Filter
333modules - Rooter

sold out at the moment

Sequential switch, 4 inputs / outputs to one common input / output with pot selector-CV and mute.Features:• Bi-direccional• 4 inputs / outputs• Common input / outputDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€83.30*
ADDAC System - 306 VC Transitions

available

ADDAC306 is a 5 channel multi-directional CV generator.You can think of it as a "sweet spot" controller, or a hands-on way of transiting from one state to another.Each of the five channels has MINIMUM, SPAN and DIRECTION controls, a common CV IN and a common TRANSITION CONTROLLER slider.MINIMUM sets the minimum channel voltage.SPAN sets the voltage range of the channel.It essentially sets the maximum voltage that can be output from the channel, relative to what the current channel MINIMUM is. For a given SPAN value, if the MINIMUM voltage is changed then the maximum voltage output from that channel will also change respectively.DIRECTION sets whether the voltage transition for each channel goes from MINIMUM to maximum, or maximum to MINIMUM.The TRANSITION CONTROLLER slider controls the transition from the minimum value (A) to the maximum value (B) or vice versa, according to the settings of each independent channel.Moving this slider generates 5 different voltages with 5 different ranges and directions. The transition can also be operated from a CV source at the CV IN, in which case the slider position acts as an attenuator for the incoming voltage.The maximum range of each channel can be set to either 5 or 10 volts, by 5 jumpers in the back of the module. Only positive voltages are generated at the output.Using the CV IN you can use two ADDAC306 modules to expand your control options to 9 voltage outputs under one common slider control.Use the VC Transitions to multiply the polyphony of a single CV sequencer by passing its outputs through the ADDAC207.VC Transitions makes for an awesome state transition controller. Plug its outputs to various CV controller parameters of your audio effects modules. Set the slider to position A, and set the minimum values for each channel. Then move the slider to position B and set the SPAN settings for each channel. Use the TRANSITION CONTROLLER slider to morph from state A to state B and backwards. Flip the DIRECTION switches to change the direction of the transition for each channel. Use the CV IN to automate the transition using LFOs, ADSRs or sequencers.Plug the output of your ADSR envelope to the CV IN and set the channels differently to get 5 different ADSRs from one common source.This module's development was based on an initial idea by Konstantine Fioretos.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€113.88*
ADDAC System - 710 Balanced Outputs

available

ADDAC710 is a dual channel Isolated DI box and is all about keeping the sound coming from your Modular free from any undesired noisy interferences, making sure that what you’re getting from your outputs is what your Modular is actually producing. It provides galvanic electrical isolation between the Modular system and external sources preventing impedance mismatch and ground loop induced hum.ADDAC’s 710 circuit is designed around a unity 1:1 type Audio Transformer operating in the 20 Hz to 20 KHz range, this impedance matching transformer provides two fully balanced outputs (via XLR connectors).ADDAC710 is an alternative to our ADDAC800X High-End Outputs module, we redesigned the original circuit using a smaller transformer that also reduced it’s depth allowing it to fit shallow Eurorack cases.The LIFT/FLOAT/GND 3-way switch lets you choose between lift, ground or floating ground.In the LIFT position (left) the module circuit will be “lifted” to ground through a 100R resistor and a 10nF capacitor.In the FLOAT position (middle) Ground will not be shared leaving ins and outs grounds completely apart from each other fully isolating both signals.in the GND position (right) Ground will be shared between inputs and outputs, here no isolation is used.Any of these three positions may be the best form of avoiding ground loops or any other undesired interference occurring between your modular and the sound system you’re plugging it into.Try out which one of these options will work best in any given situation.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€138.04*
ADDAC System - 805 VC Signal Router V2

available

Inspired by our ADDAC701 VCO waveform mixing section, our new VC Signal Router also updates our legacy X-Fade/Panner to a stereo configuration that also allows 4 quadrant mixing.Featuring two dedicated X-faders and a stereo VCA that can also be used as a third X-Fader. All controls have their own CV inputs and dedicated Attenuverters for precision control.4 quadrant mixing is achieved by using the stereo Master as a X-fader between left and right channels, this way you can plug 4 audio sources and sweep/crossfade between each and any of them using the 3 x-faders. Plug any 4 sources (4 waveforms of a VCO, 4 LFOs, 4 envelopes...) and sweep through morph through or have them all mixed together.For other configuration types Left and Right X-fader channels can be routed through the Master stereo VCA or sent directly to the outputs. A stereo Direct input can also be routed through the Master VCA or sent straight to the outputs.The Mono Sum output always mix Left and Right outputs together allowing the possibility to use the module as a peculiar 6 channel mono mixer.It can be used for both Audio or CV Signals.Features:• 6 mono inputs• 2 dedicated X-faders with Control knob + CV Input and Attenuverter Each X-fader can be routed through the Master mix or straight into the outputs.• Master channel can be used as a stereo VCA or an X-fader• Stereo direct inputs can be routed through the Master mix or straight into the outputs.• Fully analog audio path with high quality/low noise VCAs.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€168.98*
Befaco - Hexpander

only 2 left

Hexpander adds great functionality to Hexmix module. Featuring Three aux send with stereo returns, individual outputs for each channel, complete PFL system and balanced output.Hexpander is designed to be placed on top of Hexmix. Expanding Eurorack concept to 6U, allows every channel to be aligned as in traditional tabletop mixers.Features:• Three auxiliar sends with stereo returns and individual controls per channel.• Pre and Post Fader/EQ outputs.• Selectable Line/Modular level at return inputs.• Monitor section with PFL per channel.• Individual PostEq output per channel.• Master section with Headphones amp and balanced line outputsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€265.37*
Befaco - Instrument Interface

sold out at the moment

Instrument Interface is an eurorack pre-amp capable to bring any type of audio signal to modular levels thanks to its amplification circuit.The module can drive regular and condenser microphones (+48V Phantom Powered) as well as Instrument and Line signals with a very low distortion ratio.Instrument Interface offers some additional extra functions like a Trig/Gate extractor and Envelope Follower circuits, allowing you to use the character of your audio signal in more creative waysFeatures:• Neutrik combo Input• Phantom Power selector• Input Impedance selector• Separated Audio en Envelope Level controls.• Envelope Follower with attack and decay control• Gate and Trigger Extractor with threshold selector.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€154.70*
Befaco - Mixer

available

A four channel mixer, suitable for audio or control signals. It features regular and inverted outputs as well as an LED level meter.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€59.50*
Befaco - Morphader

available

Morphader is a performative tool designed to make multichannel CV/Audio crossfade easy and comfortable. Fading from one quad CV/audio scene to another. The core of the module has four CV controlled crossfaders, each with their individual control and a master fader to control them all. The module mixes the four crossfades at its fourth output, thanks to a clever normalization scheme. Each of them can be easily removed from the mix by plugging a cable at its own output.Features:• CV Controlled four channel crossfader.• Attenuators per input.• Normalized voltages to every input, allowing cv levels morphing.• Audio CV response switch per channel• Master Fader control with Lag.• Leds per channel for signal level monitoring.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€165.41*
Befaco / Divkid - MUTES

only 1 left

Mutes goes above and beyond basic muting by allowing you to split groups of signals to multiple destinations, making it great for FX dub performing and varied signal routing.Vactrols on the circuit gives to the switching a pleasing decay for both audio and modulation as well a totally click free muting.Three-position switch: MOMENTARY signal pass-through (it springs back to the center when released); OFF (or muted) in the center; and ON to the right.This module is designed in collaboration with Ben Wilson aka Divkid.Features:• LEDs to visualise signals• 3 way momentary – off – on switching• Buffered and cascading normalising of inputs• Black metal panel• Vactrol based mutingDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€94.01*
Befaco / Molten Modular - Motion MTR

available

Motion MTR allow you to mix, attenuate and invert signals while having clear visual feedback of their levels.Each channel can function as:• Audio level control with VU meter• CV attenuator with voltage meter• CV inverter with voltage meterEach input is normalled to 10v, so you can use each of them to generate fixed voltages. Also, the outputs of channels 1 and 2 are summed into Out 3 to be used as a mixer. Patch it wildly to make it work as an attenuverter with offset, as a mixer, a VU meter or a combination of them all!This module is designed in collaboration with Robin Vincent from Molten Modular.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€113.05*
Befaco / Molten Modular - Motion MTR 1U

sold out at the moment

This is the 1U version of the module, for the 3U standard version please check the other product!Motion MTR allow you to mix, attenuate and invert signals while having clear visual feedback of their levels.Each channel can function as:• Audio level control with VU meter• CV attenuator with voltage meter• CV inverter with voltage meterEach input is normalled to 10v, so you can use each of them to generate fixed voltages. Also, the outputs of channels 1, 2 and 3 are summed into Out 4 to be used as a mixPatch it wildly to make it work as an attenuverter with offset, as a mixer, a VU meter or a combination of them all!This module is designed in collaboration with Robin Vincent from Molten Modular.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€121.38*
Dannysound - VU Meters

available

The Dannysound VU Meters is designed to be used with 2 x Dynamics modules. The modules connect internally via 2x3 pin ribbon cables.The meters provide a visual representation of various signals within the Dynamics modules making settings easier.Controls For Each Channel:3 position toggle switch:1. C/E OUT – Monitor compressor/expander output.2. INPUT – Monitor Dynamics input level or external input if it’s used.3. C/E AMT – Monitor Dynamics compression/expansion amount.3 position toggle switch:1. HI SENS – High sensitivity setting, best for monitoring the C/E OUT signal of percussive sounds and drums etc.2. OFF – If you want to turn meters off. Note that this stops the needles moving but the backlights will stay on.3. LO SENS – Low sensitivity setting, best for monitoring the C/E AMT signal or anything that overloads the HI SENS setting.Features:• External input sockets for monitoring external sources.• Switch to select high or low meter sensitivity or off if the clicking needles get annoying!• Monitoring of the compression/expansion amount.• Monitoring of the unprocessed input level.• Monitoring of the compressor/expander output level.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€166.36*
Feedback Modules - smArTT Verter

sold out at the moment

The smArTT Verter is a simple but very effective utility module for scaling the level and polarity of audio and CV signals.Features:• 1 audio/CV input• 1 input level potentiometer• 1 signal polarity switch (+/-)• 1 DC offset potentiometer (+/-5V or +/-10V)• 3 output jacksDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€28.00*
Herzlich Labs - Apnea 3

available

I know what you want: you want to make something go silent, fast.You want nice, tactile clicky goodness. You want half the size, half the price and exactly as much utility - and buddy, you've found it.Introducing the Apnea 3, 3 mutes that'll make your patch go dead quiet in the click of a button. No funky clicks, no weirdness, just a kill switch that kills your incoming CV or audio signal, ready to be revived with another click of the button - and did I mention it's 2hp? Did I mention it's passive and draws no power? Did I mention it's skiff friendly? Did I mention it's really nice and also good?Finally, the unit is designed to be turned either way, for maximum ergonomic pleasure and utility. You can even choose yourself whether pushing the buttons down will mute or unmute. Neat!Also an excellent gift for the unskilled modular musician who insists on not using headphones.Features:• Quick, simple and customizable build.• Very high utility-per-hp factor and no power requirements.• Works well with both CV and audio signals.• Nice tactile buttons without actuation noise bleeding into your signals!DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€39.92*
Herzlich Labs - Omen

available

The Omen is a dual LPG with a bit more than you might be used to. Like you, I once was lost in the world of low pass gates, seeking something more, something bigger and somehow juicier. The inspiration came to me as I was reading a particularly heavy book on passive filters, and I realized it was possible to make far more interesting LPG designs than the standard we've become so accustomed to.In a convergence of old-school LPG design and more modern components, the Omen boasts two -6dB resonant filters, custom built vactrols, built in CV attenuation and no less than three cutoff modes per filter. Filter 1 is soft and light, imparting a gentle, naturally gated touch of filtering on your sound, while Filter 2 is darker and more resonant, and can turn downright growly and distorted when left wide open.Designed to give you as many creative options as possible, the Omen has the unique ability to function as either two discrete LPG, or as one 4-pole resonant LPG. When plugging a signal in to Input 1, and with no signal plugged into Input 2, the output will be present at both Output 1 and Output 2, with Output 2 producing the signal as it passes through both filters. Tweaking both filters independently will generate a wide array of soft and sometimes harsh tones, ranging from Buchla bongos to early synthesis brass and organ sounds. There is much to love here.CV is similarly handled, by plugging in only one CV source, it will act on both channels - this is useful for creating musically similar outputs as well as when using the dual filter operation. However, the dual filter mode greatly benefits from having two CV inputs: use an envelope in CV1 to act as a VCA, and an LFO in CV2 to create tremolo, for instance.Using custom designed, hand built vactrols, care has been taken to mitigate the less desirable aspects of passive LPGs - in most modules, the user can expect zero bleed through on the LPG channels, and signal attenuation is minimal even with the 4-pole filter settings engaged. Of course, many of the natural features of vactrols remain, such as subtle memory effect when engaging the vactrol for long periods.DIY enthusiast? Rejoice! The Omen is available as a fully loaded DIY kit - everything you need to build your very own Omen packed in one place, so you can easily build one in the comfort of your own home. It is not a difficult DIY project, an ambitious beginner or someone with experience from a few easy builds can tackle the Omen in an afternoon. The build is all through-hole aside from three SMD components, which are easily soldered by hand due to their large size.Finally, you receive maximum blinkenlights as LED's on the front panel simulate the action of the vactrols, so you'll always know what's going on under the hood. No collection of fancy LPG's is complete without the Omen - add some analog warmth to your signals, today.Features:• Functions both as two discrete LPGs or as one multi-pole filter LPG• A passive LPG without the characteristic signal bleed or input loss• You read that right: each LPG contains a resonant two-pole filter• Comprehensive build guide, complete with picturesDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€83.06*
Joranalogue - Test 3

available

Test 3 is a purpose-designed tool for measuring voltages and currents in your Eurorack system. This means that just a single circuit board or module can now replace a convoluted test setup with multiple multimeters, custom cables etc.Two push buttons allow you to cycle the value shown on the LED display between three measurements (voltage, current and stored peak current) of the three power rails. The peak currents continually update in the background on all rails, making it ideal for quickly getting maximum current figures.Apart from measuring the current draw of a single module, Test 3 also supports testing power supplies and cables, measuring an entire system (up to 1 A of current on each rail), troubleshooting DIY modules, powering a skiff or breadboard from a larger system...Note: Test 3 is available as a (very easy) do-it-yourself project, requiring some soldering and basic tools. It can be built either as a standalone circuit board with the DIY Kit, or as a Eurorack module with both the DIY Kit and Front Panel Kit. Most dealers bundle both kits together. With just 11 components to solder, this is a perfect synth DIY beginner project!Features:• Measures up to 20 V and 1 A on each Eurorack power rail, including +5 V.• 20 mV resolution voltage measurement, 1 mA resolution current measurement.• Peak current values of all rails are continually updated.• Pre-soldered SMD parts: perfect DIY project for beginners.• Precision-milled 2 mm anodised aluminium front panel with high-resolution, non-erasable graphics (module version).• Bullet-proof design: polarised power headers and MOSFET protection circuit.• Includes 16-to-16-pin Eurorack power ribbon cable.• Premium mounting hardware: black screws, black plastic washers and matching hex key (module version).• High-quality components and assembly; designed and made in Belgium.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€95.20*
Music Thing Modular - Startup

available

Startup is a headphone amp, six-input mixer, tap tempo clock, divider & multiplier in 4hp. It's the perfect way to start a small Eurorack case. Full DIY Kit.Startup is designed to be the best way to start a small Eurorack case, featuring a Mixer, Clock & Headphone Amp. This is a really easy project for DIY newcomers, all the SMD components come pre-soldered and the PCB is programmed and testing prior to shipping. You just need to solder the buttons, jacks and pot. The Music Thing Modular ‘Startup’ is designed to be the best way to help start a small Eurorack case.This 4HP module does three things:1) It’s a 5 channel output mixer, with a spare channel for stereo signals (like a Korg Volca or a phone).2) It’s a nice clean headphone amp with two outputs.3) It’s a useful tap-tempo clock, with a second channel giving divided or multiplied clocks.The best way to understand Startup is with with the Quick Start Manual. (Use button below)DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€90.00*
Robaux - 3PT

sold out at the moment

The Robaux 3PT is a multimode three-channel control voltage generator.The handy knob with the triple ring-shaped voltage indicator makes the module the ideal performance tool.The Tripot has three control voltage channels which can be adjusted with three parameter trimmers.Instead of using the big knob, the device can also be controlled via the CV input.The module offers seven different modes. These include a performance tool, chord generator, random generator, quantizer, sequencer or LFO.Features:• 1 x CV In, unipolar 5V• 3 x CV Out, unipolar 5V• 3 x ring-shaped led display• 1 x push button• 1 x big knob• 9 x trimmersDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€119.00*
New
Sebsongs - Attenuvert x6

available

ATTENUVERT x6 is just what it sounds like - six attenuverters in one module!The module consists of six inputs, six outputs and six knobs. Each attenuverter can handle +/- 12V signals. All attenuverters are DC coupled.ATTENUVERT x6 is a very useful utility module for tuning in modulation amplitudes and polarities, but it can also be used to invert gate signals and attenuate audio signals.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€70.00*
New
Sebsongs - Offset x6

available

OFFSET x6 is the perfect sibling to the ATTENUVERT x6 - six DC offset channels in a slim package!The module consists of six inputs, six outputs and six knobs. Each offset channel can offset AC or DC signals with +/- 5V DC. Without any signal connected to the inputs, the outputs generate adjustable +/- 5V DC voltages, which for instance could be handy for offsetting v/oct inputs on a VCO.OFFSET x6 is a very useful utility module for tuning in DC offsets for modulation. Many digital modules only accept unipolar modulation (only positive voltages), and many modulation sources are bipolar (positive and negative voltages). OFFSET x6 makes it possible to “shift” the +/- 5V signal from an LFO to instead being a 0-10V signal. Use it in conjunction with ATTENUVERT x6 to also shape the amplitude and polarity of your modulation sources.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€71.28*