DIY Kits
available
Another addition to our ADDAC300’s Expressive Controls series. This module converts the incoming light hitting an external light sensor into 2 Bipolar CV Streams:Output: More light > Higher CV outputInverted Output: More light > Lower CV outputThe external sensor is enclosed in a jack socket in order to be used with any standard jack cable and be able to place it in any place outside the Eurorack frame.There are several controls to adjust the CV Output’s signals:• Sensitivity: Adjusts the Light Sensor sensitivity to Light. The Higher the sensitivity the better it responds to low light situations.• Response: 3 fixed settings (medium/fast/slow) to set the slew applied to the raw signal coming from the sensor.• Gain: Sets the gain for both outputs• Offset: Adjusts the Offset for the main Output.• Inverted Offset: Adjusts the Offset for the Inverted Output.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
ADDAC309 CV to Expression allows a simple and straight forward connection between modular and effect pedals that features expression pedal TRS inputs.Instead of using an expression pedal into the effects pedal the user can use this module in between a CV source and the effects pedal to be controlled. This is a great way to control the available parameters on the effects pedals straight from a CV source.ADDAC309 features 2 channels each with a CV input with attenuator and a 1/4" jack output.This is a passive module, the power needed for operation is taken from the pedal power instead of the modular frame, this allows for perfect matching of the pedal’s operating voltage which can range from 3,3 V to 9 V.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
ADDAC312 is a compact battery-powered foot pedal for hands-free gate control. Pressing the pedal sends a +5 V gate from its 3.5 mm output; releasing it returns the output to 0 V. An internal debounce circuit keeps switching clean, and the wooden enclosure is made from birch plywood with a walnut veneer.Features:• Momentary foot-operated gate controller• +5 V while pressed and 0 V while released• Debounced 3.5 mm gate output• Powered by one 9 V battery (not included)• Laser-cut birch plywood enclosure with walnut veneerDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
available
ADDAC313 expands the ADDAC gate-pedal concept to three independent foot switches. Each debounced 3.5 mm output delivers +5 V while its pedal is pressed and returns to 0 V when released, making hands-free control of three modular destinations straightforward. The unit runs from a single 9 V battery.Features:• Three independent momentary gate pedals• Three debounced 3.5 mm gate outputs• +5 V while pressed and 0 V while released• Powered by one 9 V battery (not included)• Laser-cut birch plywood enclosure with walnut veneerDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
only 1 left
ADDAC508 Swell Physics is a four-channel algorithmic modulation source inspired by Gerstner's model of ocean-wave motion. Swell Size, Agitation, Spread and Simulation Speed shape four related 16-bit CV outputs, which can operate as bipolar ±5 V or positive 0–10 V signals. Additional average and gate outputs turn the evolving simulation into a flexible modulation hub.Features:• Four related 16-bit CV outputs based on ocean-wave physics• Swell Size, Agitation, Spread and Simulation Speed controls• Bipolar ±5 V or positive 0–10 V output ranges• Scrolling and evolving simulation modes• Average output plus two gate outputs• Selectable fold, thru and limit clipping behaviourDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
available
While developing our ADDAC105 4 Voice Cluster module we made a new multimode filter to place after the summing mix stage. We were so pleased with its sound that decided to release it as a dedicated filter.To make it more interesting we duplicated its circuitry to be able to use it in a stereo signal path.To make it more versatile we added a switch to set the working mode from Stereo to Dual Mono where both filters can be used independently.In Stereo Mode the Left Cutoff is used to control the Right Cutoff.In this case the Right Cutoff Knob and CV Input are simply bypassed and will have no impact on the Right Channel operation.This allows immediate sync of both filter frequencies when the Stereo position is engaged.Optionally there’s a jumper in it’s back that, when placed, connects the Right Controls back to the Right CV control allowing the possibility to control the offset of the Right Channel Cutoff.Resonance is independent on both Modes and still has to be set manually to match both channels.Both the Audio and CV inputs are normalled from the Left into the Right channels.As standard plugging any input to the Right channels removes this connection.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The TILT EQ concept was first introduced in the 1970's by Quad Ltd, featured on the company’s model 34 preamplifier. The tilt control tilts the frequency spectrum of the audio signal by simultaneously boosting the treble and cutting the bass frequencies, or vice versa, making it a simple to use but powerful EQ.As stated by Quad Ltd, it was designed to produce a very gradual change in balance across the musical spectrum without changing the overall subjective level. This gradual fall from Bass to Treble, or vice versa, means there’s no sudden change and hence no ‘coloration’ added to the sound, the sound will remain entirely natural but with a slight added bottom or high end. In practice, it rotates most of the audio-range frequency response around a 1kHz axis, so as to change the overall balance of the sound from warm to cool without affecting either the apparent volume or the "color" of the sound.Here we introduce this idea into the modular world in a stereo configuration. CV input with attenuverter was added for the Tilt control as well as a Spectral Motion switch that allows stereo spectral matching or inverted spectrum use of the Tilt control: Left = Right matches both channels direction, i.e. when left channel is tilted to the low end the right channel will also be tilted to the low end. Left ≠ Right inverts the Right channel spectrum, i.e. when left channel is tilted to the low end the right channel will be inversally tilted to the high end, or vice-versa. This possibility is extremely interesting when applied as a stereo effect, in other words, a spectral EQ panner.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
This is our new VCO; we discontinued our ADDAC701 VCO a few years back and since then we’ve been wanting to release a more stable version with better pitch tracking, increasing pitch reliability, and further minimizing the detuning issues of analog VCO’s.For this new revision we chose to use the modern version of the CEM3340 ic from CoolAudio and add the triangle to sine circuitry of our previous VCO. This new version is extremely stable over 7 octaves.We also added a new Mix section which allows mixing of all waveforms controlled by 3 knobs SIN/TRI, MIX and SAW/RECT.Features:• Frequency knob with 6 octave range• Fine Tune knob with 12 semitone range• Octave switch with 6 octave range• 1v/octave cv input• Linear FM cv input with attenuator• LFO/VCO switch sets overall frequency range• Soft/Off/Hard Sync switch• Pulse Width control with initial knob and cv input with attenuator• SINE, TRIANGLE, SAW and PULSE outputs• Mix output controlled by 3 knobs SIN/TRI, MIX and SAW/RECT.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
available
Here's the second module of our 700's Heritage Series.Inspired by Moog CP3 mixer, this is a totally discrete analog mixer and it's not, by any means, your standard breakfast mixer, although it can behave like one.This is a wolf in sheep's clothing. Despite its harmless looks there's a dark snarly soul behind that panel that wants to take your sounds into a realm of gritty, gnarly growls.Features:• 4 Independent channels with input jack and volume knob• 1 Feedback/gate knob• Master output volume knob• 6 Front panel trimmers allows user to adjust the Input resistor trimmer for each channel, feedback and master output• 1 Front panel trimmer allows to adjust the mix BiasDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
only 2 left
Here's our new filter inspired by the original WASP Filter.Features:• Four diferent filter types: Low-Pass, Band-Pass, Notch-Pass and High-Pass with independent audio outputs.• Cutoff features a voltage-controlled cv input with a dedicated cv attenuator pot.• Two switches selects different Resonance clipping paths: no clipping / diodes and Resonance depth: high / low.• The Main output filter type can be selected through a 4 position switch.• The Main output circuit features a Distortion/Fuzz circuit that adds extra harmonics to the filtered audio.• Phase switch selects the Main output phase polarity.• One Led monitors the audio signal of the main output.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
only 2 left
ADDAC710 is a dual channel Isolated DI box and is all about keeping the sound coming from your Modular free from any undesired noisy interferences, making sure that what you’re getting from your outputs is what your Modular is actually producing. It provides galvanic electrical isolation between the Modular system and external sources preventing impedance mismatch and ground loop induced hum.ADDAC’s 710 circuit is designed around a unity 1:1 type Audio Transformer operating in the 20 Hz to 20 KHz range, this impedance matching transformer provides two fully balanced outputs (via XLR connectors).ADDAC710 is an alternative to our ADDAC800X High-End Outputs module, we redesigned the original circuit using a smaller transformer that also reduced it’s depth allowing it to fit shallow Eurorack cases.The LIFT/FLOAT/GND 3-way switch lets you choose between lift, ground or floating ground.In the LIFT position (left) the module circuit will be “lifted” to ground through a 100R resistor and a 10nF capacitor.In the FLOAT position (middle) Ground will not be shared leaving ins and outs grounds completely apart from each other fully isolating both signals.in the GND position (right) Ground will be shared between inputs and outputs, here no isolation is used.Any of these three positions may be the best form of avoiding ground loops or any other undesired interference occurring between your modular and the sound system you’re plugging it into.Try out which one of these options will work best in any given situation.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
available
ADDAC711 is a dual channel Isolated DI box and is all about keeping the sound coming into your Modular free from any undesired noisy interferences, making sure that what you’re getting from your inputs is what your external hardware is actually producing. It provides galvanic electrical isolation between the Modular system and external sources preventing impedance mismatch and ground loop induced hum.ADDAC’s 711 circuit is designed around a unity 1:1 type Audio Transformer operating in the 20 Hz to 20 kHz range, this impedance matching transformer provides two fully balanced outputs (via XLR connectors).The LIFT/FLOAT/GND 3-way switch lets you choose between lift, ground or floating ground.In the LIFT position (left) the module circuit will be “lifted” to ground through a 100R resistor and a 10nF capacitor.In the FLOAT position (middle) Ground will not be shared leaving ins and outs grounds completely apart from each other fully isolating both signals.in the GND position (right) Ground will be shared between inputs and outputs, here no isolation is used.Any of these three positions may be the best form of avoiding ground loops or any other undesired interference occurring between your modular and the external hard- ware. Try out which one of these options will work best in any given situation.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
ADDAC712 is a dual channel discrete gain staging amplifier, based on a famous discrete preamp board from the 70’s used in some legendary equipment. What caught our attention was the character of it’s clipping and resulting saturation/distortion.The module can be used with modular signals to add a distortion/fuzz character or as a preamp for an external source such as a line source, keyboard, guitar... It’s also a great side companion for our ADDAC711 Balanced Inputs.At the top an On/Off [BYPASS] switch routes the signal into the Effect (Up: Active) or to the bottom output gain stage (Down: Bypassed).The amount of amplification is set by the [GAIN] control, the maximum amount of amplification can be set by the user using the [MAX GAIN] trimmer.Up to ±5,5v the incoming signal will keep it’s integrity, beyond this point saturation will start to increase. At approx. ±6v a hard clipping will start to occur, this clipping also has a particular quality that at extreme levels it drifts the audio 0v bias reference, moving it upwards which results are similar to a Gate effect.In the middle, an x2 op-amp based output gain stage with a clipping LED, which monitors the clipping at the output, and an [OUTPUT] control to set the output volume.Having the top and middle gain stages provides flexibility allowing the user to completely distort the signal on the top stage and tame it’s output level with the second stage.At the bottom, input and output for both channels (left input is normalled into right input).DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
ADDAC713 is the stereo version of our 703 Discrete Mixer. Inspired by Moog’s CP3 mixer, this is a fully discrete analog mixer and it's not, by any means, your standard breakfast mixer, although it can behave like one.This is a wolf in sheep's clothing. Despite its harmless looks there's a dark snarly soul behind that panel that wants to take your sounds into a realm of gritty gnarly growls.This new version was initially thought of as a percussion mixer, with mono inputs and panning, to allow placing percussive voices in the stereo field, while keeping channel 4 in mono for low end sources like a kick drum or Bass. In the development process we slightly changed this initial idea, adding stereo inputs for the first 3 channels, but still kept the 4th channel in mono.All four [GAIN] controls go to extreme levels, the first 3 channels also feature [PAN] controls.Feedback is used to overdrive the whole mix. As the control is turned clockwise the sound will be clipped harder until it goes completely off, this happens as feedback is increased the audio bias reference also moves up, at extreme levels it offsets the whole signal upwards until it completely goes above the top rail clipping the whole signal hence the resulting gate effect.The [MASTER OUTPUT] sets the overall output gain of the mixer, the two LEDs monitor the audio output signal.The soft clipping switch engages an anti-click circuit which adds a low pass before the output, the switch allows 3 states: Soft low pass / Off / Hard low passFeatures:• Three channels with stereo inputs, gain and pan knob• One channel with mono input and gain knob• Feedback/gate knob• Master output volume knob• Soft clipping switchDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
ADDAC714 is a dual channel soft clipping module.Diode based passive clipping acts as a “brick wall” limiter with a fixed knee given by the inherent diode physics. A passive RC low pass circuit adds a 3,3KHz -3db low pass filter which sculpts the overall tone while also adding further character to the effect.At the top an On/Off [BYPASS] switch routes the signal into the Effect (Up: Active) or to the bottom output gain stage (Down: Bypassed).The amount of clipping is set by the [GAIN] control, it mostly works as a threshold control for how much clipping will be applied. As more clipping is applied the signal’s amplitude will also decrease, to compensate for this we set up a gain compensation stage to keep the output amplitude balanced across the Gain range.Symmetry chooses between bipolar clipping or positive clipping, this relates to the harmonics generated, bipolar for odd and even harmonics (up position) and unipolar for odd harmonics only (down position).At the second stage, an op-amp based x2 output gain with a clipping led, which monitors the clipping at the output, and an [Output] control to set the output volume.Having the top and middle gain stages provides flexibility allowing the user to completely distort the signal on the top stage and tame it’s output level with the second stage.At the bottom, Input jacks for both channels (Left input is normalled into Right input) and output jacksDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Inspired by our ADDAC701 VCO waveform mixing section, our new VC Signal Router also updates our legacy X-Fade/Panner to a stereo configuration that also allows 4 quadrant mixing.Featuring two dedicated X-faders and a stereo VCA that can also be used as a third X-Fader. All controls have their own CV inputs and dedicated Attenuverters for precision control.4 quadrant mixing is achieved by using the stereo Master as a X-fader between left and right channels, this way you can plug 4 audio sources and sweep/crossfade between each and any of them using the 3 x-faders. Plug any 4 sources (4 waveforms of a VCO, 4 LFOs, 4 envelopes...) and sweep through morph through or have them all mixed together.For other configuration types Left and Right X-fader channels can be routed through the Master stereo VCA or sent directly to the outputs. A stereo Direct input can also be routed through the Master VCA or sent straight to the outputs.The Mono Sum output always mix Left and Right outputs together allowing the possibility to use the module as a peculiar 6 channel mono mixer.It can be used for both Audio or CV Signals.Features:• 6 mono inputs• 2 dedicated X-faders with Control knob + CV Input and Attenuverter Each X-fader can be routed through the Master mix or straight into the outputs.• Master channel can be used as a stereo VCA or an X-fader• Stereo direct inputs can be routed through the Master mix or straight into the outputs.• Fully analog audio path with high quality/low noise VCAs.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
only 2 left
Here's our Phono Pre Amplifier module, connect your turntable to it and bring its sound straight into any of your patches.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
available
ADDAC813 is a straight forward stereo mixer. Featuring 5 stereo channels, 4 of them with attenuators, a mono send/return path for parallel processing plus stereo and mono outputs.Four channels with stereo input and gain knob. Fifth channel with stereo input without gain knob, which are the prefered inputs to cascade several ADDAC813s when more channels are needed. Master Output controls the level of the Inputs mix. Two leds monitor the inputs mix.Mono Send / Return return path allows for easy integration of mono effects in a stereo chain. Plug your favorite module through it (filter, bbd delay, spring reverb...) or any mono pedal.The Return Gain works in parallel with the Master Output, just like regular wet / dry controls.The send output can be configured to be line or synth level via a jumper in the back.Stereo output sums the Inputs Mix with the Return signal.The Mono output is the sum of Left and Right outputsEffect PedalsUsing the send output at Line level, the user can connect the send output directly into mono effect pedals and have the pedals output connected directly into the return input without the need of an attenuator/amplifier module.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
ADDAC814A is the 8 HP jack section of the ADDAC814 stereo matrix mixer. It provides six stereo input pairs and six stereo output pairs, with left inputs normalled to right so mono sources can be patched with one cable. The panel connects internally to ADDAC814B and can also be used when expanding a larger ADDAC814 matrix.Features:• Jack section for the ADDAC814 stereo matrix mixer• Six stereo input pairs and six stereo output pairs• Left inputs normalled to right for mono operation• DC-coupled signal path for audio and CV• Internal connection to ADDAC814B or an expanded ADDAC814 system• Compact 8 HP panelDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
available
ADDAC814 is a 6x6 stereo matrix mixer built from the ADDAC814A jack panel and ADDAC814B control panel. Thirty-six level controls route any of six stereo inputs to any of six stereo outputs. The DC-coupled signal path handles audio and CV, left inputs are normalled to right for mono sources, and internal jumpers adapt each input and output between synthesizer and line levels.Features:• Complete 6x6 stereo matrix: ADDAC814A jacks plus ADDAC814B controls• Thirty-six independent crosspoint level controls• Six stereo inputs and six stereo outputs• Left-to-right input normalling for mono signals• DC-coupled for audio and control voltages• Per-channel synth / line-level configuration via jumpers• Colour-coded knobs and expandable matrix architectureDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.