Dannysound - Dynamics
Product information "Dannysound - Dynamics"
The module comprises of:
• Compressor / Expander
• Sub Bass Enhancer
• 3 Band Inductor-based EQ
• Harmonic Exciter
The compressor / expander section uses a discrete transistor-based circuit that allows for soft clipping when overdriven.
The envelope detector is known as a feedforward type of circuit; taking it’s input from the signal before it goes to the compressor rather than after.
This type of circuit is known for having fast attack times.
The Sub Bass enhancer has its own compression circuit that “ducks” the initial transient. This allows the sub bass to be increased without distortion
on the transient peaks increasing the overall level.
There is a MIX control to allow the unprocessed signal to be mixed back in with the processed signal.
The 3 band EQ is an inductor based LCR design. After trying out various EQ topologies this was the design that sounded the nicest.
When overdriven it gives a nice “bite” to the sound and it has a certain characterful charm that’s hard to put into words.
The controls have a response that are subtle to begin with and get more pronounced as the controls are increased.
The Harmonic Exciter adds a little distortion to the high frequencies which bring out the sparkle of cymbals or the snap snare drums.
The operating bandwidth can be switched between Low (snare drum snap) or High (Cymbals sparkle).
There are inputs for side chaining and control with an external envelope as well as an envelope out to make the envelope detector output available to drive other modules.
It also features separate inputs and outputs for the Compressor / Expander and EQ sections, so they could be used as 2 separate modules.
Features:
• Compressor / Expander
• Sub Bass Enhancer
• 3 Band Inductor-based EQ
• Harmonic Exciter
• Envelope In/Out
• Sidechain Input
• Separate In/Out for Comp/Exp and EQ sections
DIY-Kit-Type:
THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
| Current draw +12 V [mA]: | 85 |
|---|---|
| Current draw -12 V [mA]: | 61 |
| DIY Level: | Advanced |
| Depth [mm]: | 50 |
| Width [HP]: | 12 |
| Format: | 3U |
| Panel / Color: | Silver Alu |
Login
Manufacturer / Hersteller:
Thonk Ltd.
Vantage Point
Unit 14, Floor 6
BN1 4GW Brighton
UK
support@thonk.co.uk
EU responsible:
Hi-Lo-Fi Synthesizers - Dannysound
Schnellerstr. 60
12439 Berlin
Germany
dannysound2000@gmail.com
WEEE-Reg.-Nr. DE 65810189
Product Safety Information
Please read this safety guide before installation or use.
Important Notice & Intended Use
• This kit is intended for adult users experienced in electronics and modular synthesis.
• Assembly, including soldering, is required.
• Proper testing and installation are essential to ensure safe and functional operation.
• The completed module is intended for installation in a Eurorack-compatible synthesizer system powered by ±12V and +5V.
• Use outside this scope may result in malfunction, damage, or safety risks.
General Warnings
Electrical Hazards:
• Ensure the power supply matches the module’s specified voltage and current ratings (refer to the product manual). Incorrect voltage can damage the module and pose a safety risk.
• Never connect or disconnect the module while the Eurorack system is powered on.
• Wrong polarity can damage your module or system. Make sure the module is connected with correct polarity.
Heat Generation:
• The module may generate heat during operation. Ensure proper ventilation within your Eurorack case to prevent overheating.
Sharp Edges:
• The module’s faceplate and components may have sharp edges. Handle with care to avoid cuts or scratches.
Small Parts:
• Contains small parts that could cause a choking hazard. Keep away from children and pets.
Compatibility:
• This module is designed specifically for Eurorack-compatible systems. Connecting it to non-compatible systems may result in damage or malfunction.
Assembly Requirements
• Soldering skills are required to complete the module.
• Ensure a clean, well-lit and ventilated workspace free of flammable materials during assembly.
• Use appropriate tools and safety equipment, such as eye protection.
Testing
• Test the module thoroughly for shorts or incorrect assembly before powering it in your Eurorack system. When the unit has malfunctions due to incorrect assembly, the entire Eurorack system might be damaged. It's a good idea to test it in a separate case with only that single module.
• Use a multimeter or other appropriate tools to confirm proper functionality.
Installation and Use
• Mount securely in a Eurorack case using the provided screws.
• Use only the included or manufacturer-recommended power cable.
• Connect only when the power is off.
• Follow the module's user guide for instructions on operation. Do not exceed the input/output limits specified.
Responsibility
Users are solely responsible for proper assembly and testing. Contact manufacturer support for assistance if needed.
Environmental Safety
• Dispose of the module, its components, and packaging in accordance with local electronic waste regulations.
Liability Disclaimer
• The manufacturer or distributor is not responsible for any injury, damage, or malfunction resulting from improper installation, use, or modification of this product.
Contact Information
For further assistance, contact the manufacturer or our shop support team at:
Tech Creation Lab Leipzig UG (haftungsbeschränkt)
Nonnenstrasse 19, 04229 Leipzig, Germany
support@exploding-shed.com