4ms - Sampler
available
The Sampler plays stereo or mono .wav files from an SD Card. Samples are arranged into banks by placing .wav files into folders (each folder is a bank). A maximum of 10 samplers can be loaded in a bank, and there is a maximum of 60 bank (600 samples maximum total). Sample files are limited to 4GB each, which is over 6 hours at 44k/16b/stereo.• Hundreds of samples included on microSD card• Extremely quiet, low noise and low jitter design• Stereo or Mono outputA knob and CV jack selects the Sample to play, and the Start Position knob and CV jack control where in the sample playback will begin. The Length knob and CV jack determine how much of the sample is played back: from tiny grains, to percussive hits, to longer loops... or just the entire file.Pressing Play or firing a trigger into the Play Trig jack will play the sample. Holding the Play button down for a second will toggle looping.There's also a Reverse button and jack for backwards playback, and an End Out jack for synchronizing loops, or cascading sample playback with other events.To record samples, hold Play and Reverse for two seconds. Press Play again or fire a trigger into the Play/Rec Trig jack to start and stop recording. Each recording will create a new stereo 48kHz 24bit .wav file in the current bank's folder. Recordings can be as long as your card has the capacity for: a 256GB card is 18 days of continuous recording (432.9 hours). Audio data is split into maximum 4GB wav files on the microSD card.Included with the DIY Sampler Kit:• Main PCB• Faceplate• All components required for assembly (resistors, capacitors, diodes, ICs, sockets, headers, voltage regulator, jacks, buttons, SD card slot, potentiometers, knobs)• Pre-programmed and pre-soldered "DSP Brain-Board"• 16GB micro SD card (class 10) with 4ms Sample Pack 2022• SD adaptor• 10-to-16 pin power cable• M3 screwsFeatures:• Play button/trigger jack: Tapping the button or receiving a trigger starts/re-starts the sample• Sample CV/knob: select which sample within the channel's bank• Pitch CV and Pitch knob: playback pitch (-10 to +4 octave range)• Start Pos CV/knob: position in the sample to begin playback (loop start point)• Length CV/knob: playback time (loop end point)• Length knob at max: entire file is played• Length knob 50%-99%: 200ms - 5s of the sample is played (beginning at the Start Position)• Length knob <50%: Percussive decay envelope is applied to the playback (attack-only envelope if playing Reverse)• Length <1%: Tiny grains are played (can be used to sweep through sample file data manually)• Reverse button/jack: toggles forward/backwards• Bank button: selects channel's bank• Reverse+Start Pos button/knob combo allows for setting volume of playback• Audio Inputs: 20Hz to 10kHz (+/-0.1dB); -6dB rolloff @ 20kHz / 21V peak-to-peak maximum before clipping• Audio Outputs: 0Hz (DC) to 22kHz with maximum -1.8dB difference between file data and output / +10.5V to -10.5V maximum outputDIY-Kit-Type:This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€220.15*
New
Erica Synths - Pikocore XL
available
Pikocore XL is a Raspberry Pi–powered lo-fi music mangler originally developed by Zack Scholl.The Picocore has been reimagined by Erica Synths with a more playable, performance-ready design. The original Pikocore started life as a tiny pocket-calculator DIY device; Erica Synths worked with Zack to preserve the same functionality while giving it their signature hands-on interface and a sturdy aluminum enclosure.Features:• a lo-fi music mangler based on the Raspberry Pi Pico (brother of the nyblcore).• capable of holding 8 minutes of 8-bit 33 kHz monophonic samples.• powered by a single alkaline AAA battery for up to 3 hours or by powered by USB-C.• tempo-synced with a selectable BPM between 60 and 300, with samples mangled by beat-synced effects (stutter, retrig, gate, tunneling).• loaded with real-time effects like a resonant filter, timestretching, volume, and wavefolding.• sequenced with a 128-step sequencer with recording/playback• saved and loaded via EEPROM for instant patch recall.• able to load custom firmware, new samples, all through USB-C.• sync-compatible with Pocket Operators.• open-source, wonderfully hackable.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€194.00*
New
RYK Modular - Time Slice (Assembled)
available
NO DIY – THIS UNIT IS FULLY ASSEMBLEDTIME SLICE is a Quad-channel Eurorack looper and sampler for realtime time-warping and multi-track performance. Warp the fabric of time with Time Slice, a powerful quad-channel Eurorack audio looper and sampling workstation built for live performance and studio experimentation. Each of the four channels has its own large rolling buffer and dedicated FX chain – including H3000-style pitch-shifters, delay, reverb, tilt filter and wave-fold – plus a dedicated stereo mix output for final routing. Record, resample and overdub tracks, use 1-Shot sampler playback or enter a unique retrospective loop mode that captures what you just played even if you weren’t recording. Internal and USB storage let you load and save WAV files (with embedded WAV markers for multi-sample instruments), while extensive I/O – assignable CV inputs, per-track Trigger IN/OUT, MIDI and clock sync – keeps TIME SLICE tightly integrated with modular rigs and external gear. Inputs accept Line, Eurorack and Hot-Euro levels, and the module can ping-pong audio between tracks or record the stereo mix back into a buffer for creative multi-track manipulation. A bold retro scroll wheel and high-visibility display put hands-on control at your fingertips. TIME SLICE ships with a curated sample/loop library so you can start shaping time immediately.Features:• Quad-channel Eurorack looper/sampler with large rolling buffers per channel.• Dedicated Stereo Mix Output for mastering or resampling the master buss.• H3000-style real-time pitch-shifters on every track for dramatic time and pitch manipulation.• Per-track FX: pitch-shift, delay, reverb, tilt filter, wave-fold and more.• Internal and USB WAV storage with embedded WAV markers for multi-sample instruments.• Assignable CV inputs and per-track Trigger IN/OUT for modular control.• 1-Shot sampler mode, traditional loop mode, and unique retrospective loop mode.• Resampling/ping-pong routing – resample other tracks or record the Stereo Mix as a new track.• MIDI and clock-sync friendly; keeps impeccable timing in complex setups.• Accepts Line, Euro, and Hot-Euro levels for wide source compatibility.• Hands-on UI: large retro scroll wheel and high-visibility display.• Includes a starter library of samples, loops and effects to get you started.
€545.00*
Sebsongs - Sampler
only 2 left
The Sebsongs Modular Sampler DIY kits are now coming with presoldered surface mount components, making the DIY kit faster and easier to build.The Sebsongs Modular SAMPLER is an intuitive 12 bit audio recorder and manipulator designed for short loops and one shots. Sounds can be recorded either with the built in microphone or a mono input jack, which can handle anything from a regular laptop or smartphone to modular level signals. The SAMPLER has granular control of the recorded audio and you can play around with pitch, forward and reverse, start position and loop length (or connect cv/gate to any parameter) to open up a world of interesting sounds!The SAMPLER can be used in looping mode, where for instance time stretch like effects can be obtained easily by modulating the start parameter, or in one shot mode where the reset input is used to trigger playback of the recorded audio and the SAMPLER can function as a drum sample player.The maximum recording length is around 3.5 seconds in the highest sample rate (pitch control fully forward or reverse). If you lower the pitch you get longer recording time. Change the pitch while sampling to obtain pitch fluctuations and tape stop effects.Sound can be recorded either with the built in electret microphone or via mono input jack*. The audio input has enough gain for amplifying regular laptop or smartphone headphone outputs, and the input can also handle modular level signals.* If connecting stereo signal from a laptop / smartphone via either TS or TRS mini jack cable it is advisable to pan the source fully left to avoid distortion.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€187.00*