ADDAC System - 107 Acid Source
only 2 left
We started this module with the idea of developing a complex drum source. However, somewhere along the process we noticed how much better it performed as a synth voice and simply embraced this lucky accident.It features a VCO with a [FREQUENCY] and [FINE TUNE] knob plus a dedicated CV Input and Attenuator knob (tunable over 4 octaves). The VCO waveform output is achieved by selecting either a Triangle or Saw through a switch. The selected waveform can then be mixed/balanced against the square wave. The resulting mix is then sent to the Filter.The Filter features a [CUTOFF] and [RESO] resonance knob plus a Cutoff CV Input and Attenuverter knob.A 3 position switch is used to select the filter type: Highpass, Bandpass or Lowpass. The resulting output is then sent to the VCA.The VCA features an Input with [INPUT GAIN] knob which at maximum can amplify the incoming signal by a factor of 2.This is a very important control, it accepts any signal Trigger, Gate or CV. Whatever input is plugged in the signal is then fed through an AD with a very short attack and controllable decay through the [VCA DECAY] knob plus the CV Input and Attenuverter knob. The resulting slewed signal is then used to control the VCA gain. This signal is also sent to the CV OUTPUT as well as the LED monitor.The Accent input adds to the Input signal creating a different amplitude output. The CV OUTPUT is normalled to the Frequency and Cutoff inputs.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€202.30*
AtoVproject - cDVCA (Black)
available
cDVCA or class-D VCA is a new kind of VCA based on an entirely novel concept that is inspired from class-D amplification technology. This is not a transparent VCA and brings a lot of character to the sound.The first VCA that tracks 1V/octConcept: The input signal is turned into an ultrasonic PWM signal (~34kHz). The PWM is scaled to the desired amplitude and then filtered back down to the original signal.The twist: The PWM frequency can be lowered down into the audio spectrum and the frequency can be controlled via its 1V/oct input allowing for crazy waveshaping that tracks your melodies.The drive controls an innovative clipping method that does not rely on overdriving any circuitry and therefore results in distortions with a very defined character.The signal then goes into a 1 pole VCF/tone circuit that allows to keep things under some amount of control as the harmonics produced by this module can be very aggressive.With no input the module generates a simple square wave and therefore can be used a simple synth voice (VCO→VCA-VCF)DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€185.00*
AtoVproject - cDVCA (Silver)
only 1 left
cDVCA or class-D VCA is a new kind of VCA based on an entirely novel concept that is inspired from class-D amplification technology. This is not a transparent VCA and brings a lot of character to the sound.The first VCA that tracks 1V/octConcept: The input signal is turned into an ultrasonic PWM signal (~34kHz). The PWM is scaled to the desired amplitude and then filtered back down to the original signal.The twist: The PWM frequency can be lowered down into the audio spectrum and the frequency can be controlled via its 1V/oct input allowing for crazy waveshaping that tracks your melodies.The drive controls an innovative clipping method that does not rely on overdriving any circuitry and therefore results in distortions with a very defined character.The signal then goes into a 1 pole VCF/tone circuit that allows to keep things under some amount of control as the harmonics produced by this module can be very aggressive.With no input the module generates a simple square wave and therefore can be used a simple synth voice (VCO→VCA-VCF)DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€185.00*
Befaco - Kickall
only 2 left
Kickall is a 6HP compact synth voice that features everything needed to make a big fat Kick sound. A stable VCO that tracks V/Oct, a couple of VCAs, envelopes for volume and pitch and an aggressive waveshaper.The module has been designed with a kick synthesis patch in mind.The audio path consists of a sinewave oscillator that passes across a Square Waveshaper and two VCA’s. The first VCA is for the Volume envelope. The second VCA is dedicated to general volume. Thanks to his CV input, it is possible o apply accents or affects the dynamics of notes. Feeding this input with audio generates a basic AM operation expanding the sonic range of the module.In the control path, KickAll has two envelope circuits to modulate the first VCA oscillator’s pitch. Both envelopes are fired at the same time manually or via dedicated trigger input.Through its Tune input, KickAll tracks eight octaves with high accuracy. Plug your favourite sequencer or CV source to create patterns out of the kick range, or feed it with an audio signal, for frequency modulation Fx.Features:• Accurate V/oct tracking.• CV controllable Sine to Square waveshaper.• CV controlled envelope decay for main VCA.• CV control over General volume (after VCA).• Wide range pitch envelope control.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€135.66*
Eowave - Weather Drones
sold out at the moment
Eowave's Weather Drones is an all in one drone voice for eurorack modular. The Weather Drones can be self patched, or used with other eurorack modules via CV and trig inputs. Check out this video. The architecture of the module is as follows, some of which is pre-patched:• Digital tri wave oscillator, controls are freq, spread (adds more triangle waveforms, up to 8), character (wave folder), FM with attenuator• LFO with square and tri wave out• Filter with cutoff and feedback, mod input with attenuator and second mod input without• AD envelope with level attenuator• Random sample and hold noise (driven by square wave LFO) with slew• VCAVersion 1.5 is a full kit with SMD parts presoldered. This version is technically updated to the previous versions and all SMD components are already pre-soldered. All THT parts to be soldered by you.* Before you ask yourself: the big potentiometer is delivered without nut. It's ment to be like this.This is a Do-It-Yourself kit, not an assembled module.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€148.75*
Hex Haus - HEX cor
available
HEX cor is a digital polyphonic synthesizer with a capacitive keyboard, potentiometers for signal modulation and an adaptable looper that through its unusual shape explores new ways of interaction and sound synthesis.Features:• Capacitive pads• Recording button• Octave• Waveform• Decay• Loop speed• Loop length• Sync switch• Header pins• 3,5 mm headphone jack output• USB C power portDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€97.37*
Neutral Labs - Elmyra 2 (Desktop)
available
This is the standalone version of Elmyra 2. Elmyra 2 is a 4-voice digital/analog hybrid platform for microtonal sonic exploration, capable of creating anything from lush ambient soundscapes to gritty droning textures and shrieking noises, available as a 42 HP Eurorack module or semi-modular desktop synth. With 31 modulation targets, 4 polymetric sequencers, delay, additional per-voice effects, a choice of various filters, as well as onboard LFOs and utilities, it is essentially a purpose-built small modular system in itself. A set of preset cards (included) or electronic components like capacitors or diodes can be plugged into the front panel in order to change the sound character.Features:• 4 independent voices activated by touch or CV• wavetable-based complex oscillator engine, up to 12 oscillators in total, 1V/octave compatible• chromatic mode makes chords and harmonic sounds possible, microtonal scales supported• 41 patch points• 31 modulation targets• touchpads with analog envelopes that can be used as modulation sources• resonant filter switchable between:• boomy and aggressive multimode 2-pole state variable filter (low-pass, band-pass, high-pass)• creamy 4-pole low-pass ladder filter• delay with unhealthy amounts of feedback• lo-fi reverb• analog OUCH circuit: a unique combination of destructive distortion, waveshaping and filtering• sonic character can be customised by using special preset cards (set of 4 included) or components like diodes that can be plugged into the front panel• preset cards can be used with other Neutral Labs modules• external audio can be processed via audio input• 9 per-voice modulations and effects:• unison detune• dual sub-oscillators• saturation• bitmangler• sample rate reduction• noise• high-pass filter• low-pass filter• 2 LFOs: 1 sine, 1 complex morphable• 4 sequencers with arbitrary step length per voice (up to 128), allows polymetric structures• delay time and LFOs can be clock-synced or unsynced (tap tempo is also possible)• utilities• dual attenuator/buffered multiple/voltage generator• CV summing circuit• case made of plant-based bioplastic and native German oakwood• boutique synth handmade in GermanyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€379.00*
Neutral Labs - Elmyra 2 (Eurorack)
available
This is the Eurorack version of Elmyra 2. Elmyra 2 is a 4-voice digital/analog hybrid platform for microtonal sonic exploration, capable of creating anything from lush ambient soundscapes to gritty droning textures and shrieking noises, available as a 42 HP Eurorack module or semi-modular desktop synth. With 31 modulation targets, 4 polymetric sequencers, delay, additional per-voice effects, a choice of various filters, as well as onboard LFOs and utilities, it is essentially a purpose-built small modular system in itself. A set of preset cards (included) or electronic components like capacitors or diodes can be plugged into the front panel in order to change the sound character.Features:• 4 independent voices activated by touch or CV• wavetable-based complex oscillator engine, up to 12 oscillators in total, 1V/octave compatible• chromatic mode makes chords and harmonic sounds possible, microtonal scales supported• 41 patch points• 31 modulation targets• touchpads with analog envelopes that can be used as modulation sources• resonant filter switchable between:• boomy and aggressive multimode 2-pole state variable filter (low-pass, band-pass, high-pass)• creamy 4-pole low-pass ladder filter• delay with unhealthy amounts of feedback• lo-fi reverb• analog OUCH circuit: a unique combination of destructive distortion, waveshaping and filtering• sonic character can be customised by using special preset cards (set of 4 included) or components like diodes that can be plugged into the front panel• preset cards can be used with other Neutral Labs modules• external audio can be processed via audio input• 9 per-voice modulations and effects:• unison detune• dual sub-oscillators• saturation• bitmangler• sample rate reduction• noise• high-pass filter• low-pass filter• 2 LFOs: 1 sine, 1 complex morphable• 4 sequencers with arbitrary step length per voice (up to 128), allows polymetric structures• delay time and LFOs can be clock-synced or unsynced (tap tempo is also possible)• utilities• dual attenuator/buffered multiple/voltage generator• CV summing circuit• case made of plant-based bioplastic and native German oakwood• boutique synth handmade in GermanyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€329.00*
Patching Panda - BD-Z
available
BD-Z is a versatile kick drum module for Eurorack system focus to design a wide range of bass drum percussive sounds. The implementation of thru-zero FM/PM BD-Z can deliver an an immense variety of textures and harmonics, it has an amount of control of the modulation, input to preserve the primary kick drum sound or not. Check out this video from Superbooth 2021.Also the implementation of amplitude modulation to the sound core it can add more harmonics from the modulation source to be able to shape the sound, transform and morph it into many other drums sounds like bongos, congas, etc. Attention carefully was considered to maintain the signal gain always punchy so when the amplitude decay or the distortion is fully open it won't get out of control.The distortion can be subtle or aggressive, it has a dedicated accent like the vintage style drum machines to add dynamics to the rhythms. Features two amplitude envelopes out to control other utilities with the shape of the signal. BD-Z is a powerful Kick drum module with many modulation possibilities!DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€202.00*
Patching Panda - Hatz v2
only 2 left
Hatz v2 is an all-analog module designed to help you sculpt all sorts of hi-hat and percussion sounds. At the core of the module are two noise generators: complex (LFSR) noise and (LOGIC) noise metals. Both channels are equipped with 2-pole filters, and a VCA + envelope combination. A CV-able Decay control for the Open Hi-Hat channel offers a handy solution for more rhythmic animation.New in version 2, Hatz offers a Texture control with dedicated CV input. This control offers a wide range of distinct noise textures, making Hatz great for everything from classic, clicky hats to metallic snares, filtered clangs, and more. V2 also sports revised envelopes and a vastly improved signal to noise ratio, making for a significant upgrade to this already stellar module. Here is a video demo.Features:• Analog hit-hat module combining 2 kinds of noise heart ❤ complex (LFSR) noise and (LOGIC) noise metals• 2 pole filter for each individual channel with CV• Vintage drum machine accent style with choke function• Linear and exponential fall selection in both channels• Decay control with CV in the open hat• Hold intput for manually open the envelope via gates and CV• 2 leds indicatorDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€184.45*
RYK Modular - Vector Wave
available
FM & Vector Synthesis - Two icons of the '80s in one unit!Introducing the new Vector Wave from RYK Modular bringing together the awesome power of 16 oscillator FM, combined with Vector synthesis OR true multi voice polyphony.The Vector Wave is a feature packed compact Eurorack module, which can be used as a stand alone synth-voice without the need for external VCA,ENV, LFOs etcWARNING! To build the kit you MUST have the following:• Accurate and stable 5.00V reference source to calibrate the module• Flux pen, or liquid flux• Two mini clamps• Clean high quality 2/3mm tip solder iron [chisel type recommended]Features:• 16 oscillators, divided into 4 banks, oscillators can freely configured into series or parallel combinations for complex FM or additive synthesis• A cute Vector Joystick for morphing between oscillator banks, for cool performance timbre sweeps and sonic movementVectors can be recorded from the joystick and replayed from trigger sources, or animated from external or internal modulation sources• Super cool retro Big-Pixel screen, ideal for nostalgia freaks or the visually impaired• Wave Warping brings grit and aggression to the FM synthesis with oscillators continuously variable between Sine,Tri-ish Saw, Pulse waveform• Wave Folding for subtle to extreme sonic bending• Two Envelope generators [per voice in polyphonic modes], and two LFOs with all controls assignable as modulation destinations• Intuitive Modulation Slot patching from external and internal sources to be routed to any parameter within the Vector Wave• 30 User Voice storage spaces for storing your synth masterpieces to internal memory, enabling you to impress your friends at a later date• Thee modes of oscillator bank allocation Monophonic Vector, and Polyphonic Voice, and Multitimbral Polyphonic• MIDI input for a spaghetti-free Polyphonic setup, velocity, aftertouch and MIDI CCs avail- able as modulation sources• Slim but handsome Expander Module also available that adds 3 more V/oct and Gate inputs, for maximum mutli-voice multitimbral melodious mayhem!PLEASE NOTE THE KIT IS ONLY SUITABLE FOR EXPERIENCED BUILDERS.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€284.41*
RYK Modular - Vector Wave Expander
sold out at the moment
V/Oct and Gate expander for RYK Vector Wave.The slim but handsome Vector Wave Expander module, adds 3 extra V/Oct and Gate inputs to the Vector Wave.Using Multi Timbral mode, these extra inputs can control 4 separate monophonic synth voices within the Vector Wave.This is a great way to add multi voice synth parts in a compact and unique Eurorack module!
€73.78*
Wirehead Instruments - Freaq FM (DIY - Blue LEDs)
only 1 left
This is the DIY version of that machine with blue LEDs. The Freaq FM is an 8-bit digital synthesizer for your desktop featuring dual 2-op FM voice architecture with multiple waveforms, LFO and modulation envelopes with a 16-step generative sequencer.From soul-soothing sine waves to multiverse-shredding modulated distortion, slapping bass lines to soaring arp leads, the Freaq FM is a powerhouse of sound design packaged with a melodic and intuitive generative sequencer inspired by the likes of Elektron, Intellijel & Music Thing.With 2 channels of liquid FM sounds, it plays great by itself or synced with your favorite external gear.Features:• 2 independent 2-operator FM voices• Multi-mode FM ratios & operator waveforms• Attack/Decay modulation envelope per voice• LFO per voice with multiple waveforms and destinations (envelope attack, decay & depth, FM ratio, amop decay)• 2/1.5 track polymetric sequencer with 1-16 steps per track• Parameter-lock recording of synth parameters• Multiple generative algorithms• Global tonic & scale (Ionian (Major), Minor (Dorian), Pentatonic, Phrygian, Octaves, Fifths)• Tap-tempo control• Sync input & output (Eurorack & Volca/PO compatible)• Audio output (14-bit DAC)• 7-12V DC or USB poweredDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€151.13*