DIY Kits
only 2 left
Κλάσματα is a single channel, voltage controlled Euclidean sequencer.It offers a range of 1-32 steps, opening up more possibilities for complex patterns. With voltage controlled sequence length and fills, Κλάσματα can transpose, shift and modulate rhythmic patterns at up to audio speeds.Just like Stocheia there is a normal and a toggling operating mode. The three-way switch is also used to stop and reset the sequence.The voltage controlled parameters have individual level settings. The controls are otherwise identical to Stocheia.For more infos, please visit the Rebel Tech website.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Λόγοι is a voltage controlled clock divider, counter, and delay. It subdivides and adds time, creating organic, evolving signatures. Λόγοι brings movement and life to the trigger signal, from a subtle swing to bizarrely complex and intricate rhythms. Instructions The functions of Λόγοι are split with division on the left, and addition on the right. The right side operates either in Counter mode, by adding clocks, or Swing mode, by adding a time delay. The mode is set by the centre switch. The module has CV inputs (top jacks) and trigger outputs (middle left/right jacks) for each side, and a combined trigger output (centre bottom jack) which gives the output of both operations: divide and add. The trigger input (bottom left and right jacks) is shared between division and addition. There is also a reset input (middle centre jack) and manual reset switch (push switch up). There are three LEDs indicating the divided and added output to the left and right, and the combined output in the centre. Divide The divider toggles its output every n clocks, where n is the divisor. The divisor is set with a manual (top knob) and CV level control, in a range from 1 to 32. Count With the switch in the down position, the additive side functions as clock counter. The counter will output a trigger signal every m clocks, where m is the addend. The range is from 1 to 32 clocks, with 16 in the centre position. The combined output will divide and count. If i is the incoming clock, n the divisor, and m the addend, then it will output a a trigger signal every i/n + m clocks. Note that when the addend is larger than the divisor, in other words, n < m, then the divider frequency is higher than the addition and the combined output will never trigger. Swing With the switch in the centre position, the right side adds a time delay to the input. The amount of delay, or swing, ranges from 0ms to around 1000ms. In Swing mode, the combined output passes all clocks through until each time the divisor triggers, when it adds a time delay. The result is that every n-th clock is delayed by m, where m is the amount of swing and n is the divisor. As in Count mode, if the divisor frequency is greater than the delay time, the combined output will not trigger. In Swing mode, this is determined by the combination of input clock frequency and delay time. DIY-Kit-Type: THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Φορέω is a triple function processor for triggers, gates and clocks. It simultaneously performs pulse width modulation, multiplication and repetition, with individual input, output and CV for each function.• Pulse width modulation, as a ratio of the input signal rate, is adjustable from 0 to 100 percent. Multiplication also operates on the input signal rate, multiplying it by a factor from 1 to 16.• Repetition generates a burst of triggers, at the rate of the multiplier, with repetitions adjustable from 1 to 16.Each function has two knobs for manual and CV level, and three jacks for trigger input, CV input and trigger output.Pulse width modulation carries through to the outputs of the two other functions, and the three trigger inputs are normalled from top to bottom.When multiply and repeat are combined, Φορέω makes an excellent burst generator, perfect for rolls, flams and fills. The repeater gives precise control over burst length, while the multiplier easily moves from quarter notes, to thirds, to eights, to everything in between and lots more beyond. Go on, give us a snare rush!Φορέω is also extremely versatile with many utility functions, such as master clock doubling, clock modulation, and for triggering and clocking fast sequences. It even works as a square wave overtone generator with PWM, tracking audio input signals up to 20kHz.Φορέω perfectly complements Στοιχεῖα, Λόγοι, Κλάσματα and Χρόνος, completing our Euclidean series of trigger processors.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Στοιχεῖα is a dual Euclidean Sequencer. It algorithmically generates rhythmic sequences from an input trigger signal. The name (Στοιχεῖα, Stoicheia, or Elements) comes from the title of Euclid’s book Elements in which the algorithm was first described.HistoryThis goes way back. In the third century BCE, the Greek mathematician Euclid described a way to determine the largest common denominator of any two integers. As it turns out, his method is the same as what people have used to divide beats into rhythms. Across the globe, from ancient to modern times; the rhythms that pervade human existence can be generated using the same, simple algorithm.The cultural and historical range covered by these rhythms is nothing short of breathtaking. From Brazilian Samba and Bossa-Nova, to Bulgarian folk dances, thirteenth century Persian drum patterns, and complex poly-rhythms of West and Central Africa.Of course, Euclid’s work can be applied to more than just rhythmic patterns. A scientist named Bjorklund applied it to nuclear physics, in order to optimise the operation of the SNS particle accelerator. He also published his work with a proof of the efficiency of his method. Then, in 2005, a Professor of Computer Science called Godfried Toussaint linked up the dots and presented in a research paper the connection between the work of Euclid, Bjorklund, and musical rhythms.We have based our implementation on the work of Toussaint, Bjorklund and Euclid.Getting StartedConnect the left sequence output (second jack from the bottom left) to an envelope gate input controlling a sound source, or something like the trigger input of a drum module.Make sure the middle switch is in the centre position, and the left switch is in the up position. Now connect an LFO to one of the two clock inputs (bottom left or bottom right jack) and you should see the centre LED light up when a signal is received. If the LFO is very fast, the LED will appear to be dimly on - turn the speed down (or up) to where it is flashing at a regular pace.When an input clock signal is received, the centre LED will light up. When a sequence triggers an output gate signal, its corresponding LED will light up.Turn all the knobs in the left column to their centre positions. You should know have a sequence of length 8 with 4 fills (50% of the step length). This means that every other beat will be ‘on’, and you should see the sequencer LED flash on every second input clock. Consequently, the sequence output should generate a gate signal, triggering the module you have connected it to.If you turn the bottom left knob in the anti-clockwise direction, you will hear progressively fewer ‘on’ beats in the sequence until only one in 8 (the sequence length) beats is on. Turning in the clockwise direction, the sequence will start filling in more and more beats, until every beat is on.Now connect a different envelope or sound source to the other sequence and repeat!InstructionsEach sequence is controlled by a column of three knobs and a switch. The input parameters to the algorithm are sequence length and fills.The length of the sequence, measured in clocks or beats, is controlled by the second knob from the top. The range goes from 1 (fully counter clockwise) to 16 (fully clockwise), with 8 in the centre position.The number of fills, or on-beats, is set by the third knob. In fully counter-clockwise position, this is set to 1. Centre position will set every other beat ‘on’, or 50% . Fully clockwise sets every beat ‘on’, in other words: the number of fills are equal to the sequence length.The top knob adjusts which beat the sequence starts on - and hence resets to. In its centre position, the sequence will start on its first step. The start position can be changed by turning the top knob left or right: this will have the effect of rotating the sequence left or right, respectively.Trigger ModeWith its switch in the centre position, the sequence is turned off. To turn it on (Trigger Mode), push the switch up. In trigger mode, the sequence will switch its output high when receiving a clock signal rising edge (low to high transition), provided the next beat in the sequence is ‘on’. When the clock signal falling edge is received (high to low transition), the output will be switched back to low (0v). This means that the output trigger signals have the same pulse width as the input clock. So if the clocks are generated with very short pulses, the output triggers will be equally short. As a consequence, a pulse width modulation on the input clock signal will be passed on through the sequencer.Alternating ModePushing the switch down from its centre (off) position puts the sequence into Alternating Mode. In alternating mode, the output goes high on the first ‘on’ beat, and remains high until the next ‘on’ beat. In other words, the output toggles on every ‘on’ beat in the sequence. The up and down transitions occur on the rising edge of the input clock.ResetThe centre jack can be used to connect a reset trigger. When a reset is received, both sequences restart at their first position. This takes into consideration the rotation setting: If sequence A and B have different rotations, they will remain offset in respect to each other. Reset can also be manually triggered by pushing the centre switch momentarily upwards.Chained ModeThe centre switch can be pushed down, which enables Chained mode. When chained, the two sequences are repeated one after the other, instead of concurrently. This is very useful to build up more complex patterns. In chained mode, the output of the combined sequence is available at both output jacks. On startup, the first sequence will play through to its determined length. It will then stop, and the second sequence will play through to the end, at which point the first one starts up again. For example, setting the first sequence to length 12, and the second to length 4, will result in a combined 16-step sequence. A reset signal in Chained mode brings the combined sequence to the start of the first pattern. Rotation works as in regular mode. Chained mode can also be used to create sequences longer than 16 steps.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The Witch is a compact and versatile polyphonic synthesizer. The Witch can be used Standalone, with a MIDI Controller, Analog Sequencer, or MIDI Polyphonic Expression / MPE Controller. It's USB powered or with 9V DC.It comes with four different synth engines:• SubTract Virtual Analogue synthesizer with 48dB resonant filter• VoSim Voice Simulator formant synthesizer• WaveBank Morphing wavetable synthesizer• QuadSampler Sampler with peak filterEach synthesizer engine is provided in two variants:• Expression Mode Continuous pitch control and MPE support• Performance Mode Discrete pitch control, standalone chords and classic MIDI supportOther features include two assignable tap tempo LFOs with continuously variable shapes and a powerful effects section.As well as eight factory patches, the Witch is fully compatible with the OWL Library of more than 300 patches. What’s more, users can create their own patches using any of the supported DSP languages: Pure data, Max gen~, SOUL, Faust, Maximilian and C++.The Witch has its own Synth Editor web application: witch.rebeltech.orgDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The Robaux 3PT is a multimode three-channel control voltage generator.The handy knob with the triple ring-shaped voltage indicator makes the module the ideal performance tool.The Tripot has three control voltage channels which can be adjusted with three parameter trimmers.Instead of using the big knob, the device can also be controlled via the CV input.The module offers seven different modes. These include a performance tool, chord generator, random generator, quantizer, sequencer or LFO.Features:• 1 x CV In, unipolar 5V• 3 x CV Out, unipolar 5V• 3 x ring-shaped led display• 1 x push button• 1 x big knob• 9 x trimmersDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
The Robaux Decision Tree randomly sends a gate to one of three outputs and then to one of three sub-outputs. Generate unpredictable rhythms. You can choose to route a gate to a single random output or play polyphonic gates. Utilize the knob to transition from total chaos to a repeating loop.The latch mode lets you hold an incoming gate. Pair it with a multimode filter to select various filter types. Use it to alternate between a variety of waveforms. The random input routing injects vibrancy into your sound.The DCSN 3 can also function as a traditional clock divider. The signal is split from half to 1/16 on the top four jacks. Additionally, a continuous sequence is output through the lower eight jacks. Odd divisions enable intricate rhythm creation. Utilize it at audio rate for polyphonic chords using just one square VCO.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Program your patterns like on a classic TR machine. Record patterns with your fingertips. Create random patterns at the touch of a button.Turn your patterns into exciting performances with the mute and fill function.The LL8ᴵᴵ has 16 patterns with up to 16 steps. Create longer rhythms by chaining multiple patterns.But that's not all: The lil eight is now polymetric! Each track can have a different length, length reset, legato and a probability function.For even more exciting performances, there's a new fill mode that repeats entire steps of the whole pattern!Enter the world of modular drums with the Robaux Little Eight II.Features:• Number of Tracks: 8• Number of Steps per Track: up to 16• Number of Patterns: 16 (chainable)• 1 x Clock In• 1 x Reset In• 8 x Trigger Out• 1 x MIDI Out (adapter required)• 20 x backlight silicon button padsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The MIDI Adapter works with LL8, LL8-2 and also works with SWT16+ with MIDI-firmware.With the LL8ᴵᴵ and the above named machines you can use MIDI devices like drum machines or samplers.Each track of the sequencer can output an individual MIDI note to one of 16 MIDI channels.The new Robaux MIDI adapter now has a space-saving mini jack and could be reduced to a width of 2HP. The adapter can be used for both MIDI Type A and MIDI Type B.
available
The Robaux SWT16+ is a 16-track eurorack trigger sequencer with up to 64 steps per track.The Sweet Sixteen Plus is perfect for triggering drums, envelopes or modulation sources.With the new member of the Robaux family, you can switch between eight different patterns.This will allow you to create even more exciting performances. You can store these patterns in up to 16 memory banks.Program your tracks step by step. Play your tracks on the fly. Or just use the new Euclidean rhythm generator.The new design has even more crazy flashing buttons! With the improved menu navigation, you can use the sequencer even more intuitive.The sequencer offers 16 different modes to create and modify rhythms. Modes are divided into four distinct areas:Create, Perform, Track Settings and Sequencer Settings.Randomize your tracks, move your steps or reverse your patterns. With these tools, you can discover entirely new rhythms.And the new Coin function adds even more variety to your beats.Features:• Number of Tracks: 16• Number of Steps per Track: up to 64• Number of Presets: 16• Number of Patterns per Preset: up to 8• 1 x Clock In• 1 x Reset In• 16 x Trigger Out• 1 x MIDI Out (Alternative firmware and adapter required)• 28 x backlight silicon button padsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
All knobs and no menus, an FM synth engine with hands-on controlALGO's four oscillators can be configured in series or parallel combinations, to create Complex FM or additive sound textures.A unique Algorithm Display indicates the signal flow from one oscillator to another - easy to understand FM with pretty twinkly lights!Each oscillator has controls for Level and Frequency, allowing easy adjustment of FM timbres, no menu diving snorkels needed.Modulation inputs for Frequency or Level for each oscillator - patch in a couple of Envelopes, and you have an instant FM synth voice.Bored of Sine waves? A generous Wave Warp control bends things through Triangle to Pulse wave and back again.Wave Warp can be applied to Carrier, Modulator or both types of oscillator.For the more discerning mangler, Wave Folding is also available in three delicious flavours; Symmetric, Asymmetric and Soft Clip!A Global Detune spread control with CV input is great for creating Netflix apocalypse drones that descend into the abyss.Lastly an onboard Stereo Chorus can add a vivacious 1980's shimmer to all your FM creations.Oh, nearly forgot. It's Stereo !Features:• Frequency range 8 Hz - 35 kHz• Sampling frequency 85 kHz @ 2 x oversampled (170 kHz)• Four through zero oscillators• Harmonic intervals, Fine tune, or Fixed frequency options for each oscillator• Amplitude OR Frequency/V/OCT CV inputs for each oscilator• 9 FM algorithm combinations• Wave Shaping and three types of Wave folding• Multi Stage vari-speed high quality chorus effect• Stereo output, with Pan control for each oscillator in the stereo field• Pretty lights !PLEASE NOTE THE KIT IS ONLY SUITABLE FOR EXPERIENCED BUILDERS.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
ENVY MACHINE is a compact modulation powerhouse with four independent channels, each offering a wide range of modulation options. From envelopes and LFOs to random voltages and unique knob recording, ENVY MACHINE delivers remarkable flexibility in a small Eurorack format.Each of the four modulation channels operates in one of five versatile modes:• ADSR Envelope• AD Envelope• AD LFO• Random Voltage Generator• Recordable Knob MovementKnob Recording lets you manually animate parameters, capturing expressive modulations to add life and dynamics to your patches.Each channel includes its own dedicated MOD input, enabling external CV control over parameters such as time, level, waveform shape and more.Both inputs and outputs feature bipolar attenuverters, allowing smooth transitions between unipolar and bipolar signals with precise modulation depth control.Shape your modulation curves with continuously adjustable waveforms that morph seamlessly between LOG, EXPO, SINE, TRAPEZOID, and SQUARE.Technical Specifications:TIME• Envelopes: 1.5 ms – 4 min• LFO: 88 Hz – 7 min cycle• Random: 2 kHz – 2 minOUTPUT VOLTAGE RANGE• Envelopes: 0 V to 8 V (inverted: 8 V to 0 V)• LFO/Random: 0 V to 8 V (Unipolar) or -5 V to +5 V (Bipolar)INPUT VOLTAGE RANGE• -5 V to +5 VFeatures:• 4 modulation channels, each with 5 selectable modes• Knob Recording (“Ghost Hand”) for expressive, animated modulations• Dedicated external CV modulation input per channel• Bipolar attenuverters on all inputs and outputs for flexible polarity control• Smoothly variable waveshapes: LOG, EXPO, SINE, TRAPEZOID, SQUARE• Compact, intuitive Eurorack design – ideal for both performance and studio useDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
The M185 is the most intuitive and playable Eurorack sequencer.It appeals as a hands-on performance orientated module for easy creation of complex melodic sequences.It is the original multi-step-per-stage sequencer that inspired the Metropolis and Metropolix modules.• Features an expansion header for chaining two M185s for 16 stage sequences• Lots more quantisation scales• Live X0X style Gate Pattern programmingOVERVIEW• 8 unique gate modes for creative rhythmic possibilities• A/B split mode for two separate sequences, like having two sequencers in one box• 2 channels of CV/GATE and MIDI I/O• 15 Quantise scales OR pure analogue microtonal CV outputINPUTS & OUTPUTS• 2 channels of CV and Gate outputs• Expansion header to connect two M185s for 16 stage sequences• Reset input [ shared with MIDI input ]• Sync output [ shared with CH2 gate ]• Bidirectional Clock I/O• MIDI input for MIDI clock in, MIDI note transpose• MIDI output for MIDI clock out, MIDI note outputSTAGE DETAILS• 8 stages, each with individual 1-8 step repeats per stage• 8 gate modes per stage [ Off, Once, All, 1/2, 1/3, 1/4, Probability or Programmable, and Long ]• Programmable gate patterns for 'on the fly' X0X style programming of gate triggersEVEN MORE DETAILS !• AB serial split sequence mode with 1-8 sequence repeats for AAABAAAB sequence structures• AB parallel split mode, for two separate simultaneous sequences that play at the same time• Root note offset and reset trigger options from sequence B to A• 2.5V / 5V voltage range selectable• MIDI note output including programmable velocity• MIDI to CV converter mode [wow]• Programmable glide per stage• Easy user upgradable firmware using MIDI sysex filesPLEASE NOTE THE KIT IS ONLY SUITABLE FOR EXPERIENCED BUILDERS.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Four multi model filters with stereo capability, combined with a six-stage four-channel modulation sequencer. Finally a filter bank that unifies the control of multiple parameters, enabling a spaghetti-free approach to formant animation fun.NIGHT RIDER cleverly turns the dials to where you want them, when you want, via it's unique modulation sequencer.PLEASE NOTE THE KIT IS ONLY SUITABLE FOR EXPERIENCED BUILDERS.Create dreamy swooshing 70’s phaser filter sweepsPhenomenal for phoneme vocal formant rasps and wheezesPlucking great for strumming Karplus Strong twangs, and pinging filter pings !Or, turn your silk into shredded cabbage, with the built in bad-ass clipping-saturatorWARNING! To build the kit you MUST have the following:• Two mini clamps• Clean high quality 2/3mm tip solder iron [ chisel type recommended ]• Mini Phillips screwdriver for M3 & M2 pan head screwsThe PCB is double sided, and any mistakes soldering some parts might be very difficult to fix laterThis is a complete kit for Eurorack, Including all parts:1xPCB (All SMD parts come already pre-soldered), a high quality screenprinted 2mm aluminium panel, encoders, knobs, switches, LED displays PCB, jack sockets, and all sundry components. Includes USB data cable for firmware install, sexy black Eurorack power cable, RYK stereo splitter cable.Features:Four filter blocks, with multiple models , including:• 6db BPF [ pingable ]• 12db BPF [ pingable ]• 12db variable width BPF• Comb Filter for Karplus Strom [ pluckable & flanger vibes ]• All Pass filter [ crazy Phaser vibes ]• Dual Input and Stereo output, with Pan control for each filter in the stereo field. Input can be Mono [ CH1 - 1,2,3,4 ] or Dual [ CH1-1,2 CH2 - 3,4 ]• Modulation Sequencer capable of being clocked, scanned, and interpolated• CV inputs for sequencer Interpolated scanning, 1V/Oct frequency offset, Slew amount, Resonance amount, Clock or MIDI clock input for sequence animation, MIDI CC• Memory slots for storing and retrieving Filter and animation setups, and retrieving preset formant, and chord based Filter setupsDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
B77 TAPERecord your Workshop jams onto Tape!Tape is an audio recorder for recording approximately 1.5 minutes of mono sound onto two separate tracks. Playback speed is continuously variable, as is the mix between the two tracks. Audio data is stored on the card and is kept between sessions, so multiple B77 cards can be used to store samples for different songs in a live set etc.355 PITCH TO VOLTAGE / 350 VOCODERWith the 355 Pitch to Voltage – turn your whistling, singing, or (monophonic) guitar into a synth.Pitch to Voltage converts a monophonic audio input to a V/Oct pitch CV, and an envelope follower CV. Also included is a built-in oscillator with five waveforms that tracks the audio input signal.On the same card is the 350 Vocoder – Ever wanted to let your Mr Blue Sky get Intergalactic whilst Watching the Stars with Kelly? Now you can, using this classic 14-band Vocoder, which includes an optional internal 4-note polyphonic carrier synth.910 PITCHED DELAYNeed some “Visconti drums” or “Hassell trumpets” ?The Pitched Delay has a continuously variable range of ±1 octave for creating harmonised pitch shifting to wild cascading pitched delays. Try using no feedback with pitch at 5th down, 3rd or octave down to add a harmonised sound to solo instrument.
available
NO DIY – THIS UNIT IS FULLY ASSEMBLEDTIME SLICE is a Quad-channel Eurorack looper and sampler for realtime time-warping and multi-track performance. Warp the fabric of time with Time Slice, a powerful quad-channel Eurorack audio looper and sampling workstation built for live performance and studio experimentation. Each of the four channels has its own large rolling buffer and dedicated FX chain – including H3000-style pitch-shifters, delay, reverb, tilt filter and wave-fold – plus a dedicated stereo mix output for final routing. Record, resample and overdub tracks, use 1-Shot sampler playback or enter a unique retrospective loop mode that captures what you just played even if you weren’t recording. Internal and USB storage let you load and save WAV files (with embedded WAV markers for multi-sample instruments), while extensive I/O – assignable CV inputs, per-track Trigger IN/OUT, MIDI and clock sync – keeps TIME SLICE tightly integrated with modular rigs and external gear. Inputs accept Line, Eurorack and Hot-Euro levels, and the module can ping-pong audio between tracks or record the stereo mix back into a buffer for creative multi-track manipulation. A bold retro scroll wheel and high-visibility display put hands-on control at your fingertips. TIME SLICE ships with a curated sample/loop library so you can start shaping time immediately.Features:• Quad-channel Eurorack looper/sampler with large rolling buffers per channel.• Dedicated Stereo Mix Output for mastering or resampling the master buss.• H3000-style real-time pitch-shifters on every track for dramatic time and pitch manipulation.• Per-track FX: pitch-shift, delay, reverb, tilt filter, wave-fold and more.• Internal and USB WAV storage with embedded WAV markers for multi-sample instruments.• Assignable CV inputs and per-track Trigger IN/OUT for modular control.• 1-Shot sampler mode, traditional loop mode, and unique retrospective loop mode.• Resampling/ping-pong routing – resample other tracks or record the Stereo Mix as a new track.• MIDI and clock-sync friendly; keeps impeccable timing in complex setups.• Accepts Line, Euro, and Hot-Euro levels for wide source compatibility.• Hands-on UI: large retro scroll wheel and high-visibility display.• Includes a starter library of samples, loops and effects to get you started.
only 2 left
FM & Vector Synthesis - Two icons of the '80s in one unit!Introducing the new Vector Wave from RYK Modular bringing together the awesome power of 16 oscillator FM, combined with Vector synthesis OR true multi voice polyphony.The Vector Wave is a feature packed compact Eurorack module, which can be used as a stand alone synth-voice without the need for external VCA,ENV, LFOs etcWARNING! To build the kit you MUST have the following:• Accurate and stable 5.00V reference source to calibrate the module• Flux pen, or liquid flux• Two mini clamps• Clean high quality 2/3mm tip solder iron [chisel type recommended]Features:• 16 oscillators, divided into 4 banks, oscillators can freely configured into series or parallel combinations for complex FM or additive synthesis• A cute Vector Joystick for morphing between oscillator banks, for cool performance timbre sweeps and sonic movementVectors can be recorded from the joystick and replayed from trigger sources, or animated from external or internal modulation sources• Super cool retro Big-Pixel screen, ideal for nostalgia freaks or the visually impaired• Wave Warping brings grit and aggression to the FM synthesis with oscillators continuously variable between Sine,Tri-ish Saw, Pulse waveform• Wave Folding for subtle to extreme sonic bending• Two Envelope generators [per voice in polyphonic modes], and two LFOs with all controls assignable as modulation destinations• Intuitive Modulation Slot patching from external and internal sources to be routed to any parameter within the Vector Wave• 30 User Voice storage spaces for storing your synth masterpieces to internal memory, enabling you to impress your friends at a later date• Thee modes of oscillator bank allocation Monophonic Vector, and Polyphonic Voice, and Multitimbral Polyphonic• MIDI input for a spaghetti-free Polyphonic setup, velocity, aftertouch and MIDI CCs avail- able as modulation sources• Slim but handsome Expander Module also available that adds 3 more V/oct and Gate inputs, for maximum mutli-voice multitimbral melodious mayhem!PLEASE NOTE THE KIT IS ONLY SUITABLE FOR EXPERIENCED BUILDERS.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 1 left
V/Oct and Gate expander for RYK Vector Wave.The slim but handsome Vector Wave Expander module, adds 3 extra V/Oct and Gate inputs to the Vector Wave.Using Multi Timbral mode, these extra inputs can control 4 separate monophonic synth voices within the Vector Wave.This is a great way to add multi voice synth parts in a compact and unique Eurorack module!
sold out at the moment
ATTENUVERT x6 is just what it sounds like - six attenuverters in one module!The module consists of six inputs, six outputs and six knobs. Each attenuverter can handle +/- 12V signals. All attenuverters are DC coupled.ATTENUVERT x6 is a very useful utility module for tuning in modulation amplitudes and polarities, but it can also be used to invert gate signals and attenuate audio signals.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
only 1 left
Polyphonic Synth VoiceBread & Butter is a General MIDI based polyphonic synth voice with 128 selectable instruments plus a drums preset. The sound banks have a synthetic and warm quality to them, and the variety of instruments makes this module a flexible and fun addition in any system.Bread & Butter features the standard V/OCT and GATE inputs for triggering the synth voice. Thanks to a polyphony of up to 64, the voices will decay independently making it possible to ratchet chords that decay polyphonically. If the HOLD function is engaged, each note will also sustain. In addition, the MIDI input can be used simultaneously with the V/OCT and GATE inputs. For example; trigger the drums on MIDI channel 10 while generating a bass line via the V/OCT/GATE inputs. The synth voices can also be played polyphonically via MIDI.The module features stereo outputs and the PAN knob lets you spread the polyphonic voices out in the stereo sound field. Parameters such as pitch bend, velocity and instrument selection can be voltage controlled.Features:• CV input range: +/- 5V• Gate input voltage: 3,3-10V• Polyphony: Up to 64 voices (40 voices with sustain)DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.