Effects
available
Chopping kinky is a voltage controllable, dual channel wavefolder.As an unique feature it has a chop out that will choose between both channels with a zero cross detector or an external gate.• A wavefolder converts simple signals into richer and more dynamically changing ones. In contrast to a filter, wave folding adds harmonic content to the waveform. It works by amplifying the waveform until it begins to saturate, then rather than clipping, the waveform gets folded back in on itself.• Each of the module’s two channels has a unique wave folding profile. At each input, there are two CV inputs for controlling the level of waveshaping including one that passes through an attenueverter.• Chopping Kinky is DC coupled allowing it to be used for both CV and audio duties; to generate harmonics on an audio signal or kinking LFOs and envelopes.Features:• Two unique wavefolder circuits• Two CV inputs per channel, one with attenuverter.• DC Coupled inputs allowing CV signals.• Chop out with zero cross detector.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Crush Delay v3 is a special Echo-Delay unit based on the PT2399 IC, which is able to offer 400ms of clean delay and up to 2 seconds of dirty repetitions, having a special talent to generate noisy-glitch textures. This third version comes with some interesting new features like redesigned VCAs circuits, wider range for clean delay and reduced depth to make it skiff friendly.• The module has two inputs (In and Return) that go to the Delay circuit through a dedicated VCA for each one. The main difference between both inputs is the signal fed into In is going to the Dry/Wet circuit also, not only to the Delay, allowing you to control the balance between the original and the processed signal present at the main output (Out).• The signal is processed by the Delay circuit, which is affected by the Crush section. It degrades the signal at slow rates in different ways, depending on the position of the three Crush switches or by the presence of gate signals at the Crush inputs.• After being processed, the signal is routed to three different paths. The first one goes into Dry/Wet, where it’s mixed with the original input signal (In) before going to the main output (Out). The second one is returned to the Delay circuit through another VCA (Feedback), controlling the number of repetitions of the wet signal. Finally, the last one goes directly to the Send output.Features:• Input signal controlled by VCA’s• Bigger range of clean delay• Three different Crush Modifiers based on circuit bending techniques.• VC Feedback wit automatic gain controlDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
A Multi FX module based on game carts!Fx Boy is a multi-FX module designed in collaboration with several talented manufacturers. This is an effect unit with CV control over the parameters and dry/wet control, with a Built-in CV controllable four bands EQ.Each effect is physically hosted in a hot-swappable game cart and designed by a different manufacturer: Touell Skouarn with Skuara a harsh fuzz with overdrive, Instruo with micro Phaser, a two-flavoured Phaser, Feedback modules with a vintage Flanger, XOR with FX-Girl, a digital double effect module: Delay + Granularizer, Making sound machines with an analog Wave folder, Tesseract with a bit crusher and Befaco Trash distortion!Please note that the cards add current consumption on top of the values stated here.Features:• CV control over all parameters and dry/wet• CV controllable four-band EQ, routable post or pre-effect.• Selector for two different flavours of each cart.• Open specifications to design your own carts• Hot swap for all carts. (A tiny pop can occur depending on the cartridge design)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
IROI is a compact 18HP stereo effects processor designed to transform external sound sources into deep, atmospheric textures. Based on the processing concept of Oneiroi, it offers a focused signal chain with a new mapping structure, making it easy to shape evolving drones, cinematic layers, harmonic movement and character-filled soundscapes from any incoming audio.At its core, IROI combines a stereo multimode filter, fast digital VCA, 3-band resonator, 2-tap echo and experimental reverb. The filter/VCA block can be placed at different points in the signal chain, allowing flexible tone shaping before or after other processing stages. The multimode filter offers low-pass, high-pass, band-pass and comb modes, ranging from smooth spectral control to metallic, animated coloration.The resonator adds physical presence and harmonic depth, while the echo and reverb sections create anything from lo-fi repeats to wide, immersive spaces. The Spacetime control moves smoothly between short, long and inverted reverb behavior, opening up dense, blooming atmospheres with a strong sonic identity.IROI also features a powerful modulation and mapping system. Parameters can be randomized, modulated or CV-controlled with adjustable depth, while the internal LFO, envelope follower and seven selectable wave shapes allow sounds to move, react and reshape themselves over time. Global Mod Level control makes it possible to scale all active mappings at once, keeping complex modulation playable and controlled.Features• Compact 18HP stereo effects processor for external sound sources.• Inspired by Oneiroi with a focused signal chain and new mapping structure.• Stereo multimode filter with low-pass, high-pass, band-pass and comb modes.• Fast-response digital VCA for dynamic signal shaping.• Filter/VCA block can be placed at different points in the signal chain.• 3-band resonator for metallic texture and harmonic depth.• 2-tap echo for rhythmic repeats and lo-fi delay character.• Experimental reverb with macro control over size, filtering and direction.• Spacetime control for smooth transitions between short, long and inverted reverbs.• Internal LFO, envelope follower and seven wave shapes for self-modulation.• CV control with attenuators on most parameters.• Powerful randomizer with four target modes plus undo/redo.• External sync input for synchronized modulation and timing.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Lich is a programmable multi-function module based in the Rebel Technology OWL platform that allows you to use Pure Data, Max Gen or Faust code into your module!.Lich is a Befaco Rebel collaboration that brings back Owl’s platform with this new hardware iteration. It has stereo in and out, four pot controls summed to cv inputs (like the classic Owl module) And as addition, CV and Gate outputs, patch selection with display and USB MIDI host and device connections.Features:• Stereo Audio IN and OUT at 48k 24 bits.• 4 CV controls (Pot + Attenuated CV in)• 2 CV outputs.• 2 Gate intputs + buttons.• 1 Gate Output.• Patch selection and visialization via display.• USB host and Device connectionsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Experimental synth voice focused on ambient pads and drone-like soundscapes.Features:• Stereo External input with selectable gain.• 5-second looper Records either the stereo input or the module’s output• Sine oscillator• Supersaw oscillator• Wavetable oscillator that uses the Looper buffer• Multimode filter: low-pass, band-pass, high-pass, and comb filter.• 3-band resonator• 2-tap echo• Reverb with macro control for size, filtering, and direction.• CV Control with attenuators on most parameters.• Various types of self-modulation with configurable routing and control over level and speed.• External synchronization via sync input.• Powerful randomizer with four different targets, three levels of intensity and undo/redo.• Knobs catch behavior functionality for re-coupling parameters’ positions.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Oneiroi is a full-stereo synthesizer crafted for dreamlike soundscapes, immersive textures, and cinematic atmospheres. At its core lies a rich combination of synthesis engines and creative sound processing: a sine wave oscillator, a versatile wavetable/supersaw voice, and a playful looper capable of recording external input or internal output with “sound-on-sound” layering. These elements flow into a powerful effects section featuring a multimode filter, resonator, stereo delay, and lush reverb—ideal for generating hypnotic drones, evolving pads, and experimental sonic landscapes.Modulation possibilities within Oneiroi are highly flexible, thanks to complex internal routing and a powerful randomizer that generates instant patches at the press of a button. With four distinct targets, three levels of intensity, and dual switch-controlled behavior, it lets you dial in anything from subtle variation to wild, unpredictable textures—complete with undo/redo to capture the perfect moment.The built-in 5-second looper not only captures audio but also feeds directly into the wavetable oscillator, enriching your sound palette with evolving textures. Whether you're layering field recordings, sampling your own tones, or sculpting ambient washes from scratch, Oneiroi encourages spontaneous creativity and deep modulation.This version includes a 4ms Pod 42 HP powered case, transforming Oneiroi into a self-contained, portable stereo powerhouse—perfect for live performance, studio exploration, and ambient sessions on the go.Features:• Stereo External input with selectable gain.• 5-second looper Records either the stereo input or the module’s output• Sine oscillator• Supersaw oscillator• Wavetable oscillator that uses the Looper buffer• Multimode filter: low-pass, band-pass, high-pass, and comb filter.• 3-band resonator• 2-tap echo• Reverb with macro control for size, filtering, and direction.• CV Control with attenuators on most parameters.• Various types of self-modulation with configurable routing and control over level and speed.• External synchronization via sync input.• Powerful randomizer with four different targets, three levels of intensity and undo/redo.• Knobs catch behavior functionality for re-coupling parameters’ positions.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Analog Thru-Zero Wavefolding VCO/LFOPony VCO is a fully analog Thru-Zero oscillator with wavefolder and dedicated VCA in only 4HP. The module offers great stability and tuning capabilities thanks to its powerful core, based on Sound Semiconductors IC. It comes with range selector, that allows it to go down to LFO range, as well as octave and waveform selectors.In Through Zero oscillators, frequency is controlled by either positive and negative voltage. If FM CV goes below zero, the core will continue oscillating inverting its phase. This “little” change of behaviour allows the core to create a whole new range of timbres that are just impossible to achieve with regular VCOs. If you set the module as LFO, the range of funky modulations will be endless!There is a separate panel for conversion to 1U available. You can use the 1U panel with the normal 3U module, but have to buy it additionally and you have to make some changes by soldering a hand full of SMD parts, but it's quite easy. 1U format keeping the same functionality and control layout.In Through Zero oscillators, frequency is controlled by either positive and negative voltage. If FM CV goes below zero, the core will continue oscillating inverting its phase. This “little” change of behaviour allows the core to create a whole new range of timbres that are just impossible to achieve with regular VCOs.If you set the module as LFO, the range of funky modulations will be endless!Features:• Through Zero Frequency Modulation• Wavefolding (Timbre)• Pulsewidth Modulation (PWM)• SYNC• VCA• LFODIY-Kit-Type:Semi-DIY-Kit. Most of the components are completely ready, you only have to assemble panel, knobs and some screws/washers.
only 2 left
This is our take on an analog spring reverb module. Featuring VCAs for the two available inputs (with different routing), CV control for DRY/WET and visual feedback for signal levels at input and output of the tank.Reverberation can be defined as the sum of all the reflections created from an initial sound source within a space, at a point within that space, over time.To simulate this effect we can pass a sound through a spring with two transducers at either end. As the sound propagates it will cause the spring to expand and contract, creating a series of reflections that are picked up by the transducers (along with the original sound). This creates a simulation of reverberation with (in the case of spring of the reverb) a characteristic and classic colour.Electronically generated audio will usually sound starkly different to acoustically generated sound. This is more-often-than-not a desirable thing, but there are times when you might want to bring the “depth” of an acoustic environment back into your mix.The obvious difference between acoustic and synthesised sounds is that acoustic instruments have resonators, and exist in reverberant spaces. One way to add depth to an electronic sound is to somehow simulate the characteristics of a space, and mix this with the original signal.Features:• Two CV controlled audio inputs. In 1 (routed to Dry) and In 2 (routed directly to the tank)• Two independent Mix and Wet output.• High-pass filter on tank’s input to control the colour of the reverberation.• Vu-Meter to visualize level on Wet output.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
This is our new collaboration with Robin Vincent aka Molten Music Technology. A Stereo bypass module to gate control the send of your signals to your favorite effect!Molten bypass features a hard/soft bypass control, to hard cut the return of your effect or allow the long tails of your reverb to stay after you bypass the effect. Also a gate/latch control to use either triggers or gates for control and a gain control for the returned signal.Features:• Full stereo signal path• DC coupled• Hard or soft bypass selection• Gate or Latch possibility• Manual or Gate control• Gain control over the returnDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Cosmos is a new kind of module that will help you to creating complex modulation, sounds, patterns with ease and will lead you to new sounds territories.Inspired by early analog computers, Cosmos is a unique, innovative, very flexible and fully analog module allowing it to be used as: VCO, LFO, Ring Mod, Polarizer, “VCA”, “LPG”, Phase Lock Loop, Cross-Modulation, Minimum, Maximum, Logic Gates, Waveshaper, Complex gate generator, Fuzz, Distorsion, Gate extractor, Trig extractor, Gate generator, Voltage generator, Trig Generator, comparator, window comparator, complex comparator, Half-Rectifier, Full-Rectifier, Inverter, Buffered Multiples, Mixer, Difference, Compressor, Sidechain, compressor, VC Clipper, VC Switch, Clock doubler, Envelope follower, and more.With its wide fields of application Cosmos can replace many modules but it will also bring new colors to your palette thanks to its unique character. This makes Cosmos the ideal module whether you have a small case or a big system. 100% analog and with an intuitive interface Cosmos is also very easy to use, no menu and button combo problems.Inspired by the past and crafted for the future, 100% analog Cosmos was not only thought to be the center of any system but also to blend perfectly with the rest of your case to form a consistent and coherent system.Cosmos was designed not only to be a swiss army knife module but also to push you to explore and you help create new sounds and explore sonic territories that were previously unattainable.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Dual Rectifier II is a small yet versatile and essential module for any Eurorack system. It can be used as an AC to DC converter, a distorsion, a complex waveform generator, a frequency doubler, a clock doubler or an envelope follower and more.Like all our modules, Dual Rectifier II is built with high-quality components only and designed to offer the best performance.Whether you're starting a small system or have a wall full of modules, Dual Rectifier II is a must-have for any Eurorack system.DUAL RECTIFIER II is divided into two sections:On top section the Positive Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 1.-Output 2 Half-rectified, signal from input 1 below 0V will be remove.-Output 3 Full-rectified, signal from input 1 below 0V will be rectified.On bottom section the Negative Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 2.-Output 2 Half-rectified, signal from input 2 above 0V will be remove.-Output 3 Full-rectified, signal from input 2 above 0V will be rectified.By default input 2 is normaled to output 1 (inverted) of the top section.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Dual Rectifier II - S is a small yet versatile and essential module for any Eurorack system. It can be used as an AC to DC converter, a distorsion, a complex waveform generator, a frequency doubler, a clock doubler or an envelope follower and more.Like all our modules, Dual Rectifier II is built with high-quality components only and designed to offer the best performance.Whether you're starting a small system or have a wall full of modules, Dual Rectifier II - S is a must-have for any Eurorack system.DUAL RECTIFIER II - S is divided into two sections:On top section the Positive Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 1.-Output 2 Half-rectified, signal from input 1 below 0V will be remove.-Output 3 Full-rectified, signal from input 1 below 0V will be rectified.On bottom section the Negative Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 2.-Output 2 Half-rectified, signal from input 2 above 0V will be remove.-Output 3 Full-rectified, signal from input 2 above 0V will be rectified.By default input 2 is normaled to output 1 (inverted) of the top section.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The GOMA Pro pushes the boundaries of the attenuverter-mixer concept.Attenuator, attenuverter, offset generator, voltage generator, waveshaper, distorsion, GOMA Pro can do all of that and more. Engineered for precision, GOMA Pro is crafted using high-quality components to ensure maximum accuracy, including low-tolerance resistors and low-noise op-amps.GOMA Pro offers 3 channels fully analog to amplify (up to x10 gain!), attenuate or polarize (attenuverter) any signal, from CV, audio to line level sources.Additionally, each channel can act as a high precision voltage generator (–10V to +10V) to offset another channel or control external parameters.The 3 channels can be processed separately or summed through cascade mixing, which can extend further than a single module since all the GOMA family (I, II, Pro) can be daisy chained to unlock virtually infinite mixing.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Voltage Processor is designed to pack a lot of features in a small module.Here a some of the features you can achieve with Voltage Processor. You can find how to setup those features in the manual below.Features:• Dual VCA• Stereo VCA• CV Crossfader 2:1• CV Crossfader 1:2• Dual AM• CV PAN• Dual Attenuator• Dual Inverter• Dual Offset generator• Dual Voltage generator• Dual Exponential converter• Logarithmic converter• Dual PWM• Dual CV overdrive• Dual waveshaper• Complex waveshaper• Dual RingMod• RindMod• Compressor• Sidechain compressorDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The Arkarion is a full-featured analog synthesizer voice in Eurorack format, designed for creative exploration and dynamic signal flow. Combining the warmth of analog circuitry with a digitally controlled internal routing system, Arkarion offers a unique blend of structure and unpredictability. It's an expressive, performance-ready instrument for musicians seeking deep modulation, generative possibilities, and hands-on control.At the core of Arkarion lies a digitally interpreted “DNA patch system” — a signal-routing framework inspired by genetic code. This system unlocks over 65,000 modulation and audio paths, allowing for rich, morphing textures that evolve at the press of a button or incoming gate.Features:• Complete analog synthesizer voice with digital routing control• 2 analog VCOs with selectable waveforms• MIDI input with pitch CV and gate outputs• Envelope generator with rise/fall stages, loop and gated loop modes• 2 CV-controllable LFOs for versatile modulation• Gate-triggered random voltage source• Multimode filter: lowpass, bandpass, highpass, allpass (switchable)• Tape-style analog delay with CV control• Digitally controlled “Gene Modification” knob for live routing mutation• 16-bit routing architecture: 65,536 possible patch configurations• 64 patch memory slots (8 banks of 8 presets)• Internal VCAs for modulation depth control• Randomize routing via button or external gate input• LED indicators visualize current patch structure and modulation pathsDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Gloop is a Eurorack performance looper designed for layered loop manipulation, granular-style textures and hands-on live control. It records audio into a continuous buffer of up to two minutes and plays it back using four simultaneous playheads, each with independent speed, pitch, direction, volume and loop position.Each playhead can scan a different part of the recorded loop or focus on its own sub-loop, making it easy to create dense textures, shifting drones, rhythmic variations and evolving sound beds from a single recording. Four assignable CV inputs allow external modulation of playhead speed, position or volume, and the built-in delay, reverb and bitcrush effects add further sound-shaping options.The two mono outputs allow each playhead to be routed individually or sent to both outputs, supporting flexible effects routing and stereo movement when used with a panning mixer. Grid mode slices the loop into 4, 8 or 16 quantized regions, keeping playback positions and loop sizes locked to rhythmic divisions for precise beat-based performance.Designed for live use, Gloop includes dedicated physical volume controls for each playhead, plus record and overdub control via the front-panel button or trigger input. Compact, immediate and highly flexible, Gloop turns recorded audio into a playable modular instrument for loop mangling, texture building and experimental sampling.• Eurorack performance looper with four simultaneous playheads.• Up to two minutes of continuous 48kHz / 24-bit audio recording.• Independent speed, pitch, direction, volume and position per playhead.• Sub-loop control for layered textures and granular-style playback.• Four assignable CV inputs for speed, position or volume modulation.• Built-in delay, reverb and bitcrush effects.• Two mono outputs with flexible playhead routing.• Grid mode with 4, 8 or 16 quantized loop regions.• Record and overdub via button or trigger input.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only -1 left
The Dannysound Dynamics is a compressor / expander originally designed to process drums but like most processing devices, it can be used for a wide variety of applications.The module comprises of:• Compressor / Expander• Sub Bass Enhancer• 3 Band Inductor-based EQ• Harmonic ExciterThe compressor / expander section uses a discrete transistor-based circuit that allows for soft clipping when overdriven.The envelope detector is known as a feedforward type of circuit; taking it’s input from the signal before it goes to the compressor rather than after.This type of circuit is known for having fast attack times.The Sub Bass enhancer has its own compression circuit that “ducks” the initial transient. This allows the sub bass to be increased without distortionon the transient peaks increasing the overall level.There is a MIX control to allow the unprocessed signal to be mixed back in with the processed signal.The 3 band EQ is an inductor based LCR design. After trying out various EQ topologies this was the design that sounded the nicest.When overdriven it gives a nice “bite” to the sound and it has a certain characterful charm that’s hard to put into words.The controls have a response that are subtle to begin with and get more pronounced as the controls are increased.The Harmonic Exciter adds a little distortion to the high frequencies which bring out the sparkle of cymbals or the snap snare drums.The operating bandwidth can be switched between Low (snare drum snap) or High (Cymbals sparkle).There are inputs for side chaining and control with an external envelope as well as an envelope out to make the envelope detector output available to drive other modules.It also features separate inputs and outputs for the Compressor / Expander and EQ sections, so they could be used as 2 separate modules.Features:• Compressor / Expander• Sub Bass Enhancer• 3 Band Inductor-based EQ• Harmonic Exciter• Envelope In/Out• Sidechain Input• Separate In/Out for Comp/Exp and EQ sectionsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The Timbre is a 6HP Eurorack module based on the wave folder section of the Buchla 259 oscillator as implemented in the Music Easel.The wave folder adds extra harmonics to input signals that have low harmonic content to creating rich and interesting timbres.Typical input sources to use would be Sine and Triangle waves but you are welcome to try other sources as well!The Dannysound Timbre adds an extra input to the Buchla design to allow 2 oscillators to drive the wave-folder simultaneously –this dramatically increases the range of possible tones that can be generated and allows the folder to go wild!Buchla 259 inspired waveshaper, the perfect module to put in-between your Dannysound Cali and EN129 oscillators!Features:• Osc1 / Osc2 Mix – Adjusts mix between oscillator 1 and 2 inputs, also acts as an attenuator if only one of the inputs is used.• Timbre Control – Adjusts the overall wave fold amount.• Timbre CV – Bipolar (attenuverter) controls the Timbre CV input.• Symmetry – Adds an offset to the input so the top half of the wave starts folding earlier.• Blend – Mixes between the clean and effected sound.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
This module is based around a BBD integrated circuit and allows for classic delay-based effects, from slapback echoes to trailing reverberations, from flanger-like sounds to crusty down-sampled madness.The module is DIY, sold as a kit by Erica Synths and comes with a very thorough assembly manual that provides deep insight into the functioning of every part of the circuit you'll build.The module itself features all your classic delay-related controls, from delay time to feedback amount, a dry/wet mix control and even a switch to select between 2 different delay ranges.A nice, surprising addition is a patch point labeled "Inhibit CV" which, whenever it is presented with a gate signal, will disconnect the clock signal from the BBD chip, essentially stopping the effect in its tracks. The clock will resume as soon as the gate goes low at this patch point, and the BBD circuit will then return to normal operation. This feature lets the player add some rhythm to the effect or perform other interesting shenanigans.We - Erica Synths and Moritz Klein - have developed a series of educational DIY kits under the brand name mki x es.EDU with one specific goal in mind: to teach people with little-to-no prior experience how to design analog synthesizer circuits from scratch. What you’ll find in the box is not simply meant to be soldered together and then disappear in your rack. Instead, we want to take you through the circuit design process step by step, explaining every choice we’ve made and how it impacts the finished module.NB! All kits in these series are simple and come with extensive user manuals which can be downloaded separately, therefore we will not provide customer support in case your DIY build fails to function or similar.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.