DIY Kits
only 2 left
The AI026 Eurorack Line Interface converts between +/- 2V line signals and +/- 5V Eurorack signals. This allows for the best headroom and highest quality when processing line signals with Eurorack modules, and vice versa.Features:• Stereo i/o• Left inputs are normalled to the right when no jack is inserted to the Right Input.• Volume control for Eurorack to line level signal conversion.• Volume control for line to Eurorack level signal conversion, with the ability to add gain/overdrive for non normalized signals.• Input and output jacksDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The AI002 DIY Mixer Kit is an updated take on a classic utility audio or cv mixer. All three inputs have a level control, with full clockwise allowing full volume prior to the summing mixer. Perfect for adding audio inputs to a filter, or cv inputs to a cv input, and other mixing functions. This kit is ideal for those who know how to solder, but are still starting out in their DIY Synthesis journey.This diy mixer kit will not only familiarize yourself with IC Chips, Capacitors, and Resistors, it will also add a key utility module to your DIY Modular Synthesizer.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The AI008 Matrix Mixer is an active, four in, three out matrix mixer with a summed output. The AI008 can be used to route any of the inputs to any of the outputs. This allows for the creation of feedback patches and other interesting routing, in addition to powerful "regular" signal routing. Common uses include mixing effects outputs into their inputs in order to create drones (or just good old fashioned feedback), mixing oscillators into their own PWM or FM inputs, modulating voltage controlled LFOs and other modulators into themselves, and other feedback patches. The AI008 Matrix mixes is a powerful way to expand any system!DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The AI002 DIY Mixer Kit is an updated take on a classic utility audio or cv mixer. All three inputs have a level control, with full clockwise allowing full volume prior to the summing mixer. Perfect for adding audio inputs to a filter, or cv inputs to a cv input, and other mixing functions. This kit is ideal for those who know how to solder, but are still starting out in their DIY Synthesis journey.This diy mixer kit will not only familiarize yourself with IC Chips, Capacitors, and Resistors, it will also add a key utility module to your DIY Modular Synthesizer.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The AI001 Multiple Eurorack Synthesizer Module is a 1x6 or a 2x3 passive multiple in only 2hp! It is critically important to be able to split and distribute your modular's signals to multiple destinations with the AI001 Multiple Eurorack Synthesizer Module. Because the module takes up only 2HP, they can be placed anywhere.The Multiple Eurorack Synthesizer Module can be used as either a 2x3 passive multiple, or a 1x6. The first set of four are linked together, and if nothing is plugged into the 5th jack, then that signal continues to the 6th, 7th, and 8th as well. If a cable is plugged into the 5th jack, then those signals are distributed to the 6th, 7th, and 8th jacks and it functions as a 2x4 multiple.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
A Loving Tribute to the MS 20 Filter.This OTA Voltage Controlled Filter uses the same filter structure as the venerable Korg MS 20 Filter. The filter is switchable between Lowpass and Hi Pass modes, and features an updated diode gain stage in the resonance section. This circuit was adapted by Sagittronics, who does excellent work.The VCF will overdrive and distort in both the HP and LP modes, and the resonance can self-oscillation. As with the MS 20 Filter, the Low Pass slope is 12dB/octave and the High Pass slope is 6dB/octave. The CV input is an attenuverter, allowing for dynamic control-voltage of the cutoff.All jacks, knobs, and other components are soldered directly to the PCB. There is no wiring, making this kit ideal for those who have built a simple module before, and are looking for a high quality, legendary filter in an easy to build package.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
The AI007 Eurroack Quad VCA Mixer is a compact, high quality, and flexible way to control voltage (audio or CV) in your modular system). Each of the four inputs are DC coupled, allowing the amplitude of CV signals as well as audio rate signals to be voltage controlled. The outputs are also normalled together into a mixer, allowing the AI007 Eurorack Quad VCA Mixer to be used as a voltage controlled mixer. Once a cable is patched into a VCA output that output is removed from the mixer signal, allowing each channel to be used independently, giving users four VCAs in total. A dedicated knob shapes the curve response from Linear to Exponential.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The AI018 Eurorack Stereo Matrix Mixer is a compact 8-in, 8-out matrix mixer. A matrix mixer is used to route audio or cv signals from multiple sources to different destinations. There are sixteen potentiometers, with each potentiometer controlling the amount a given stereo input pair (1-4) will be sent to a given stereo output (A-D).A common usage for the AI018 would be as an effects send, with one or more inputs, and one or more effect inputs and outputs. Using the AI018 Stereo Matrix Mixer in this way, inputs can be sent to multiple effects, and the effects can be sent to each other, and even back into themselves, expanding the depth of the effects.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The AI006 Eurorack Stomp box Adapter is an updated take on a classic utility circuit that converts the higher signal levels of a modular system to be converted to the lower level signals that most stomp boxes are designed for.The AI006 stomp box adapter solves two problems. From the Synth input to the "FX"out, the signal is reduced by a factor of 20 to match the signal levels expected by most stomp boxes. From the "FX" input to the Output, the signal is increased by a factor of 20. Passive attenuators are present on both the send and return in case the input or output levels are too great.Features:• Level conversion: Takes Eurorack signals to guitar level signals suitable for guitar pedals.• Low noise: Maintains a clean and clear signal path, preserving the integrity of your sound.• Compact design: Fits conveniently into any Eurorack case with only 2HP required.• Easy to use: Requires no calibration or special settings, simply patch your Eurorack signals in and your pedal out.• Expand your sonic palette: Use guitar pedals to add distortion, overdrive, fuzz, delay, reverb, and other effects to your modular sounds.• Process modular sounds in new ways: Explore the creative potential of feedback loops, modulation, and other techniques using guitar pedals.• Create unique and experimental soundscapes: Combine the power of modular synthesis with the diverse range of effects available in the guitar world.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The AI010 Eurorack Attenuator is a 2 HP dual passive attenuator with switched jacks that allow the attenuator to also work as a multuple. The top-most input is normalled to the second attenuator knob and the third attenuator input. Control voltage is a wonderful way to add expression to a modular patch, and controlling that control voltage is crucial to being able to dial in that expression.A passive eurorack attenuator is a simple un-powered circuit using only resistive elements (usually a potentiometer) to reduce voltage. Rotating the potentiometer will change the output from 0V to 100% of the input without distorting the shape of the incoming voltage. These are simple and primitive, but effective and important methods of controlling voltage, be it the input to a Filter, or the Linear Frequency Modulation input on an Oscillator.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
The AI106 West Coast Mixer is a fully discrete mixer design that updates vintage West Coast synthesizer mixer designs into a modern form.The AI106 West Coast Mixer takes inspiration from vintage mixer circuits from 60s and 70s West Coast synthesizers, but updates it for eurorack and allows for user customization of the circuit. True to original circuits, the output is inverted. Audio rate signals will sound about the same, but cv signals will be inverted.Because "West Coast" Synthesis focused more on waveshaping and Complex VCO structures as opposed to Subrtacting frequencies from simple waveforms (East Coast), mixers are an important part of traditional West Coast synthesis techniques.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The AI024 X Filter brings the clean, classic, creamy filtering of classic 80s synths to Eurorack. It uses the same four pole analog low pass filter topology found in classic synths like the Crumar Spirit, the Digisound-80 Modular System, Elka Synthex, Fairlight CMI II/IIx, LinnDrum, Oberheim,PPG Wave, Sequential Circuits synths, and many more.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
The AI016 Eurorack Tape Echo Interface is a limited edition module that uses a pre-amp and buffered feedback loops to allow a standard three head tape recorder as an analog tape echo. It also provides op-amp saturation on the input when pushed.The tape recorder must have three heads (erase, record, and play) for it to work as a tape echo. This type of tape recorder will have a button or switch that allows the monitoring of the source audio, or what has just been recorded to the tape. The space between the record and play head creates the delay, and the Tape Interface feeds back into the unit to create repeats.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Reprogrammable Multi-Function Controller based on the Raspberry Pi PicoThe EuroPi is a project aimed at making Eurorack more accessible and customisable by giving users complete control of the inner workings of a digital module.You can plug the module into your computer using a standard micro USB cable, and entirely re-write the program in Python (https://www.python.org) usingany of the inputs and outputs for whatever you want. It can be used to replicate existing concepts, such as a quantiser or sample and hold, or you can write something entirely new.All of the information about this project can be found on the GitHub Repository. This includes the build guide, bill of materials, license details, and firmware.There is also a Subreddit if you'd like to share your builds, ask any questions, or just join the community!Features:• 6 CV Outputs (0-10V)• 1 CV Input (0-10V)• 1 Digital Input (Clock, Gate, Trigger)• 2 Knobs (12 bit)• 2 Push Buttons• 128x32 OLED DisplayDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
This advanced 10HP analog VCO/LFO based on the 3340 IC offers extreme stability, wide frequency range (0.0011 Hz–20 kHz), and eight simultaneous waveforms—including unique PWM Saw and deep Sub Pulse outputs. It supports both exponential and linear FM, three sync types at once, and precise tuning controls. With modes for audio, LFO, and ultra-slow modulation, it’s a powerful all-in-one oscillator designed for creative flexibility and technical precision.Features:• 1V/oct tracking over +10 octaves• Eight simultaneously available waveforms• Unique PWM Saw• Sub Pulse waveform (-1 octave, -2 octave, -2* octave)• Audio / LFO / Ultra LFO modes (up to 15 mins)• Exponential Frequency Modulation• Linear Frequency Modulation• Exp FM and Lin FM simultaneously available• Positive edge Hard Sync• Negative edge Hard Sync• Soft Sync• 3 Sync types simultaneously available• Coarse Knob sweeps 5 octaves in Audio mode• Fine Knob sweeps -+5 semitones in Audio mode• Extremely stable across all temperaturesDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
CanCan delivers studio-quality headphone amplification in a compact 4HP Eurorack module. Powered by high-current parallel op-amps, it drives headphones from 16 to 600 ohms with remarkable clarity, offering exceptional audio fidelity for any impedance.Designed for two independent headphone outputs, CanCan provides separate volume controls for precise monitoring in both solo and collaborative settings. Each channel uses a low-noise Baxandall active volume control, ensuring perfect left-right balance and stereo imaging.With built-in 8-segment LED program meters for peak or average signal monitoring, CanCan is a must-have tool for detailed audio tracking and mixing. Ideal for musicians and producers who demand clarity and precision in every headphone session.Features:• Low Output Impedance (0.5 Ohm): Ensures a high damping factor for precise control and exceptional low-frequency response• Universal Headphone Compatibility: Supports a broad impedance range of 16 to 600 Ohms• Multi-Stage Low Noise Design: Guarantees low distortion and high stability for true-to-source audio reproduction• High Output Current (Up to 140mA): For driving power-intensive headphones up to 600 Ohms with ease• Visual Feedback: Dual 8-segment LED program level meters for monitoring input signal levels• Output Flexibility: One output can be used for driving monitors (using a Y-splitter)• Full-Spectrum Audio Fidelity: Offers a 20Hz to 20kHz bandwidth, perfect for all audio experiences• Protection Features: Includes comprehensive RF and DC input protection with resettable fuses for short-circuit output safetyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The Rabbit Hole 6HP Expander adds two additional input channels to your system, offering enhanced routing options. Each channel can be sent directly to Rabbit Hole or used independently as a standalone VCA. When operating in standalone mode, both channels are normalled to sum at the bottom output for flexible signal processing. Gain CV is also normalled from Rabbit Hole for seamless integration.Features:• Expander for Rabbit Hole• 2 inputs with vintage character OTA VCA• Each channel can be used as a standalone VCA• Attenuverters for CV inputs• All analogue signal pathDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The IOU (Invert Offset Utility) is a powerful 2HP tool for shaping control voltages and audio signals with accuracy. It features an attenuverter and a responsive slider to dial in up to +5V of offset—ideal for fine-tuning signals in both performance and studio settings.A standout function, inspired by DivKid, lets users switch the offset point to either pre or post attenuverter. This enables more refined control when crafting detailed offsets across the full slider range.For added flexibility, IOU includes a selectable gain switch (1x or 2x), allowing for signal boosting or expanding the offset range up to +10V.With both normal and inverted outputs, IOU excels at tasks like voltage scaling, inversion, and generating custom CVs—perfect for techniques such as sidechain-style modulation. A must-have utility for any Eurorack system aiming for precision and creative depth.Features:• Low Output Impedance (0.5 Ohm): Ensures a high damping factor for precise control and outstanding low-frequency performance• Universal Headphone Compatibility: Supports a wide impedance range from 16 to 600 Ohms• Multi-Stage Low Noise Design: Delivers low distortion and high stability for accurate, true-to-source audio reproduction• High Output Current (up to 140 mA): Capable of driving power-hungry headphones up to 600 Ohms with ease• Visual Feedback: Dual 8-segment LED program level meters for monitoring input signal levels• Output Flexibility: One output can be used to drive monitor speakers (using a Y-splitter)• Full-Spectrum Audio Fidelity: Offers a 20 Hz to 20 kHz frequency response for complete audio coverage• Protection Features: Includes comprehensive RF and DC input protection and resettable fuses for short-circuit output safetyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Developed with DivKid, Manic is a compact 8HP dual VCA module built for advanced sound sculpting. It supports mono, dual mono, or true stereo workflows with precision linear VCAs and selectable unipolar or bipolar response—ideal for amplitude shaping or ring modulation.Each channel features a dedicated post-VCA shaping stage:Shape1 delivers TanH soft clipping and classic Serge-style wavefolding.Shape2 adds hard clipping and a Buchla-inspired wavefolder.The asymmetrical design between channels creates rich, animated stereo effects from mono or stereo sources—perfect for depth and width in modular mixes.Optimized for both CV and audio, Manic is a performance-ready tool that brings hands-on control, creative modulation, and stereo imaging into any Eurorack setup.Features:• A collaborative design from both DivKid & Apollo View Modular• Selectable unipolar or bipolar VCA circuitry per channel• Three distinct shape outputs per channel: Inverted, Clipped, and Wavefolding• TanH soft clipping & hard clipping• Serge style wavefolding & Buchla style wavefolding• Stereo operation with perfectly matched gains for the clipping and wavefolding circuits, creating a stunning stereo widening effect• DC-coupled signal path for processing both audio and CV signals• Input and modulation normalisations for simple mono to stereo operation• Flexible signal flow allows for creative combinations, such as ring modulation into clipping or wavefoldingDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Rabbit Hole is a 16HP summing mixer that blends solid-state precision with rich tube character. Featuring two input channels with independent vintage VCAs, it routes signals through a drive stage for solid-state clipping, followed by a starved cathode dual-triode vacuum tube for saturated warmth and harmonic distortion. An optional OWTH diode LED clipping circuit adds aggressive, dynamic edge.Features:• 2 channel mixer with vintage character OTA per input VCAs• 12AU7 Vacuum Tube Core• Fat sounding all analogue signal path• 4 possible stages of distortion• Tone shaping with CV control• Dry/Wet Mix with CV control• Feedback with CV control• Attenuverters on all CV inputs• Switchable diode clipping circuit “OWTH - Off With Their Heads”• “L8” Switch to change Tube characterDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.