR, 2 NOT, 2 AND)• 5 logic blocks (5-step ring counter, 4-bit binary counter, 2 shift registers, 4-channel multiplexer)• 3 touchpads that generate logic signals• 3 channels for audio manipulation (low-pass gates with adjustable decay and switchable trigger mode, gain, tilt EQ)• 13 audio effects freely assignable to 2 effect slots running in series (drive, delay, reverb, 6 filter types, bitcrusher, phaser, chorus, comb filter)• CV control for effects and 2 oscillators• MIDI control over 2 oscillators, all 3 low-pass gates, and 3 logic outputs• 2 sequencers with up to 64 steps, syncable to clock or MIDI• Headphone-compatible audio outputDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
This is the DIY Eurorack version of this unit.Logic, Unbound. Meet Luna. The first serious Lunetta synthesizer.Look beyond clean waveforms and predictable polyphony. Luna takes you back to a time when digital didn’t mean perfect. It meant raw. Inspired by the subterranean DIY culture of the 70s and 80s, Luna is a love letter to the Lunetta machines of old – living, breathing organisms built from CMOS logic chips. But where those machines were fragile experiments, Luna is a weaponised instrument of sonic confusion.The Nervous System Exposed. True to the Neutral Labs philosophy, we don’t believe in hiding the magic behind an opaque faceplate. Luna features exposed CMOS inputs and outputs directly on the front panel. You're not simply patching cables – you are rewiring the brain of the synthesizer itself. Combine signals, bend logic, and physically intervene in the computation to create sounds that shouldn’t exist.Rhythm is Timbre. Timbre is Rhythm. In the world of Luna, there is no difference between a sequencer and an oscillator. The same digital pulse that drives a bass line can be accelerated into a screeching lead or folded into a metallic drone.Five oscillators provide the raw material. A chaotic array of logic blocks (XOR, NOT, AND, shift registers, counters, multiplexer) chews up those signals and spits out complex, evolving mathematical noise.Taming the Digital Mess. Raw logic can be harsh. To turn this binary chaos into music, Luna feeds its digital soul through three organic low-pass gates. These analogue circuits impart a natural decay and percussive punch to the madness, transforming mathematical errors into bongos, plucks, and thumping basslines.Drench it in Atmosphere. Once you’ve constructed your signal, destroy it again. Luna comes equipped with a suite of effects – distortion, delay, reverb, chorus, bitcrusher, phaser and more – to smear your logic into a wash of ambient bliss or gritty industrial texture.Features:• 5 oscillators• Logic gates (2 XOR, 2 NOT, 2 AND)• 5 logic blocks (5-step ring counter, 4-bit binary counter, 2 shift registers, 4-channel multiplexer)• 3 touchpads that generate logic signals• 3 channels for audio manipulation (low-pass gates with adjustable decay and switchable trigger mode, gain, tilt EQ)• 13 audio effects freely assignable to 2 effect slots running in series (drive, delay, reverb, 6 filter types, bitcrusher, phaser, chorus, comb filter)• CV control for effects and 2 oscillators• MIDI control over 2 oscillators, all 3 low-pass gates, and 3 logic outputs• 2 sequencers with up to 64 steps, syncable to clock or MIDI• Headphone-compatible audio outputDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Meg is a unique kind of waveshaper. Instead of folding the wave back in on itself like a common wavefolder, it shifts parts of the wave up or down, with the shifting threshold being adjustable. The resulting 2 half-waves can be flattened one by one, essentially morphing into a half square wave and eventually a full square wave. Essentially, it will add pulse-width modulation (and more) to any kind of wave. Both knobs can be fully CV controlled.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Nermal is discontinued for now - sorry. Nermal is a destructive distortion Eurorack module that has some unique sonic qualities. There are 3 levels of distortion ranging from subtle saturation to utter destruction. An integrated modulator can switch or even blend between these modes, with the modulation frequency going well into the audio range, in which case, interesting harmonics and artefacts can be created on top of the incoming audio. Nermal rewards experimentation and unexpected sweetspots can often be discovered along the way. In addition to the onboard modulator, there are external modulation options via control voltages (CV) for the most commonly used parameters. LFOs and envelopes work great, but audio signals are accepted as well and make for the most interesting patches.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
A 4 HP distortion module that allows the flavour of the sound to be changed by separately available preset cards, or even just individual components that can be plugged directly onto the front panel, like diodes, capacitors and resistors. Maybe you would want to try an LED combined with a photoresistor? The cards (Product name: Nuts) are also compatible with the Scrat VCF module.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Nuts is a set of four preset cartridges for Neutral Labs Scrat and Nijel. They give you instant access to a variety of filter sounds. Please read the Scrat manual to get a detailed explanation about how it works. Elmyra 2 has different preset cards, but they should also work with Scrat and Nijel.
sold out at the moment
The Coiler Multi-mode Filter and Rectifier packs an entire nest of sound-shaping features into a single 8HP Eurorack module. It's a two-pole state-variable filter based on a unique integrator design which stores energy in both inductors and capacitors depending on the frequency range. The transition region between the two components, and the saturation characteristics of the traditional OTA-based amplifiers, offer warmth and ever-shifting timbres in the midrange, along with hissing highs and slithering lows. This is a somewhat unpredictable filter.With simultaneous low-pass, band-pass, and high-pass outputs, the Coiler works well in traditional subtractive patches. But its built-in full-wave rectifier is also great for adding harmonics and distortion in patches from the other coast. When combined with low-pass, the rectifier allows the Coiler to serve as a basic envelope follower, for compression and external-signal patches. It's a lot of bite for the buck, and for the rack space.The MSK 009 Coiler VCF is available as a pre-built 6HP Eurorack module or a DIY kit. Slide one into your rack today.Features:• High-quality potentiometers with bushings fastened to the panel for wobble-free operation; conductive plastic for smooth feel; rated for one million operations lifespan (compare to fifteen thousand or less for typical cheap pots)• All-new circuit, not a clone or imitation of anything else• Through-hole for easy hand construction and maintenance• No compromises on build quality: real aluminum panel, not PCB material, with colour printing; nickel and gold plating on the circuit board; close-tolerance metal film fixed resistors.• Fully open design - no lock-inDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
North Coast makes the Eurorack four-knob utility mixer sound great again with this minimalist design featuring just six transistors. Where a conventional mixer would typically require at least five operational amplifier units each containing a dozen or more transistors, we cut the complexity and distill mixing to its essence. This is a new design made with current components and modern manufacturing quality; but its Class A amplifiers operate on principles that go all the way to the dawn of electronic signal processing.Suitable for both audio and control voltages, with bonus features that don't compromise the minimalist philosophy: positive and negative offset; simultaneous DC- and AC-coupled outputs; maximum gain a little over unity for when you need that extra push over the cliff. It can also function as a transistor distortion effect, by offsetting the signal until it clips and then using the AC-coupled output.Features:• High-quality potentiometers with bushings fastened to the panel for wobble-free operation; conductive plastic for smooth feel• All-new design, not a clone or imitation of anything else• Classic discrete-transistor design style; DIY kit ships with silicon 2N5088 transistors for a clean modern sound, easily modifiable to use other recent or "vintage" types• No ICs!• Through-hole for easy hand construction and maintenance• No compromises on build quality: real aluminum panel, not PCB material, with colour printing; nickel and gold plating on the circuit board; film output coupling capacitor; close-tolerance metal film fixed resistors.• Fully open design - no lock-inDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
North Coast's complex VCO is comfortable on a journey to the East or the West, while providing a stable foundation at home in any Eurorack. The module contains two triangle-core VCOs, each with four waveforms and standard V/octave control. As basic VCOs running independently these can be the heart of a traditional subtractive East Coast synthesizer. But the Middle Path's oscillators can also be used together, with or without sync, to drive its unique multi-output Gilbert-style sine shaper. The shaper, which can also take external input, offers wave shaping, distortion, folding, phase modulation including through-zero, and imitation stereo. These effects take the sound into West Coast territory.The design emphasis is on harmonious combination of simple principles. The exponential converter uses premium analog multipliers and a transistor array to ensure temperature stability without fiddly adjustments or hard-to-control "tempco" resistors; it should provide consistent tracking, and especially between the two oscillators, without needing to warm up. The triangle cores are intrinsically frequency-accurate without needing extra circuitry to compensate for reset time. The sine shaper includes our own novel quadrature modification which can be used to generate a stereo signal or in combination with other modules to create frequency shift effects. The sync circuit joins the oscillator cores in another way with a selection of soft and firm modes.Features:• High-quality potentiometers with bushings fastened to the panel for wobble-free operation; conductive plastic for smooth feel• Normalization to the Eurorack bus allowing it to receive pitch control without needing an input patch• All-new design, not a clone or imitation of anything else. Innovative quadrature sine shaper offering through-zero phase modulation with a range of up to 1080°• Genuine AD633 and THAT320 chips in the exponential converter; sockets on all DIP ICs• Through-hole for easy hand construction and maintenance• Connectors between boards, and panel controls mounted on a board - no flying wires• No compromises on build quality: real aluminum panel, not PCB material, with colour printing; panel screwed solidly to both the PCBs and the pots and jacks, for maximum ruggedness; nickel and gold plating on the circuit boards; close-tolerance metal film fixed resistors.• Fully open design - no lock-in.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.