ADDAC System - 200CT Cable Tester
available
Introducing ADDAC’s Cable Tester, a desktop utility that provides a reliable means to test the integrity of both mono jacks and ribbon cables, ensuring that every connection is secure and electrically sound.Individual Wire Testing - Featuring the ability to test each wire within the ribbon cables independently with dedicated LEDs for every wire, providing a clear visual indication of the status of each connection, wires are also tested against their neighbouring wires to detect shorts.BUSBOARD MONITORThe busboard monitor leds allows the user to check the state of the busboard power lines as well as the special CV/Gate functions. If the busboard has no +5v supply the led will be off likewise for the CV/Gate functions if not in use.This is a desktop device, we provide a long power cable so that it can still be plugged into your rack.As a safety precaution only power this board when you need to test a cable. Leaving it ON at all times can lead to unintended problematic misuses which, in a worst case scenario, can shorten your Eurorack PSU,! WARNING !DO NOT POWER MODULES FROM THE TEST SOCKETS!!Compatible with all ADDAC System ribbon cables (power, expansions and interconnectivity: 112, 213, 807).Also compatible with any standard Eurorack power ribbon cable (2x5 to 2x8 or 2x8 to 2x8).! WARNING !NOT ALL MANUFACTURERS FOLLOW THESE STANDARDS!ALLWAYS NOTICE THE ORIENTATION OF THE HEADERS IF YOUR CABLE DO NOT FOLLOW THE STANDARD THEN MOST PROBABLY IS NOT COMPATIBLE.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€40.00*
Befaco - JumpSkiff
only 1 left
The JumpSkiff is a lightweight and portable 98HP skiff with integrated bus board and powersupply. It is made from lightweight and flexible materials including a PCB base (which doubles as the bus board) and side panels, acrylic end panels and aluminium rails.Features:• Connectors: 14x IDC 16 pin• Size: 98HP• Depth (inc. connector): 52mmDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€177.31*
Sinusoda - Bubbles
sold out at the moment
Ultra Low Noise filtering & safety technologies we’ve used in Juice. You can add up to two Bubbles to your Juice Powerboard.Bubbles can also be used with other power solutions by connecting the one header with a ribbon cable to your power unit. More information available at https://sinusoda.comNo power brick included - you will need to buy power brick separately (Power brick is needed for Juice & Straw to work, Bubbles is an expander for Juice, and only one power brick is needed for the whole system).Dimensions: 226 x 86 x 19 mm
€65.00*
Sinusoda - Empty Can (Unsassembled, Black)
sold out at the moment
Sinusoda - Empty Can (3U, 52 HP) - Black (unassembled)Empty Can is Sinusoda’s 3U 52 HP case without power supply. Comes in parts and ready for self-assembly. Additional vertical and horizontal connectors of the casing system included. It’s a starting point for a truly modular case for modular synths.Side blinds can be cut into blank panels revealing more space - additional 4 hp from the top on both sides, and up to 14 hp from the sideway mount.For more information on the Sinusoda modular casing system visit the Sinusoda Website.Features:Dimensions: 325 x 130 x 85 mmCase depth: 70 mm without powerboard, and 56 mm with powerboardWeight: 0,72 kg
€89.00*
Sinusoda - Juice & Straw
only 1 left
Juice Powerboard is Sinusoda’s Ultra Low Noise power supply solution offering up to +12V: 3A / -12V: 1.5A / +5V: 2A of clean power for your synths. Several Juices can be connected together in series for more power - 2 Juices can be powered from one 96 W Brick, and 4 Juices with 200 W Brick.Every output is actively filtered giving your modules really clean power. There are also various protective measures so that even if something unexpected happens your precious modules should be safe. Precise information and full technical data sheet available at https://sinusoda.comNo power brick included - you will need to buy power brick separately.Dimensions:Juice: 226 x 86 x 19 mmStraw: 3U, 3 HP, 22 mm Depth
€197.00*
Sinusoda - Power Brick 60W
only 1 left
Sinusoda power bricks are available as 60 W for smaller setups and 96 W for bigger setups.60 W Brick is the recommended power brick for a single Juice & Bubbles unit. It comes as the standard brick with all our products. More information at https://sinusoda.comThe plug is 5,5 mm outside, 2,5 mm inside, center positive (Barrel 5525).
€29.00*
Sinusoda - Slim Can (Unsassembled, Black)
only 1 left
Sinusoda - Slim Can (1U, 52HP) - Black (unassembled)The Slim Can is Sinusoda’s 1U 52 HP expansion that can be mounted together with The Can. It’s made to fit Intellijel format 1U modules. Comes in parts and ready for self-assembly. Vertical connectors included for easy expansion.You can connect any amount of Sinusoda’s Empty Cans or Slim Cans to add more HP to this case.It’s meant as an expander so it comes without the side blinders.For more information on the Sinusoda modular casing system visit the Sinusoda Website.Features:Dimensions: 328 x 46 x 85 mmCase Depth: 70 mmWeight: 0,32 kg (no power brick included)
€78.00*
Sinusoda - The Can (Unsassembled, Black)
available
Sinusoda - The Can (3U, 52HP, Juice, Straw, 60W Brick) - Black (unassembled)The Can is Sinusoda’s 3U 52 HP case that comes with Juice Powerboard, Straw power inlet and 60W power brick. Comes in parts and ready for self-assembly. Additional vertical and horizontal connectors of the casing system included. It’s a starting point for a truly modular case for modular synths.You can connect any amount of Sinusoda’s Empty Cans to add more HP to this case.Juice Powerboard is Sinusoda’s Ultra Low Noise power supply solution offering up to +12v: 3A / -12v: 1.5A / +5v: 2A of clean power for your synths. Several Juices can be connected together in series for more power.Straw power inlet has a USB charging port for your mobile devices, midi devices or lamps.Side blinds can be cut into blank panels revealing more space - additional 4 hp from the top on both sides, and up to 14 hp from the sideway mount.For more information on the Sinusoda modular casing system visit the Sinusoda Website.Features:Dimensions: 325 x 130 x 85 mmCase depth: 70 mm without powerboard, and 56 mm with powerboardWeight: 0,9 kg (power brick included)
€255.00*
Sinusoda - The Can (Unsassembled, Grey)
only 1 left
Sinusoda - The Can (3U, 52HP, Juice, Straw, 60W Brick) - Grey (unassembled)The Can is Sinusoda’s 3U 52 HP case that comes with Juice Powerboard, Straw power inlet and 60W power brick. Comes in parts and ready for self-assembly. Additional vertical and horizontal connectors of the casing system included. It’s a starting point for a truly modular case for modular synths.You can connect any amount of Sinusoda’s Empty Cans to add more HP to this case.Juice Powerboard is Sinusoda’s Ultra Low Noise power supply solution offering up to +12v: 3A / -12v: 1.5A / +5v: 2A of clean power for your synths. Several Juices can be connected together in series for more power.Straw power inlet has a USB charging port for your mobile devices, midi devices or lamps.Side blinds can be cut into blank panels revealing more space - additional 4 hp from the top on both sides, and up to 14 hp from the sideway mount.For more information on the Sinusoda modular casing system visit the Sinusoda Website.Features:Dimensions: 325 x 130 x 85 mmCase depth: 70 mm without powerboard, and 56 mm with powerboardWeight: 0,9 kg (power brick included)
€255.00*
Sinusoda - Two Pack Slim Can (Unsassembled, Black)
only 1 left
Sinusoda - Two Pack Slim Can (1U, 104 HP) - Black (unassembled)The Two Pack Slim is Sinusoda’s 1U 104 HP expansion that can be mounted together with Four Pack. It’s made to fit Intellijel format 1U modules. Comes in parts and ready for self-assembly. Vertical connectors included for easy expansion.You can connect any amount of Sinusoda’s Empty Cans or Slim Cans to add more HP to this case.Features:Dimensions: 592 x 46 x 85 mmDepth: 70 mmWeight: 0,552 kg (no power brick included)
€147.00*