DIY Kits
available
The Threetom Modular Doppio is a compact stereo amplifier, drive, and soft limiter module. Doppio helps complex and dynamic stereo sounds to find their place in a modular synthesizer context, where signals are hot, and headroom is extremely limited. Doppio does this by implementing a compact, yet flexible, soft-knee limiter. The limiter is specifically designed for eurorack levels and avoids the need for unnecessary make-up gain, resulting in a lower noise floor.Doppio offers three different gain settings (x1, x5, x21), and three different ratios (linear, drive, and limit). In addition to this Doppio has gain and volume knobs for more precise control. Different combinations of these settings cater to applications like saturating complex stereo signals without turning them into mush, end-of-chain limiting, and boosting line level signals to eurorack level, while still retaining enough oomph to also saturate them nicely. Finding the right settings is made easy by DOPPIO’s unique coffee-bean-shaped indicator lights.Even though Doppio’s architecture is stereo, that doesn’t mean it has no uses on mono signals: Either process two mono signals with identical settings, or chain the two channels to form a two-stage high-gain mono drive. Finally, it’s important to note that Doppio is DC-coupled and can also be used to process CV signals.In summary: Doppio is to your signals what a double espresso is to you – it makes you bigger and bolder – and you know you’re hooked when the withdrawal symptoms kick in.Features:• Three different maximum levels of gain: x1 (0dB), x5 (+14dB) and x21 (+26dB)• Three different soft-clipping modes: Drive mode, Off / linear mode and Limit mode• Caffeine knob for fine control over the gain applied to the inputs• Volume control for post-gain attenuation• Coffee-bean-shaped indicator lights make finding the desired settings easy• Reverse power protection• 4-layer PCB design with completely separate of audio supply rails and groundDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
The Threetom Modular “Mixing Flask” is a utility mixer offering mix-bus limiting and a cornucopia of indicator lights integrated behind a unique chemical lab-inspired front panel.I designed Mixing Flask as a solution to my main three gripes with conventional utility mixers:• Mixing too hot is too easy, leading to hard clipping on the mix-bus. And even when there’s an indicator light to warn you when this is happening, there are no features to actively prevent it.• Utility mixers usually only offer unity gain, so when you have a weak input signal (like a MTM Radio Music), you’re out of luck• They’re nauseatingly boringMIXING FLASK provides solutions to these annoyances in the following ways:• I’ve implemented a soft-clipping limiting circuit on the mix-bus (inspired by DOPPIO). The highest setting prevents the mix-bus from hard clipping altogether in favor of warm saturation.• All inputs have a gain of +6dB allowing you to better equalize between volumes while maintaining a hot mix-bus output• The myriad of indicator lights and front-panel graphics make you feel like a mad scientist in your modular chemical lab. I bet you won’t find another utility mixer that makes mixing more exciting than Mixing Flask!Use cases:• Mix oscillator waveforms without the risk of hard-clipping• Mix CV signals while keeping an eye on what’s coming in and going out• Give a gentle boost to weak input signals (e.g. from a sampler module)• Have a utility mixer in your case that’s interesting to look at, and doesn’t bore you to death!Features:• Three different flavors of saturation on the mix output (hard clipping, soft/hard clipping, or soft-limiting)• Three inputs with up to +6dB of gain, and bipolar monitor lights• One mix output with three-stage bipolar monitor lights (signal present, signal nominal, hard-clipping warning)• Backlit chemical-lab-inspired front-panel graphicsDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
The MS-22 is a dual voltage controlled filter, inspired by the classic Korg MS-20 filter, with an innovative modulation matrix and one of the highest function-to-hp ratios in the land of Eurorack. This module was inspired by many pleasant chats with tech journalist Steve O’Hear. Head over here for a full product description and demos.The MS-22 contains two dedicated filter circuits, one low-pass and the other a high-pass. These are configured in series, the low-pass going into the high-pass. This configuration allows for a unique duophonic fighting resonance behaviour (see this demo video). The cutoff frequencies of both filters can be CV’ed. Compared to most bread-and-butter MS-20 clones, the MS-22 is twice the amount of filter condensed down into half the package (4HP).Features:• Dual VCF inspired by the Korg MS-20 OTA filter• Low-pass into high-pass configuration• Innovative modulation matrix allows CV control over all parameters• Cut-off frequencies can be linked, resulting in a band pass filter with controllable bandwidth• Bipolar monitoring LEDs for the LP, HP, resonance and gain CV signals• One of the best functionality-to-size ratios in Eurorack with a width of 4 HP and a depth of 45 mmDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
As someone who is developing Eurorack modules, I always found it tedious to visualize signals coming from the modular synth on my oscilloscope. The reason for this is that there’s really no convenient adapters for this (well, as far as I know at least). Most workarounds to this problem suffer from two problems: a) They’re usually mechanically unstable, and b) most of the times I would need to redistribute the visualized signal to somewhere else, which requires extra cables and a mult. To alleviate these issues I’ve created the the THREETOM Wiretap, a 2-way mult that you can directly mount onto a BNC connector.This is a fully assembled Wiretap adapter, no assembly required, just plug and play!
sold out at the moment
The 3394 Voice is a compact and flexible analog synth voice that packs a full signal chain into one module.VCO, VCF, VCA, envelopes, and noise. Based on the classic 3394 chip, it delivers rich analog tone with selectable square, saw, and triangle waveforms, routed through a juicy 24dB low-pass filter capable of self-resonance and pitch tracking. Two built-in envelopes shape both filter and amplitude, with switchable AD/AR modes for dynamic control. When unpatched, it acts as a constant VCO output, and the mix trimmer allows tonal variation by blending in a square sub, noise, or external signal. Ideal for melodic lines or snappy percussive sounds like kicks, snares, and zaps, the 3394 Voice is both a complete voice and a set of standalone building blocks for your Eurorack system.Features:• VCO with Triangle/Square/Saw waves• Lowpass resonant 24db filter• Square sub oscillator• Analog noise source• Built in VCA and 2 envelopes• Can also be used as separate Filter/VCO/VCA/Noise sourceDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The Automator is a hands-on, 2-channel tempo-synced CV and gate recorder for Eurorack, built around a large, expressive slider and intuitive controls. It captures your movements in real time, turning gestures into looping modulation patterns with precise timing. Requiring an external clock (4ppqn), Automator continuously records while idle and begins playback the moment you hit record, looping up to 4 bars. You can change loop length and tempo post-recording, and each channel—selectable via a button—is color-coded (red for channel 1, green for channel 2). CV is recorded via the slider, while gates are captured using a dedicated button, with high resolution and flexible timing. Whether you're drawing dynamic modulations or tight rhythmic triggers, Automator gives you a powerful and performative way to animate your patches.Features:• Dual-channel CV and Gate recorder with tempo sync• Dedicated Gate button for rhythmic trigger input• Supports loop lengths from ¼ bar to 4 bars• Channel selection button with color indication (Red = Ch1, Green = Ch2)• Real-time recording resolution (CV every 2ms, gates down to 50ms)• High gate density (up to 125 triggers per bar)• Recordings timestamped for accurate playback timing• Decoupled gate and CV recording for flexible pattern creation• Clock input (4 ppqn) with tempo scaling from 30 BPM upwards• Playback length can be changed after recording without losing dataDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The FMP is an 8 HP Eurorack FM synthesizer module built around the classic Yamaha YM2413 chip, known for its distinctive sound in vintage game consoles like the MSX, Atari, and Sega systems. Capable of producing everything from clean tones, deep kicks, and noisy snares to bell-like textures and even polyphonic chords, the FMP offers two modes: Tone mode provides a 2-operator FM voice with self-modulating feedback, while Drum mode exposes the chip’s built-in percussion sounds with adjustable levels and pitch. Seven parameters shape the sound and CV interpolation between two parameter sets enables evolving, expressive patterns. While inherently lo-fi, the FMP embraces this character to deliver dynamic, gritty textures, with settings that can be saved for consistent recall. Its charm lies in the unpredictability, offering a rich playground.Features:• 8 HP FM synth voice based on Yamaha YM2413 chip• Two modes: Tone (2-operator FM synth) & Drum (built-in percussion sounds)• Wide sonic range: kicks, snares, hats, bells, chords, and more• Seven tweakable FM parameters• Save and recall settings on power-up• Characterful lo-fi sound with modulator feedback• Adjustable pitch and mix levels in Drum mode• Inspired by classic game console sound chips (MSX, Sega, Atari)DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
The SDSV+ is a Eurorack drum voice inspired by SyntherJack’s SDSV project and the iconic Simmons SDS5/SDSV drum machine. This enhanced version goes beyond the original by offering expanded sound-shaping capabilities and increased CV control, making it ideal for crafting everything from classic toms, snares, and kicks to hi-hat, crash, and FM-style metallic sounds. If you want to create vintage punch or experimental textures, the SDSV+ delivers dynamic percussion with modular flexibility.Features:• Envelope selection for the VCO and separate Decay pots• Option to use unfiltered noise for click (and the option to turn click off altogether)• Redesigned one of the envelopes to make it independent of input trigger length.• More CV inputs• Noise level controlDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Ar Merc’het Brao combines a pair of resonant −12 dB filters with two overdrive stages in a compact module; its Breton name translates as "The pretty girls." Configurable for stereo or dual-mono operation and crafted with guitarists in mind, each filter features a switchable mode (Low-Pass or High-Pass) and dedicated CV inputs for voltage control of the cutoff. Global cutoff and resonance controls shape both channels together while the overdrives add harmonic grit and saturation, yielding a versatile tone-shaping device that sits comfortably between modular synthesis and guitar-style processing.Features:• 2 X Resonant 12 dB slope Filter (High Pass/Low Pass)• 2 X Classic Overdrives• Filter Cutoff CV inputs• Global controls for Cutoff and Resonance• Stereo and double mono use• Modular and Guitar friendlyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Distresañ is a musical Baxandall shelving EQ engineered for smooth, natural tonal shaping. Its bass and treble shelving controls let you gently boost or cut low and high bands, while a fixed mid control at 1 kHz lets you add or remove body without resorting to narrow, surgical boosts.Designed for broad tonal balance rather than corrective notching, Distresañ imparts hi-fi–style clarity and warmth with minimal artifacts, making it ideal for shaping sounds in mixing, mastering, and live reinforcement where a transparent, musical response is required.Features:• Baxandall shelving topology for smooth, musical bass and treble shaping.• Fixed 1 kHz mid control for adding or removing presence and body.• Designed for tonal balance and overall sound sculpting, not narrow corrective EQ.• Hi-fi–style response: natural-sounding adjustments with minimal artifacts or distortion.• Suitable for mixing, mastering, live sound, and general tone shaping.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The Eread Doubl was designed to split four stereo inputs, each into two mono CV channels. The first splitter yields channels 1 and 5, the second 2 and 6, the third 3 and 7, and the fourth 4 and 8, providing eight mono outputs from the four stereo jacks.The module also functions as a stereo-maker: two mono inputs can be combined into a stereo output via the module’s stereo jack.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Heklev is an analog echo and reverb module driven by classic MN3007 bucket-brigade devices, capable of lush echoes, dense reverbs and chorus/flanger-style modulation. A built-in VCA and CV inputs for delay rate and VCA make it a flexible performance and studio tool: three front-panel pots control delay time, feedback and dry/wet mix, while CV lets you add rhythmic or evolving motion to the echoes.The module provides three outputs (dry, wet/mix and VCA output) and several trim potentiometers for fine tuning: input/output levels, BBD bias, noise cancellation and the usable range of the delay time knob.Features:• Analog MN3007 BBD-based echo with chorus and flanger capability• Built-in VCA with CV control for dynamic level shaping• Front-panel controls for delay time, feedback, and dry/wet mix• CV input for delay-rate modulation• Three outputs: dry, mix (wet), and VCA output• Five onboard trim pots for input/output level, BBD bias, noise cancellation, and delay-range adjustment• Warm, vintage-style tonal character reminiscent of classic tape and BBD units• Compact 14 HP red anodised aluminium panel for robust, rack-friendly installationDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Possible applications of the Jedoniañ include using a Hz/V synth as a CV keyboard for your Eurorack or vice versa – converting voltages from a 1V/oct MIDI/CV interface to the Hz/V scale and so on. The upper section converts from 1V/octave to Hz/V and V-Trig to S-Trig. The lower unit converts from Hz/V to 1V/octave and S-Trig to V-Trig.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
TouellSkouarn’s Kala Goanv is an inductor-based Eurorack filter that delivers an vintage tone somewhere between a phaser-like band-pass, a gnarly wah-wah and crunchy distortion. Simple in layout but rich in behavior, the Kala Goanv responds musically to hands-on tweaks. A dedicated cutoff CV input with an attenuator lets you add dynamic modulation, though the module’s frequency response is highly parametric — change one control and the whole character reshapes.Because Kala Goanv uses inductors, the circuit can pick up hum and stray electromagnetic fields; keep the module away from power transformers and noisy electronics for the cleanest results. The module is a compact, characterful filter that brings organic, wired-in vintage texture to modular patches.Features:• Inductor-based filter topology for a distinctive phaser/wa-wah/distortion character.• Large main cutoff knob with tactile vintage control.• Input and output level controls for level matching.• Highly parameter-dependent frequency behaviour – very responsive to knob adjustments.• Sensitive to hum and electromagnetic fields – avoid close proximity to power transformers.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Skorn da Bask is a expert for creating Drones. Its composed 3 analog Oszillator and a low pass filter. The VCOs can not only be used to generate audio signals, but for modulating the VCF’s cutoff frequency as well.Features:• 3 analog OSCillators/LFOs• 1 analog Low Pass Filter (24dB)• Osc 1, 2, 3 CV Modulation input• Filter Audio Input• Filter Modulation inputDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Sonveskan is a three-channel mixer built from discrete components and germanium transistors, engineered to deliver gritty, analogue warmth and aggressive harmonic colour. Each channel features two serial gain stages (a front-panel drive control plus a PCB trim), voltage-controllable feedback with a dedicated feedback pot and CV input, a mute switch and a direct output. The main channel adds a two-band equaliser and an additional gain stage with its own trim for extra edge and saturation.Patching multiple strips together encourages wild feedback, multi-stage distortion and experimental textures, making Sonveskañ a compact but powerful tool.Features:• Three identical channel strips with dual serial gain stages.• Voltage-controlled feedback per channel with CV input and feedback intensity control.• Mute switches and direct outputs on each channel for flexible routing.• Main channel two-band EQ plus extra gain stage for added grit.• 2017 model fitted with larger coupling capacitors for improved bass response.• Built around germanium transistors and discrete circuitry for vintage, lo-fi character.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Strakal Brulu is a great sounding Germanium Fuzz Module. Very characteristic for the module’s sound if the feedback that is coupled to the feedback. The more fuzz, the more feedback. The Strakal Brulu 2 can get pretty nasty and it screams a lot at high fuzz settings and low input level. The fuzz amount can be voltage controlled, with an inverse attenuator.Features:• 2 NOS Germanium Transistors• Cv controled by vactrol• Classic Fuzz sound for mudular levels• Feedback screamingDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
The two fuzzes share the same controls. The Fuzzes and EQ are slightly differents (great for strereo). You can output the Stereo signal by plugin a stereo cable or you can output a mono signal : Fuzz1 - clock wise or Fuzz2 - counterclock wise, or a mix of the 2 fuzzes by turning the morphing pot.Features:• Selected Silicon transistors• Mono input• Stereo output - with stereo cable• Mono morphing output - with mono cable• Feedback (with cv control)• EQ (low high)• Morphing (with cv control) Clock wise Fuzz1, counter clock wise Fuzz2• Input Volume• Gain• Stupid Breton nameDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Stereo tube headphone amplifier featuring a balanced 6.35 mm jack output. The right input is normalized to the left, enabling monitoring of mono sources without extra routing, while the low-impedance balanced output preserves transient detail and channel separation for headphones.Carefully engineered with high-quality parts in France, the circuit pairs high-performance OPA2134 audio op-amps with NOS OTK Ukrainian tubes. It accepts small-signal tubes such as 6j1P, 5654, 6AK5 and EF95, offering a warm, analogue character with robust build quality and audiophile-grade components.Features:• 12V and 5v compatible (selectable heaters voltage via jumpers)• Tube sound• Compatible with 6j1P, 5654, 6AK5, EF95 tubesDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Strakal Orsel is a tube distortion module that injects organic, vintage character into a modular setup. True to Touell Skouarn tradition, control labels use Breton terminology, while input and output are marked with arrows for clarity.The unit’s topology offers flexible tonal shaping: the Triodenn selector changes the left tube between pentode and triode operation, altering the core sound. The Boukl Retroaktiñ control combines a feedback engage switch with a level pot that ranges from subtle thickening to full, screaming self-oscillation. Gounid sets the balance between the first and second stages. Ampled governs the amount of saturation. A dedicated CV input, Enkas Modulañ, lets external control influence feedback and overall level even when feedback is not engaged.Beyond straightforward distortion, the circuitry produces rich secondary behaviors. With feedback pushed wide the circuit behaves as a powerful effect oscillator whose pitch responds to CV (not calibrated to strict 1 V/oct tracking). With feedback off and conservative level settings, the unit exposes its tube noise floor and can operate as a raw, characterful VCA.Features:• Tube distortion module• Exposes tube noise floor for characterful texture• Can function as a crude VCA• Compatible with 6j1P, 5654, 6AK5 and EF95 tubes• Boutique construction, made in Plougastel-DaoulasDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.