DIY Kits
available
Total flexibility for the Befaco 7U or Intellijel cases rear connectors jacks. The channels are reversible and can be used independently for input or output.4 Inputs or Outputs (per module) can be obtained by “AND” cables. Independent tip and ring attenuators are selectable for each channel to convert the modular input level to line output level.Features:• Selectable atenuator per channel.• Fully compatible with Intellijel’s 7U and Palette cases.• 1U Intellijel format.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
available
VC ADSR adds voltage control to a conventional attack, decay, sustain and release envelope. Its stage gate outputs let other modules respond as the envelope progresses. Features: • CV and manual controls for the envelope stages • Individual stage gate outputs • Manual trigger button and gate/trigger input • Adjustable response curves • Width [HP]: 8 • Depth [mm]: 26 • Format: 3U • Current draw +12 V [mA]: 55 • Current draw -12 V [mA]: 25 • Panel / Color: Black Alu • DIY Level: Medium DIY-Kit-Type: THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
VCMC translates modular control voltages and gates into MIDI messages. Its faders, buttons and on-board editing make it possible to control external instruments and software directly from a patch. Features: • Eight faders and eight buttons with assignable control • Ten CV inputs and eight gate inputs • Class-compliant USB MIDI and five-pin DIN MIDI • OLED display for editing and configuration • Width [HP]: 20 • Depth [mm]: 30 • Format: 3U • Current draw +12 V [mA]: 64 • Current draw -12 V [mA]: 12 • Panel / Color: Black Alu • DIY Level: Advanced DIY-Kit-Type: THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
An accurate voltage source and precision adder. Voltio fits somewhere between a music tool and a piece of electronics lab gear.It generates voltages equivalent to all the notes on the 12-tone equal temperament scale throughout a ten-octave range, with an intuitive two-knob interface.The Precision Adder In, lets you sum Voltio’s Out with external voltages.Additionally, the front panel banana connectors let you plug standard multimeter probes for hands-free operation on electronics lab.Use it to transpose Oscillators and sequences in a musical way or as a reference to calibrate your analog gear.Features:• Easily adjust your oscillators in known intervals.• Transpose Musical phrases from sequencers, arpeggiators, or any other notes source.• Calibrate oscillators and filters on your DIY projects or during analog gear maintenance.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
The Mutes mk2, developed in collaboration with Ben Wilson (aka DivKid), is a powerful upgrade to the original performance muting module. Now using VCA-based technology, it delivers improved signal integrity, reduced noise floor, and zero bleed, while preserving the smooth, vactrol-style response. Each channel features a performative three-way switch (momentary–off–on), perfect for live dub-style FX routing and dynamic signal control. Mutes Mk2 enables signal splitting to multiple destinations, expanding your modular performance possibilities. This updated version includes both a standard 3U panel and an additional Intellijel-format 1U panel, allowing for versatile mounting in various Eurorack setups.Features:• LEDs to visualise signals• 3 way momentary – off – on switching• Buffered and cascading normalising of inputs• Black metal panel• VCA based mutingDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The Output Bus is your ultimate output module: Presented by DivKid and Befaco, meant to be the last link in your modular chain!Inspired by pro audio and studio summing units the Output Bus allows for summing style mixing, external gear integration, soft clip limiting, flexible output types, headphone monitoring and level visualization.The module works great mixing all your other mixers in your setup, to return mono or stereo FX into the master bus and for bringing in external stereo line level gear with ease. All of this in just 8HP while also being able to visualize your final levels, output appropriate signals on the right cable type and monitor in headphones.Features:• Six stereo inputs.• Line/synth selector in input six.• Modular level minijack out.• 6,5 mm Jack balanced out.• Minijack and 6,5 mm phones out.• Led Vu-meter.• Soft clipping circuit at main output.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Stereo Strip takes the idea of a channel strip and makes it modular. We hope that by bringing this long-established component of the audio engineering world into the Eurorack environment and by adding CV control over its key parameters that you will find new, creative ways to use it in your patches!It features stereo inputs and outputs for audio or CV with EQ, voltage controlled panning, stereo VCA, performable mute and input/output level switching for Eurorack or line level uses. Abusing the input level switching allows for some musical, modulate-able and highly shapeable distortion sounds too.Stereo Strip was designed to be a creative part of a modular patch. Creating stereo images from mono sources, shaping and modulating existing stereo images, synthesising stereo pseudo ring modulation, sweetening FX with EQ or drastically wave shaping your oscillators, creating send FX routings with benefits or it can simply be used as a channel strip at the end of chain in a patch.The addition of line level gain boosting (for the input) or reduction (for the output) allow it to work as a stereo input or output interface for external gear with the advantage of the VCA, panning and the EQ to shape the sound. Experiment with bringing external gear into the Eurorack format and then shape and modulate those sounds them on the way in!Try patching Stereo Strip anywhere you would place a VCA in a system and/or explore its EQ and voltage controlled panning, which are rarer additions to the sound sculpting options for the Eurorack format.This module is designed in collaboration with Ben Wilson aka Divkid.Features:• 3 band EQ• Panning (manual and voltage controlled)• VCA level control (manual or voltage controlled)• 3 way performance muting (on-off-momentary)• Soft clipping limiter (distortion!)• Line level input and/or output adjustmentDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
This is our new collaboration with Robin Vincent aka Molten Music Technology. A Stereo bypass module to gate control the send of your signals to your favorite effect!Molten bypass features a hard/soft bypass control, to hard cut the return of your effect or allow the long tails of your reverb to stay after you bypass the effect. Also a gate/latch control to use either triggers or gates for control and a gain control for the returned signal.Features:• Full stereo signal path• DC coupled• Hard or soft bypass selection• Gate or Latch possibility• Manual or Gate control• Gain control over the returnDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Motion MTR allow you to mix, attenuate and invert signals while having clear visual feedback of their levels.Each channel can function as:• Audio level control with VU meter• CV attenuator with voltage meter• CV inverter with voltage meterEach input is normalled to 10v, so you can use each of them to generate fixed voltages. Also, the outputs of channels 1 and 2 are summed into Out 3 to be used as a mixer. Patch it wildly to make it work as an attenuverter with offset, as a mixer, a VU meter or a combination of them all!This module is designed in collaboration with Robin Vincent from Molten Modular.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Motion MTR 1U mixes, attenuates or inverts signals with visual feedback for each channel. Normalled inputs let the controls produce fixed voltages when nothing is patched in. Features: • Three channels for audio level or CV scaling • Meters for signal level and polarity • Normalled 10 V sources for offsets • 34 HP in Intellijel 1U format • Width [HP]: 34 • Depth [mm]: 30 • Format: 1U • Current draw +12 V [mA]: 110 • Current draw -12 V [mA]: 30 • Current draw +5 V [mA]: 0 • Panel / Color: Black Alu • DIY Level: Medium DIY-Kit-Type: THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Random8 generates eight channels of stepped or smoothed random voltage for generative patches. Capturing a loop turns an evolving sequence into repeatable modulation or pitched material. Features: • Eight independently generated 0–10 V control voltages • Loops from one to 32 steps • Per-channel quantization with 16 scales • Supplied assembled and ready to patch • Width [HP]: 8 • Depth [mm]: 30 • Format: 3U • Current draw +12 V [mA]: 60 • Current draw -12 V [mA]: 12 • Panel / Color: Black Alu • DIY Level: NOT DIY
available
Cosmos is a new kind of module that will help you to creating complex modulation, sounds, patterns with ease and will lead you to new sounds territories.Inspired by early analog computers, Cosmos is a unique, innovative, very flexible and fully analog module allowing it to be used as: VCO, LFO, Ring Mod, Polarizer, “VCA”, “LPG”, Phase Lock Loop, Cross-Modulation, Minimum, Maximum, Logic Gates, Waveshaper, Complex gate generator, Fuzz, Distorsion, Gate extractor, Trig extractor, Gate generator, Voltage generator, Trig Generator, comparator, window comparator, complex comparator, Half-Rectifier, Full-Rectifier, Inverter, Buffered Multiples, Mixer, Difference, Compressor, Sidechain, compressor, VC Clipper, VC Switch, Clock doubler, Envelope follower, and more.With its wide fields of application Cosmos can replace many modules but it will also bring new colors to your palette thanks to its unique character. This makes Cosmos the ideal module whether you have a small case or a big system. 100% analog and with an intuitive interface Cosmos is also very easy to use, no menu and button combo problems.Inspired by the past and crafted for the future, 100% analog Cosmos was not only thought to be the center of any system but also to blend perfectly with the rest of your case to form a consistent and coherent system.Cosmos was designed not only to be a swiss army knife module but also to push you to explore and you help create new sounds and explore sonic territories that were previously unattainable.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
DBM-S is the simplest yet ultimate 1U solution to distribute incoming signals to up to 8 destinations without signal loss, distortion, or interference.DBM-S clever design provides you maximum flexibility, use it a dual channel to create 4 buffered copies of 2 signals or as single channel and get up to 8 buffered copies of the same signal!Build with high-quality components for low noise and high accuracy, DBM-S create perfect copies of the original signal even for pitch CV. After all, quality isn't just a feature, it's our commitment.We believe that form must follows function, but great design blends them seamlessly. With our black and gold signature, DBM-S is not just a high quality utility, it’s a part of a system where each part contributes to the overall strength and quality of this system.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
DC is a unique and innovative module that combines the strength of both Averager and Unity Gain mixers without their weaknesses. Along with some additional unique features that make it stand out from other mixers on the market.To create DC we had to rethink the mixer, start from scratch, try new design, prototype many circuits and fail in order to succeed. The result is DC a new type of mixer that offer low noise floor, stable output signal and mix accurately signal without introducing any distortion, clipping, attenuation or unwanted noise and those regardless of the number of inputs signals or their gain.We called this new mixer design a «Combinator,» and the name «DC» stands for «Dual Combinator.» This versatile mixer can function as a dual-channel, mixing up to 3 inputs into a single output, or as a single-channel, allowing up to 5 inputs to be mixed into a single output.We put time and effort into the design of DC because we think that it is an essential module in any Eurorack system. It offers a ratio size, functionality, simplicity that no other mixer offers.DC may seem like a simple utility module, but make no mistake, small things done well can make a big difference.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
DC-S is a unique and innovative module that combines the strength of both Averager and Unity Gain mixers without their weaknesses. Along with some additional unique features that make it stand out from other mixers on the market.To create DC-S we had to rethink the mixer, start from scratch, try new design, prototype many circuits and fail in order to succeed. The result is DC-S a new type of mixer that offer low noise floor, stable output signal and mix accurately signal without introducing any distortion, clipping, attenuation or unwanted noise and those regardless of the number of inputs signals or their gain.We called this new mixer design a «Combinator,» and the name «DC-S» stands for «Dual Combinator.» This versatile mixer can function as a dual-channel, mixing up to 4 inputs into a single output, or as a single-channel, allowing up to 7 inputs to be mixed into a single output.We put time and effort into the design of DC-S because we think that it is an essential module in any Eurorack system. It offers a ratio size, functionality, simplicity that no other mixer offers.DC-s may seem like a simple utility module, but make no mistake, small things done well can make a big difference.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
DUAL MULTI is a dual buffered multiples.It can be configured as 1 input 6 outputs 1:6 or 2 inputs and 3 outputs each 1:3.Input 2 is normaled to input 1, if nothing is plugged into input 2 you will have 6 copies of input 1 else you will have 3 copies of input 1 and 3 copies of input 2.Buffered multiples have advantages over passive multiples. Since passive multiples split the signal, in case of voltage-critical signal such as V/Oct to VCO, the pitch will vary from one output to the other. With buffered multiples each output will be a perfect copy of the input. Because buffered multis isolate their outputs from the input, any faults or shorts present at the input will not pass through to a connected module.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Dual Rectifier II is a small yet versatile and essential module for any Eurorack system. It can be used as an AC to DC converter, a distorsion, a complex waveform generator, a frequency doubler, a clock doubler or an envelope follower and more.Like all our modules, Dual Rectifier II is built with high-quality components only and designed to offer the best performance.Whether you're starting a small system or have a wall full of modules, Dual Rectifier II is a must-have for any Eurorack system.DUAL RECTIFIER II is divided into two sections:On top section the Positive Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 1.-Output 2 Half-rectified, signal from input 1 below 0V will be remove.-Output 3 Full-rectified, signal from input 1 below 0V will be rectified.On bottom section the Negative Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 2.-Output 2 Half-rectified, signal from input 2 above 0V will be remove.-Output 3 Full-rectified, signal from input 2 above 0V will be rectified.By default input 2 is normaled to output 1 (inverted) of the top section.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Dual Rectifier II - S is a small yet versatile and essential module for any Eurorack system. It can be used as an AC to DC converter, a distorsion, a complex waveform generator, a frequency doubler, a clock doubler or an envelope follower and more.Like all our modules, Dual Rectifier II is built with high-quality components only and designed to offer the best performance.Whether you're starting a small system or have a wall full of modules, Dual Rectifier II - S is a must-have for any Eurorack system.DUAL RECTIFIER II - S is divided into two sections:On top section the Positive Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 1.-Output 2 Half-rectified, signal from input 1 below 0V will be remove.-Output 3 Full-rectified, signal from input 1 below 0V will be rectified.On bottom section the Negative Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 2.-Output 2 Half-rectified, signal from input 2 above 0V will be remove.-Output 3 Full-rectified, signal from input 2 above 0V will be rectified.By default input 2 is normaled to output 1 (inverted) of the top section.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The Eclipse is an analog stereo morphing oscillator that combines the sound character of classic analog oscillators with modern features for advanced sound design.At the heart of Eclipse is a high-precision analog triangle oscillator that tracks accurately over ten octaves. The module provides the full set of inputs and outputs you’d expect from a high-quality VCO, ensuring reliable integration into any Eurorack system.A central feature of Eclipse is its custom waveshaper, inspired by the EMS VCS3. Instead of a conventional wavefolder, this circuit generates rich and complex harmonics with wide-ranging sonic possibilities and dynamic control.The waveshaper concept is expanded into the stereo domain. The result is a dedicated stereo section that allows waveforms to move and spread across the stereo field while maintaining balance, adding a strong spatial dimension to synthesis.Eclipse offers full CV control for all parameters, with smart normalization that enables global modulation from a single source. Additional functions such as XFM, ULFO, Stereo Pulse Array Modulation, Stereo Pulsed Saw Modulation, and RM/AM modes extend the module’s capabilities far beyond those of a conventional VCO.Features:• Analog Stereo Morphing Oscillator• 100% Analog Module• Single high-precision triangle core VCO• 10-octave tracking range with high temperature stability• Morphing waveshaper with 3 modes original circuit design• 2 stereo modes : SPAM Stereo Pulse Array Modulation, SPSM Stereo Pulsed Saw Modulation• 1 quadrature mode : MorphX can be used for wave blending and RM/AM, sidechain ducking• LFO and ULFO modes cycles up to 1h• 3 FM modes: linear, exponential, and custom Xtreme mode• Index input for dynamic FM• Voltage control of both waveshaping and CV depth• Extra square wave based on the waveshaper’s output• Individual outputs: Sine, Triangle, Saw, Square, Sub, Morph-Square• Balanced image with voltage-controlled stereo spread• CV over all parameters• Global modulation hub normalizationDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
As its name implies, EG LFO is composed of an Envelope Generator and an LFO.The envelope generator offers control over Rise, Hold and Fall time. Two ranges of envelopes are available: slow and fast. You can also modify the speed off the fast mode using the speed expander on the back of the module.At the output you will find the envelope output and an inverted copy of the envelope.EG LFO II also features a LFO mode, the speed can be controlled by using the rise and fall control. Two speed modes are available, LFO range in slow mode and audio range in fast mode. You can modify the speed off the fast mode using the speed expander on the back of the module.At the output you will find the LFO output and an inverted copy of the LFO.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.