333modules - Atteo
sold out at the moment
Quadruple attenuator with offset.Features:• +/- 10V DC Offset• Cascade inputDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€101.15*
333modules - VCA4Mix
only 1 left
Four channel VCA and mixer based on the classic LM13700 OTA. The perfect tool for your generative patches thanks to its linear response. Up to 5 signals can be mixed with the additional auxiliar input.Features:• Classic LM13700 OTA• Two sections philosophy. One IN signal to two CV VCAs (disconnection)• Mixer 5 signalsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€107.10*
4ms - Listen Up
available
The Listen Up is a small passive expander for the Listen modules that provides stereo 1/4" (6.35mm) jack inputs and outputs. It connects to one or two Listen modules and/or WAV Recorder module with the included 3-pin cables. There are four 1/4" jacks arranged in left/right pairs. The left jack of each pair can be used as a TRS stereo jack if the right jack is unpatched.Features:• Four 1/4” (6.35mm) jacks arranged in two stereo pairs.• Each stereo pair can be connected to the same module or to separate modules.• Each stereo pair (left/right) is bi-directional (input or output).• Left In and Left Out jacks are TRS stereo if corresponding Right jack is not unpatched. • Uses no power.• Connects directly to host module using 3-pin cables.• Two 3-pin cables included.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€53.55*
%
4ms - Meta Module
available
The MetaModule puts real knobs and jacks on virtual software modules. Step back from the computer and make music with hardware, while keeping the flexibility and expandability of software.THIS PRODUCT IS ASSEMBLED AND NO DIY!The MetaModule comes with over 160 built-in modules from 4ms Company, Befaco, HetrickCV, NonlinearCircuits, and Scanner Darkly, plus clones of popular classics such as the Mutable Instruments Eurorack modules, fun physical modeling algorithms, and lots of handy utilities.All of the included modules are also available on the computer using the free program VCV Rack. Whether you make patches on VCV Rack and transfer them to the MetaModule, or if you just create patches directly on the MetaModule, there are plenty of creative modules to inspire new ways to make music.MetaModule PluginsIf the 160+ built-in module aren’t enough, you can load more modules as plugins. Already there are over 200 modules in third-party plugins from Bogaudio, Valley, ChowDSP, NANO Modular, and the list is growing. We have an SDK available to make it easy for VCV Rack plugin developers to convert their plugin to a MetaModule plugin. Our licensing terms are non-restrictive: developers are welcome to distribute their plugin in any way they wish, commercially or not.Mapping Knobs and JacksThe MetaModule has 12 knobs that can be mapped to virtual knobs. Each knob can be mapped to up eight virtual knobs, and each mapping can have a different range and offset. You also can save a group of mappings as a Knob Set and switch between Knob Sets with the encoder. You also can map the 8 inputs and 8 outputs to virtual module jacks. Also, the MetaModule is a USB MIDI host, so you also can map MIDI CC, note, gate, and other parameters to knobs and jacks.ExpandersThere are lots of ways to customize your MetaModule. A Wifi expander allows you to wirelessly transfer patches from your computer. Add eight more knobs with the Knob expander, or buttons with the Button expander. A CV/Audio expander adds more high-resolution inputs and outputs, and the Gate In/Out expander adds not only gate jacks but also TRS MIDI and I2C.Under the HoodThere are six CV/Audio inputs, two gate inputs, and six CV/Audio outputs. The CV/Audio jacks are all 24-bit, 48kHz DC-coupled, -10V to +10V. A USB-C jack accepts MIDI devices and thumb drives. Patches and plugins can be loaded via a USB drive or microSD Card, and internal flash memory lets you save patches you always want to come back to.The processor is more advanced than anything 4ms has used in the past, and is among the most powerful processors found in Eurorack. Startup time and latency are blazingly fast.Features:Patches• Patches are loaded from microSD Card, USB drive, or via the Wifi expander• Patches can be optionally saved onto internal flash memory• Create patches using VCV Rack or directly on MetaModule• Patches can be given a name and descriptionMappings• Map each physical knob to up to 8 virtual knobs• Set range and offset for each mapping, including inverted control• Knob mappings are grouped into Knob Sets, and changing Knob Sets can be done quickly without menu-diving• Map physical jacks to virtual jacks, seamlessly making splits/mults• Add or edit modules, cables, and mappings in real-time while the patch is playing• Create alias names for mappings like "Kick Drum Level"Interface• Simple, intuitive graphical interface lets you zoom in on details, or zoom out to get a big picture• Patch View displays the patch as faceplates and cables, with knobs, buttons, and lights animating in real-time• Knob Set View simplifies the display, showing only the mapped knobs for the current Knob Set• Module View shows just one module and lists the names of each jack, knob, and control legibly• Mapping View lets you adjust details of a knob mapping• Adjust styles and visual preferences to your liking• Save, rename, duplicate, and delete patches• Firmware updater and plugin loader read from microSD Card or USB driveHardware• 12 Knobs• 8 CV/Audio outputs, 24-bit 48kHz, -10V to +10V, DC-coupled• 6 CV/Audio inputs, 24-bit 48kHz, -10V to +10V, DC-coupled• 2 Gate inputs• USB-C jack: MIDI Host or MSC (External drive) Host• microSD Card slot• Internal Flash RAM for additional patch storage• Dual-core 800MHz Cortex-A7 plus Cortex-M4 co-processor• 512MB DDR3 533MHz RAM• Bare-metal operation for fast startup and low latencyDIY-Kit-Type:Assembled unit. This is completely ready to use, nothing to solder or to assemble.
€616.55*
€649.00*
(5% saved)
ADDAC System - 203 CV Mapping
only 2 left
This is a new revision of one of our first modules, back from 2010. Now more compact in 6 HP and with an Offset CV input.The incoming signal amplitude is controlled by a [GAIN] attenuverter circuit allowing to attenuate the signal as well as invert its phase. A back jumper can set the maximum gain amount to either x1 (unity gain) or x10. DIY modifications can be made by changing its resistors. After the Gain an offset can be added to the signal, displacing the signal up or down (-5V to +5V) this can be adjusted using the [OFFSET] knob and CV input.When using no input using the [OFFSET] knob and CV input will generate an output between -5V and +5V.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€97.00*
ADDAC System - 216 Sum & Difference
available
There are two equal sections in this module labeled A and B.This module is a peculiar type of mixer that instead of just summing two input signals (X & Y), it also allows the possibility to subtract the two signals.It works both for audio and CV signals and hence allows for the possibility to get the diference of two CVs or cancel the phase of two audio signals. The resulting signal, of sum or subtraction, is then routed through a switchable (on/off) full rectification circuit labeled: Absolute. After this the gain of the mixed signal goes through another attenuverter labeled: Amplitude to control the resulting signal gain which, being an attenuverter, also allows the possibility to invert the incoming signal. After the Amplitude comes an AC/DC coupling switch followed by an bipolar Offset knob.Besides the normal output there’s also an inverted output for each of the A & B sections.The outputs of section A & B are also summed and sent to the Average Output.Using a single input, just the X or Y input, the module can also be used as a simple dual Attenuverter & Offset CV processor with full rectification and AC coupling options.Features:• 2 independent sections each with:• 2 inputs with gain attenuverters• Amplitude attenuverter and bipolar Offset• Absolute/Bipolar and AC/DC switches• Output and inverted output• 2 leds monitor the Output polarities and gain.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€130.90*
ADDAC System - 218 Attenuverters
sold out at the moment
Another addition to ADDAC200’s CV Utilities. This module features 3 independent Attenuverters each with its input, output and 13mm knob. White areas allow the user to write down what is connected to each channel.Channel 1 is normalled to Channels 2 and 3.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€80.00*
ADDAC System - 306 VC Transitions
only 1 left
ADDAC306 is a 5 channel multi-directional CV generator.You can think of it as a "sweet spot" controller, or a hands-on way of transiting from one state to another.Each of the five channels has MINIMUM, SPAN and DIRECTION controls, a common CV IN and a common TRANSITION CONTROLLER slider.MINIMUM sets the minimum channel voltage.SPAN sets the voltage range of the channel.It essentially sets the maximum voltage that can be output from the channel, relative to what the current channel MINIMUM is. For a given SPAN value, if the MINIMUM voltage is changed then the maximum voltage output from that channel will also change respectively.DIRECTION sets whether the voltage transition for each channel goes from MINIMUM to maximum, or maximum to MINIMUM.The TRANSITION CONTROLLER slider controls the transition from the minimum value (A) to the maximum value (B) or vice versa, according to the settings of each independent channel.Moving this slider generates 5 different voltages with 5 different ranges and directions. The transition can also be operated from a CV source at the CV IN, in which case the slider position acts as an attenuator for the incoming voltage.The maximum range of each channel can be set to either 5 or 10 volts, by 5 jumpers in the back of the module. Only positive voltages are generated at the output.Using the CV IN you can use two ADDAC306 modules to expand your control options to 9 voltage outputs under one common slider control.Use the VC Transitions to multiply the polyphony of a single CV sequencer by passing its outputs through the ADDAC207.VC Transitions makes for an awesome state transition controller. Plug its outputs to various CV controller parameters of your audio effects modules. Set the slider to position A, and set the minimum values for each channel. Then move the slider to position B and set the SPAN settings for each channel. Use the TRANSITION CONTROLLER slider to morph from state A to state B and backwards. Flip the DIRECTION switches to change the direction of the transition for each channel. Use the CV IN to automate the transition using LFOs, ADSRs or sequencers.Plug the output of your ADSR envelope to the CV IN and set the channels differently to get 5 different ADSRs from one common source.This module's development was based on an initial idea by Konstantine Fioretos.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€113.90*
ADDAC System - 309 CV To Expression
available
ADDAC309 CV to Expression allows a simple and straight forward connection between modular and effect pedals that features expression pedal TRS inputs.Instead of using an expression pedal into the effects pedal the user can use this module in between a CV source and the effects pedal to be controlled. This is a great way to control the available parameters on the effects pedals straight from a CV source.ADDAC309 features 2 channels each with a CV input with attenuator and a 1/4" jack output.This is a passive module, the power needed for operation is taken from the pedal power instead of the modular frame, this allows for perfect matching of the pedal’s operating voltage which can range from 3,3 V to 9 V.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€49.00*
ADDAC System - 703 Discrete Mixer
sold out at the moment
Here's the second module of our 700's Heritage Series.Inspired by Moog CP3 mixer, this is a totally discrete analog mixer and it's not, by any means, your standard breakfast mixer, although it can behave like one.This is a wolf in sheep's clothing. Despite its harmless looks there's a dark snarly soul behind that panel that wants to take your sounds into a realm of gritty, gnarly growls.Features:• 4 Independent channels with input jack and volume knob• 1 Feedback/gate knob• Master output volume knob• 6 Front panel trimmers allows user to adjust the Input resistor trimmer for each channel, feedback and master output• 1 Front panel trimmer allows to adjust the mix BiasDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€107.00*
ADDAC System - 713 Stereo Discrete Mixer
sold out at the moment
ADDAC713 is the stereo version of our 703 Discrete Mixer. Inspired by Moog’s CP3 mixer, this is a fully discrete analog mixer and it's not, by any means, your standard breakfast mixer, although it can behave like one.This is a wolf in sheep's clothing. Despite its harmless looks there's a dark snarly soul behind that panel that wants to take your sounds into a realm of gritty gnarly growls.This new version was initially thought of as a percussion mixer, with mono inputs and panning, to allow placing percussive voices in the stereo field, while keeping channel 4 in mono for low end sources like a kick drum or Bass. In the development process we slightly changed this initial idea, adding stereo inputs for the first 3 channels, but still kept the 4th channel in mono.All four [GAIN] controls go to extreme levels, the first 3 channels also feature [PAN] controls.Feedback is used to overdrive the whole mix. As the control is turned clockwise the sound will be clipped harder until it goes completely off, this happens as feedback is increased the audio bias reference also moves up, at extreme levels it offsets the whole signal upwards until it completely goes above the top rail clipping the whole signal hence the resulting gate effect.The [MASTER OUTPUT] sets the overall output gain of the mixer, the two LEDs monitor the audio output signal.The soft clipping switch engages an anti-click circuit which adds a low pass before the output, the switch allows 3 states: Soft low pass / Off / Hard low passFeatures:• Three channels with stereo inputs, gain and pan knob• One channel with mono input and gain knob• Feedback/gate knob• Master output volume knob• Soft clipping switchDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€137.50*
ADDAC System - 805 VC Signal Router V2
available
Inspired by our ADDAC701 VCO waveform mixing section, our new VC Signal Router also updates our legacy X-Fade/Panner to a stereo configuration that also allows 4 quadrant mixing.Featuring two dedicated X-faders and a stereo VCA that can also be used as a third X-Fader. All controls have their own CV inputs and dedicated Attenuverters for precision control.4 quadrant mixing is achieved by using the stereo Master as a X-fader between left and right channels, this way you can plug 4 audio sources and sweep/crossfade between each and any of them using the 3 x-faders. Plug any 4 sources (4 waveforms of a VCO, 4 LFOs, 4 envelopes...) and sweep through morph through or have them all mixed together.For other configuration types Left and Right X-fader channels can be routed through the Master stereo VCA or sent directly to the outputs. A stereo Direct input can also be routed through the Master VCA or sent straight to the outputs.The Mono Sum output always mix Left and Right outputs together allowing the possibility to use the module as a peculiar 6 channel mono mixer.It can be used for both Audio or CV Signals.Features:• 6 mono inputs• 2 dedicated X-faders with Control knob + CV Input and Attenuverter Each X-fader can be routed through the Master mix or straight into the outputs.• Master channel can be used as a stereo VCA or an X-fader• Stereo direct inputs can be routed through the Master mix or straight into the outputs.• Fully analog audio path with high quality/low noise VCAs.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€168.90*
ADDAC System - 813 Stereo Mixer+
available
ADDAC813 is a straight forward stereo mixer. Featuring 5 stereo channels, 4 of them with attenuators, a mono send/return path for parallel processing plus stereo and mono outputs.Four channels with stereo input and gain knob. Fifth channel with stereo input without gain knob, which are the prefered inputs to cascade several ADDAC813s when more channels are needed. Master Output controls the level of the Inputs mix. Two leds monitor the inputs mix.Mono Send / Return return path allows for easy integration of mono effects in a stereo chain. Plug your favorite module through it (filter, bbd delay, spring reverb...) or any mono pedal.The Return Gain works in parallel with the Master Output, just like regular wet / dry controls.The send output can be configured to be line or synth level via a jumper in the back.Stereo output sums the Inputs Mix with the Return signal.The Mono output is the sum of Left and Right outputsEffect PedalsUsing the send output at Line level, the user can connect the send output directly into mono effect pedals and have the pedals output connected directly into the return input without the need of an attenuator/amplifier module.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€130.00*
AI Synthesis - Analog Voltage Controlled Oscillator
available
The AI011 Analog VCO is a robust and stable analog Eurorack VCO. Using the legendary curtis 3340 IC, the Oscillator provides buffered Triangle, Square, and Ramp waveforms, as well as a triangle to sine wave shaper to provide a sine wave output. The Eurorack VCO features both Coarse and Fine tune knobs for easy tuning. Pulse Width Modulation is normalled to the PWM input jack, so PWM is controlled with the PWM knob, and when a jack is inserted, the knob serves as an attenuator. Volt per octave and FM input jacks are present, with an attenuator for FM modulation. The VCO is capable of both hard and soft sync. An expander jack is present at the rear of the module for use with future AI modules.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€127.00*
AI Synthesis - Harmonic Mixer
available
The AI022 Harmonic CP3 Style Mixer is a discreet mixer using no ICs. As gain increases harmonics and analog warmth are added. As gain increases more, distortion and phasing is added, creating new waveforms from old ones.The AI022 takes inspiration from the legendary Moog Modular CP3 style mixer, but updates it for eurorack and allows for user customization of the circuit. Many Moog Modular users attribute the CP3 mixer module to providing much of the warmth of the Moog Modular sound.An exposed Bias knob allows abuse of the circuit, and allows for faithful replication of incoming audio, or radical analog wave shaping and distortion. It is also possible to use the Bias knob to adjust a +/- 5V signal into a 0/+ or 0/- signal.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€64.00*
AI Synthesis - Line I/O Interface
available
The AI026 Eurorack Line Interface converts between +/- 2V line signals and +/- 5V Eurorack signals. This allows for the best headroom and highest quality when processing line signals with Eurorack modules, and vice versa.Features:• Stereo i/o• Left inputs are normalled to the right when no jack is inserted to the Right Input.• Volume control for Eurorack to line level signal conversion.• Volume control for line to Eurorack level signal conversion, with the ability to add gain/overdrive for non normalized signals.• Input and output jacksDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€99.00*
AI Synthesis - Matrix Mixer
available
The AI008 Matrix Mixer is an active, four in, three out matrix mixer with a summed output. The AI008 can be used to route any of the inputs to any of the outputs. This allows for the creation of feedback patches and other interesting routing, in addition to powerful "regular" signal routing. Common uses include mixing effects outputs into their inputs in order to create drones (or just good old fashioned feedback), mixing oscillators into their own PWM or FM inputs, modulating voltage controlled LFOs and other modulators into themselves, and other feedback patches. The AI008 Matrix mixes is a powerful way to expand any system!DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€107.00*
AI Synthesis - Mixer
available
The AI002 DIY Mixer Kit is an updated take on a classic utility audio or cv mixer. All three inputs have a level control, with full clockwise allowing full volume prior to the summing mixer. Perfect for adding audio inputs to a filter, or cv inputs to a cv input, and other mixing functions. This kit is ideal for those who know how to solder, but are still starting out in their DIY Synthesis journey.This diy mixer kit will not only familiarize yourself with IC Chips, Capacitors, and Resistors, it will also add a key utility module to your DIY Modular Synthesizer.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€52.00*
AI Synthesis - Quad VCA Mixer
available
The AI007 Eurroack Quad VCA Mixer is a compact, high quality, and flexible way to control voltage (audio or CV) in your modular system). Each of the four inputs are DC coupled, allowing the amplitude of CV signals as well as audio rate signals to be voltage controlled. The outputs are also normalled together into a mixer, allowing the AI007 Eurorack Quad VCA Mixer to be used as a voltage controlled mixer. Once a cable is patched into a VCA output that output is removed from the mixer signal, allowing each channel to be used independently, giving users four VCAs in total. A dedicated knob shapes the curve response from Linear to Exponential.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€127.00*
AI Synthesis - Stereo Matrix Mixer
sold out at the moment
The AI018 Eurorack Stereo Matrix Mixer is a compact 8-in, 8-out matrix mixer. A matrix mixer is used to route audio or cv signals from multiple sources to different destinations. There are sixteen potentiometers, with each potentiometer controlling the amount a given stereo input pair (1-4) will be sent to a given stereo output (A-D).A common usage for the AI018 would be as an effects send, with one or more inputs, and one or more effect inputs and outputs. Using the AI018 Stereo Matrix Mixer in this way, inputs can be sent to multiple effects, and the effects can be sent to each other, and even back into themselves, expanding the depth of the effects.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€142.00*
MIXER AND ATTENUATION
FLEXIBILITY AND CONTROL FOR YOUR DIY MIXING SETUP
The mixer is a fundamental component in any modular synthesizer setup. It plays a vital role in shaping and managing your sound by allowing you to combine, scale, and control multiple signals. For both audio and control voltage. Whether you're blending multiple audio voices into one harmonious output or fine-tuning several modulation sources, a mixer gives you the flexibility and control needed to realize your modular synth ideas. It can act as the central hub in your patch, where various signals meet, interact, and evolve.
At Exploding Shed, we offer a curated selection of mixers designed for both CV and audio applications. Some of our mixers are characterful, adding warmth, grit, or harmonic richness to your audio, perfect for those who enjoy a more colored or vintage tone. Others are ultra-clean and transparent, engineered for precision and clarity, which is especially useful when you require exact modulation values or when preserving the purity of a signal is a priority.
Mixers are versatile tools that open up countless creative possibilities. For example, you can layer several different oscillator waveforms, like saw, triangle, and sine waves, before sending them to a filter to shape the final tone. Or you can combine multiple square-wave LFOs at different rates to produce chaotic and evolving modulation patterns, mimicking the behavior of complex sequencers. Mixers also allow for subtle or dramatic control over levels, making them perfect for dynamic live performances and tuned studio patches alike.
You can also find channel strips for a modular mixing desk. With these mixers you can build your own mixer from the ground up. You can select a different compressor or your favorite equalizer for each channel so you can build the mixing console you need for your project.
SCALING AND INVERSION WITH ATTENUATORS AND ATTENUVERTERS
In addition to mixers, we also stock Attenuators and Attenuverters, which are perfect when working with sensitive inputs. These modules let you scale or invert your CV signals before routing them to oscillators, filters, or other modulation destinations. This level of control ensures that your patches behave as intended, especially when working with nuanced or unpredictable sources.
Whether you're just starting out or building a more advanced modular system, a reliable mixer and the right utilities to support it, is an absolute must-have in any Eurorack system.