DIY Kits
sold out at the moment
The PCBSNR is a simple and low power portable noise device based on the Radical Chip (a collaboration between Max Wainwright and Dirty Electronics). 64 different chaotic digital algorithms make harsh noise, video game sounds, pulses and clicks, and more.Two knobs and one button for random algorithm "select".The design is based on the original stripboard version, and is thus very easy to modify and hack. All traces are visible, and cuts and front-side traces are labelled on the back of the circuit board.Features:• Two knobs that change the sound• 64 algorithms with random select• Patchable with pin or socket headers• Jumper for DC coupling for FM etc• Jumper for mono sum (for use with headphones)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
System Sound is a feedback noise device for experimental music, sound design, sound art and more.It has a two channel mixer, a microphone, digital tone generator (sine/noise), two tilt equalisers, effects loop and a power amp. Simple standard circuits are connected in a clever way to enable many kinds of drones, noises, pulsations and chaotic messes even without anything plugged in.Features:• Two inputs with normalised feedback and plenty of gain• A digital tone generator with sine wave/noise + FM switch• A ~1.2W power amp with fast and solid speaker connectors• An electret microphone for electroacoustic feedback• Effects loop with "send blend" and even more gain• Auxiliary line outputDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The ATBase Console v3 is an ATtiny85 synthesizer designed as the centre of a small voltage-controlled setup. Three powered-CV sockets allow external modules to control the first three sound parameters while receiving power through the same TRS cables. Compared with the earlier ATtiny Punk Console design, ATBase extends the frequency range into bass territory. Analogue filter and volume controls shape the output, and different firmware programs expand the available sounds.Features:• ATtiny85 synthesizer with a frequency range extending into bass• Three 0-5 V CV inputs replace the first three parameter controls• Powered-CV links send 5 V power and receive modulation via 3.5 mm TRS cables• Compatible with Noisio ATkeys and ATLFO/EG control-voltage modules• Analogue filter and volume controls• Parallel 3.5 mm and 6.35 mm WAVE outputs• GATE connections and manual trigger button; behaviour depends on firmware• 7-20 V DC supply via a centre-negative 5.5/2.1 mm barrel socketDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
ATkeys is a monophonic control-voltage keyboard for playing compatible synthesizers. Its 24 tactile keys provide two octaves at a time, with an octave control selecting the playing range within a five-octave CV span. A separate gate output follows the keys and can be held on with the latch switch. Power can come from a compatible Noisio powered-CV connection or a suitable USB-to-TRS adapter for use with other CV equipment.Features:• 24 tactile keys with two octaves available at a time• Five-octave CV range from 0 to 5 V at 1 V per octave• Octave potentiometer for selecting the playing range• 5 V gate output and latch switch• Red 3.5 mm TRS connection combines power input and CV output• Separate 5 V CV and gate sockets for external equipment• Requires a compatible powered-CV source or a suitable 5 V adapterDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
only 1 left
ATLFO/EG combines a low-frequency oscillator and an ADSR envelope generator in a compact CV device. Select the operating mode with the button at power-up, then use the four potentiometers to shape modulation or an envelope. The 0-5 V output can control compatible synthesizers, with power supplied by a Noisio powered-CV link or a suitable USB-to-TRS adapter for standalone operation.Features:• Selectable LFO and ADSR envelope-generator modes• Five LFO waveforms: square, sine, triangle, rising ramp and falling ramp• LFO speed, modulation depth and bias controls• Attack, decay, sustain and release controls in envelope mode• Gate input and manual trigger button• 0-5 V control-voltage output and 5 V power input• Powered-CV TRS link plus separate CV output• Manufacturer-specified footprint: 68 × 45 mmDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The ATtiny Punk Console v3 is a programmable 8-bit synthesizer based on the ATtiny85. Four parameter controls and touch contacts let you explore the loaded sound program, while separate tone and volume controls shape the audio output. Its audio bootloader accepts new programs as short audio files through the PROG input, allowing the instrument to take on different sound-generating roles.Features:• ATtiny85-based programmable 8-bit sound engine• Audio bootloader for loading programs through the PROG socket• Four parameter potentiometers with touch contacts• Separate analogue tone and volume controls• 3.5 mm and 6.35 mm audio and synchronisation connections• Black circuit board with white print and printed component values• Reverse-polarity protection for the power supplyDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The Coiler Multi-mode Filter and Rectifier packs an entire nest of sound-shaping features into a single 8HP Eurorack module. It's a two-pole state-variable filter based on a unique integrator design which stores energy in both inductors and capacitors depending on the frequency range. The transition region between the two components, and the saturation characteristics of the traditional OTA-based amplifiers, offer warmth and ever-shifting timbres in the midrange, along with hissing highs and slithering lows. This is a somewhat unpredictable filter.With simultaneous low-pass, band-pass, and high-pass outputs, the Coiler works well in traditional subtractive patches. But its built-in full-wave rectifier is also great for adding harmonics and distortion in patches from the other coast. When combined with low-pass, the rectifier allows the Coiler to serve as a basic envelope follower, for compression and external-signal patches. It's a lot of bite for the buck, and for the rack space.The MSK 009 Coiler VCF is available as a pre-built 6HP Eurorack module or a DIY kit. Slide one into your rack today.Features:• High-quality potentiometers with bushings fastened to the panel for wobble-free operation; conductive plastic for smooth feel; rated for one million operations lifespan (compare to fifteen thousand or less for typical cheap pots)• All-new circuit, not a clone or imitation of anything else• Through-hole for easy hand construction and maintenance• No compromises on build quality: real aluminum panel, not PCB material, with colour printing; nickel and gold plating on the circuit board; close-tolerance metal film fixed resistors.• Fully open design - no lock-inDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
There are hundreds of analog synthesizer VCFs, but only a few core designs. You've got your Moog transistor ladder and imitators that use diodes or other substitutes; you've got your two-pole state variable filter, maybe cascaded to get additional poles; and that's about it. Your grandmother was making electronic music with these designs in the 1960s, and not much has happened since. There are a few more options available in digital and semi-digital (such as switched-capacitor) architectures, but most analog designers have given up trying to create really new filters. Instead, they compete on how well they can imitate or clone specific "vintage" filters.The North Coast Synthesis MSK 007 Leapfrog is new and different, with a sound all its own. The fifth-order "leapfrog" core topology, with five integrators and multiple feedback loops, originates in scientific work more recent than the 1960s and as far as we know never before available in a modular synth VCF. The near-elliptic response curve has an extremely sharp cutoff, with ripple in the passband and nulls in the stopband at frequencies chosen to be musically relevant.Sweep the cutoff and hear each harmonic pop into existence and wobble around before the next one arrives. Choose a timbre, and the temperature compensated volt per octave tracking will keep it consistent across the frequency range. Change it up with exponential and linear frequency modulation. There's even a built-in VCA, because you can never have too many VCAs.Features:• High-quality potentiometers with bushings fastened to the panel for wobble-free operation; conductive plastic for smooth feel; rated for one million operations lifespan (compare to fifteen thousand or less for typical cheap pots)• All-new design, not a clone or imitation of anything else• Ultra-sharp five-pole near-elliptic low-pass response, 61dB/octave at the least steep part of the main cutoff slope, with peaks and nulls at musically relevant frequencies• Built-in VCA switchable to feedback or output modes from the front panel - no jumpers• Temperature compensated V/octave tracking• Through-hole for easy hand construction and maintenance• Connectors between boards, and panel controls mounted on a board - no flying wires• No compromises on build quality: real aluminum panel, not PCB material, with colour printing; panel screwed solidly to both the PCBs and the pots and jacks, for maximum ruggedness; nickel and gold plating on the circuit boards; polystyrene integrator capacitors; close-tolerance metal film fixed resistors; multiturn trimmers.• Fully open design - no lock-inDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
The MSK 008 Voltage-Controlled Octave Switch is a multifunction voltage processor. The module has two channels, each containing a whole-volt quantizer that maps its input to the nearest integer number of volts from -2 to +2; a three-position toggle switch that shifts the quantizer boundaries up or down by a volt; and a precision adder (with optional subtraction function).If you simply route a pitch CV through one of the unquantized CV1 inputs, it can be a performance control, allowing easy transposition up or down an octave at the flip of a switch. That might be useful for VCOs without their own built-in octave switches. With no input signal, it generates a selectable offset of -1, 0, or +1 volts; feed that into an attenuated exponential FM input somewhere and you get the same tactile control over any other interval transposition you choose.But the possibilities really open up when you start using more inputs. An LFO into the quantized input gives the effect of flipping the octave switch under CV control, keeping your hands free to wiggle elsewhere. Using the unquantized inputs, which are normalled across the two channels, you can transpose one sequence by another. The CV2 input can add or subtract, selectable during build by a solder jumper on the circuit board; in a default build, CV2 adds on the left channel and subtracts on the right, but do-it-yourselfers can change this selection, or design their own expanders to make it switchable on the fly.Combining the two channels, with or without other utility modules, allows more complex melody-shifting effects. And it doesn't have to be just for oscillator pitch control. Switching fixed-voltage offsets on filter cutoffs also makes for great drops and timbral shifts. (And try putting the result through a slew limiter!) The default sum and difference configuration allows the module to act as a "mid-side" encoder or decoder. With other patching it can be a flip-flop or a wavefolder.The MSK 008 is fast enough to work on audio. The quantizer is built from hardware comparators, without a microcontroller, and it can do simple bit-crushing effects across the whole audio spectrum. Each channel can also be a unity mixer for audio, with two regular inputs plus the output of the bit-crusher.Features:• Two channels and multiple CV functions in a small space• Flash-style comparator quantization - no microcontroller• Through-hole design for easy hand construction and maintenance• Connectors between boards, and panel controls mounted on a board - no flying wires• No compromises on build quality: real aluminum panel, not PCB material, with colour printing; nickel and gold plating on the circuit boards; close-tolerance metal film fixed resistors; multiturn trimmers.• Fully open design - no lock-inDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
The MSK 010's Wien-bridge oscillator cores produce low-frequency sine waves natively, in a fully analog way with a minimum of harmonic distortion. There are no glitches from waveshaping or stair-steps from insufficiently filtered digital-to-analog conversion. Modulate synthesis parameters with these for smoothly evolving timbres and mind-expanding soundscapes. Because the cores are fully independent and will not synchronize, a patch using multiple LFOs will not repeat its modulation state for a long time, if ever.Choose one of three variants of this module, each with its own set of eight nominal frequencies and cycle times. There are no duplicate or near-duplicate frequencies between different variants, so with two or three, you get the full benefit of a larger modulation palette. Note that the nominal frequencies are just that; every module will have its own one-of-a-kind pattern of exact output frequencies within a few percent of the nominal values, due to component tolerances.• Variant A - 16mHz, 60mHz, 190mHz, 410mHz, 720mHz, 1.3Hz, 4.8Hz, 16Hz (63s cycle time down to 63ms)• Variant B - 34mHz, 88mHz, 160mHz, 280mHz, 600mHz, 1.8Hz, 3.4Hz, 11Hz (30s cycle time down to 94ms)• Variant C - 28mHz, 72mHz, 130mHz, 340mHz, 2.2Hz, 4.1Hz, 7.2Hz, 8.8Hz (35s cycle time down to 110ms)Features:• All-new design, not a clone or imitation of anything else• Fast starting - full amplitude oscillations within one cycle of power-up, unlike the usual behaviour of an oscillating filter• Through-hole design for easy hand construction and maintenance• Connectors between boards, and panel components, mounted on the boards; no flying wires• All three variants build from the same bill of materials; one full kit or PCB set can be used to build any one variant of your choice.• No compromises on build quality: real aluminum panel, not PCB material, with colour printing; nickel and gold plating on the circuit boards; close-tolerance fixed resistors and integration capacitors.• Complete technical documentation released under GPLDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
North Coast makes the Eurorack four-knob utility mixer sound great again with this minimalist design featuring just six transistors. Where a conventional mixer would typically require at least five operational amplifier units each containing a dozen or more transistors, we cut the complexity and distill mixing to its essence. This is a new design made with current components and modern manufacturing quality; but its Class A amplifiers operate on principles that go all the way to the dawn of electronic signal processing.Suitable for both audio and control voltages, with bonus features that don't compromise the minimalist philosophy: positive and negative offset; simultaneous DC- and AC-coupled outputs; maximum gain a little over unity for when you need that extra push over the cliff. It can also function as a transistor distortion effect, by offsetting the signal until it clips and then using the AC-coupled output.Features:• High-quality potentiometers with bushings fastened to the panel for wobble-free operation; conductive plastic for smooth feel• All-new design, not a clone or imitation of anything else• Classic discrete-transistor design style; DIY kit ships with silicon 2N5088 transistors for a clean modern sound, easily modifiable to use other recent or "vintage" types• No ICs!• Through-hole for easy hand construction and maintenance• No compromises on build quality: real aluminum panel, not PCB material, with colour printing; nickel and gold plating on the circuit board; film output coupling capacitor; close-tolerance metal film fixed resistors.• Fully open design - no lock-inDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
North Coast's Transistor ADSR is a four stage traditional envelope generator for Eurorack synthesizers. With full control of four stages, it can shape percussion notes like an AR envelope, organ notes like an ASR, but also the complete range of acoustic-style and classic-synth notes which the simplified envelopes in some popular multi-modules just cannot handle. Use it in subtractive patches for amplitude or filter cutoff, or branch out into controlling other functions, like vibrato amount.At a svelte 6HP and only 33mm deep, the Transistor ADSR can fit in almost any rack. A Schmitt-trigger input allows it to trigger from slowly changing voltage sources, opening the door to special effects like gate delay when the MSK 012 is triggered by another envelope (or another MSK 012). Three timing ranges controlled by a rugged front-panel toggle switch cover a wide range of musical applications, with the fastest settings allowing the envelope to run well into the kilohertz range for audio-rate effects and signal conditioning. The smooth conductive-plastic potentiometers are a tactile joy to play and pay for themselves with increased lifespan.Features:• High-quality potentiometers with bushings fastened to the panel for wobble-free operation; conductive plastic for smooth feel• All-new circuit, not a clone or imitation of anything else• Classic discrete-transistor design• No ICs!• Through-hole for easy hand construction and maintenance• No compromises on build quality: real aluminum panel, not PCB material, with colour printing; nickel and gold plating on the circuit board; poly film timing capacitors; close-tolerance metal film fixed resistors.• Fully open design - no lock-inDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
North Coast's complex VCO is comfortable on a journey to the East or the West, while providing a stable foundation at home in any Eurorack. The module contains two triangle-core VCOs, each with four waveforms and standard V/octave control. As basic VCOs running independently these can be the heart of a traditional subtractive East Coast synthesizer. But the Middle Path's oscillators can also be used together, with or without sync, to drive its unique multi-output Gilbert-style sine shaper. The shaper, which can also take external input, offers wave shaping, distortion, folding, phase modulation including through-zero, and imitation stereo. These effects take the sound into West Coast territory.The design emphasis is on harmonious combination of simple principles. The exponential converter uses premium analog multipliers and a transistor array to ensure temperature stability without fiddly adjustments or hard-to-control "tempco" resistors; it should provide consistent tracking, and especially between the two oscillators, without needing to warm up. The triangle cores are intrinsically frequency-accurate without needing extra circuitry to compensate for reset time. The sine shaper includes our own novel quadrature modification which can be used to generate a stereo signal or in combination with other modules to create frequency shift effects. The sync circuit joins the oscillator cores in another way with a selection of soft and firm modes.Features:• High-quality potentiometers with bushings fastened to the panel for wobble-free operation; conductive plastic for smooth feel• Normalization to the Eurorack bus allowing it to receive pitch control without needing an input patch• All-new design, not a clone or imitation of anything else. Innovative quadrature sine shaper offering through-zero phase modulation with a range of up to 1080°• Genuine AD633 and THAT320 chips in the exponential converter; sockets on all DIP ICs• Through-hole for easy hand construction and maintenance• Connectors between boards, and panel controls mounted on a board - no flying wires• No compromises on build quality: real aluminum panel, not PCB material, with colour printing; panel screwed solidly to both the PCBs and the pots and jacks, for maximum ruggedness; nickel and gold plating on the circuit boards; close-tolerance metal film fixed resistors.• Fully open design - no lock-in.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Crum Drum is a 4-voice drum machine with built in randomization and probability based sequencing designed by NYSTRÖMRhythms can be created and manipulated using the internal random sequencer or externally via MIDI USB. Press the beat button to generate new rhythms, adjust the probability to create continuous variations, and increase the randomness to modulate the sound of your beats! Generated sequences can also be sent out via MIDI USB and Crum Drum can also sync via analog clock in and out.The four voices of Crum Drum are Kick, Snare, HiHat and Bass (FM). There are 8 parameters knobs to sculpt the character of each voice allowing for wide variety of tones. It’s easy to create varied and organic sequences by adding modulation via the Probability and Randomness controls. Probability sets the chance that the selected voice will play per step of the sequence, while randomness increases the parameter modulation for each voice. The higher the randomness, the more each instrument parameter is modulated per step. Some of the instrument parameter controls have different behaviours depending on which voice is selected, so make sure to check the user manual for full details.Crum Drum features four global effects which are: Overdrive, Reverb, Delay and Swing. The delay-time is tempo synced and the subdivided differently dependent on the BPM.Power is provided via micro usb cable (not included)Features:• 4 instruments: Kick, Snare, HiHat, Bass• 8 sound parameters per instrument• Overdrive, Reverb, Delay & Swing• Send & Recieve Analog & Midi USB clock• Send & Receive Midi USB sequencing• Randomised and probability based sequencing
available
Crum Hum is a 3-voice experimental and expressive soundscaping instrument designed for generative and ever-evolving melodic and harmonic creation.The Crum Hum features 12 sound engines which range from simple sawtooth and square waves with lowpass filtering, to various wavetable and FM engines and more complex setups like bass, chords, and melody. There are also 12 different built-in scales to play with.Each of the three voices has a triangular touchpad that lets you control the timbre and volume simultaneously. Each voice also offers a Frequency knob for setting the lowest possible note, as well as a Random knob that sets the probability of notes being played for each clock pulse.The Tone knob affects the timbre of all three voices simultaneously. What it does exactly depends on the selected sound engine and the tone can also be randomized for subtle to drastic sonic variations at each clock pulse.Moreover, Crum Hum features built-in delay, reverb, and overdrive effects, as well as an LFO that can modulate the frequency, tone, or volume. There’s an internal clock generator, but it’s also possible to sync the synth to an external clock source. Most parameters can be controlled via MIDI CC (see the user manual for more details).In addition to a stereo audio output, Crum Hum features a CV output that corresponds to the touchpads, allowing for expressive control of other modular instruments.Features:• 3 x melodic voices with expressive touch control• 12 x different sound engines• Generative & randomized melodic and chord generation• 12 x different scales• Built-in delay, reverb, overdrive and LFO• 3.5mm CV output• 3.5mm Clock input• Send and receive Midi sequencing and Midi CC.
sold out at the moment
The Blast module is designed to make crafting great kick drums easier. It helps you overcome the challenges of balancing low-end depth, midrange impact, and high-frequency clarity to create kicks that feel powerful and sound cohesive.Blast focuses on the essential elements of a kick drum: delivering enough punch to stand out in the mix while maintaining a full, rich sustain. Its unique envelope offers a fast decay with a slower release for amplitude, ensuring a tight, punchy transient without sacrificing fullness. In addition, the Body Control feature allows you to increase the weight of the kick, adding depth and power without overpowering the mix. With tools like compression, envelope shaping, and subtle distortion, Blast gives you the flexibility to shape the transient for just the right amount of impact and definition-without overcomplicating the process.Whether you're looking for a clean, punchy sound or a more versatile tone, Blast offers intuitive controls that adapt to a wide range of musical styles. It's designed to help you get the sound you want easily and effectively, without compromising quality.Features:• Analog kick drum module• Manual and trigger input• Separate amplitude and pitch decay controls, both with CV inputs• Unique envelope provides a fast decay with a slower release• Body control to increase the weight of the kick• Compression with soft clipping• Pitch amount to determine how offset the initial pitch is• Blendable waveshape distortion with wave folding• Thru-zero FM input• AM input• Accent input with level/accent attenuator• Tuning control and 1V/Oct input for consistent pitch tracking• Final output plus a unipolar positive and unipolar negative amp envelope outputsDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
2 HP dual buffered Multiple features 2 channels of 3 outputs or 1 channel of 6 outputs if nothing is connected to the second input, it has 2 bi-colour led showing positive and negative voltage.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 1 left
CV Looper Interface. Record and playback LFOs, knob movements, CV, ADSRs, audio etc! This is a high-resolution dual-channel recording interface for your signals. Please check this video to get an idea what Ephemere is.You can record from 1014sec at 172Hz up to 4 seconds at 44.1kHz of signal on each channel, change the playback speed also it scan through the recorded CV. It has an Oled display to monitor your live and recorded signal to adjust playback length. When nothing is patched to the input you can use the input pot as an offset/cv generator to record pot movements into the module. It´s possible to save, load your signals in the sdCard up to 16GB of space. There are 4 different modes to record to choose from to make more complex signals and 3 different play modes either.Features:• 2 Channels signal interface recording• Record modes (manual, sync, manual multi, sync multi)• Play modes (forward, backward, pendulum)• 1014 seconds at 172Hz up to 4 seconds at 44.1kHz to select from the menu.• Oled display with 2 types of signal monitoring• Speed control /5 to x5• Signal recording select from the menu -5V/+5V or 0V/10V• Save, Load, erase files from 16GB SDcard• Easy remote updates• CV control from 0V to 10VDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Etna is an advanced triple control analog multimode morphing filter, meticulously designed for precise and dynamic sound shaping. It allows for rapid or smooth transitions between diverse filter settings, known as snapshots.Each snapshot comprehensively defines all of the filter’s parameters, which can be adjusted either swiftly or gradually. These transitions are controlled through an applied voltage or clock and triggers, with the flexibility to use up to eight distinct stages for creating complex filtering effects in a variety of audio applications.In addition to its morphing capabilities, Etna incorporates analog controls that enable real-time, expressive modifications to the parameters of each saved snapshot. This enhancement not only enriches the morphing process but also provides a tactile, live experience that adds significant depth and nuance to the audio output, making it a powerful tool for both studio and live performance settings.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Dual Attenuverter with Sum OutputInverted output, 5v or 10v constant voltage when no input is connected.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.