ADDAC System - 712 Vintage Pre
available
ADDAC712 is a dual channel discrete gain staging amplifier, based on a famous discrete preamp board from the 70’s used in some legendary equipment. What caught our attention was the character of it’s clipping and resulting saturation/distortion.
The module can be used with modular signals to add a distortion/fuzz character or as a preamp for an external source such as a line source, keyboard, guitar... It’s also a great side companion for our ADDAC711 Balanced Inputs.
At the top an On/Off [BYPASS] switch routes the signal into the Effect (Up: Active) or to the bottom output gain stage (Down: Bypassed).
The amount of amplification is set by the [GAIN] control, the maximum amount of amplification can be set by the user using the [MAX GAIN] trimmer.
Up to ±5,5v the incoming signal will keep it’s integrity, beyond this point saturation will start to increase. At approx. ±6v a hard clipping will start to occur, this clipping also has a particular quality that at extreme levels it drifts the audio 0v bias reference, moving it upwards which results are similar to a Gate effect.
In the middle, an x2 op-amp based output gain stage with a clipping LED, which monitors the clipping at the output, and an [OUTPUT] control to set the output volume.
Having the top and middle gain stages provides flexibility allowing the user to completely distort the signal on the top stage and tame it’s output level with the second stage.
At the bottom, input and output for both channels (left input is normalled into right input).
DIY-Kit-Type:
SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€105.91*
Befaco - FX Boy
available
A Multi FX module based on game carts!Fx Boy is a multi-FX module designed in collaboration with several talented manufacturers. This is an effect unit with CV control over the parameters and dry/wet control, with a Built-in CV controllable four bands EQ.Each effect is physically hosted in a hot-swappable game cart and designed by a different manufacturer: Touell Skouarn with Skuara a harsh fuzz with overdrive, Instruo with micro Phaser, a two-flavoured Phaser, Feedback modules with a vintage Flanger, XOR with FX-Girl, a digital double effect module: Delay + Granularizer, Making sound machines with an analog Wave folder, Tesseract with a bit crusher and Befaco Trash distortion!Please note that the cards add current consumption on top of the values stated here.Features:• CV control over all parameters and dry/wet• CV controllable four-band EQ, routable post or pre-effect.• Selector for two different flavours of each cart.• Open specifications to design your own carts• Hot swap for all carts. (A tiny pop can occur depending on the cartridge design)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€359.00*
Neutral Labs - Elmyra 2 (Desktop)
available
This is the standalone version of Elmyra 2. Elmyra 2 is a 4-voice digital/analog hybrid platform for microtonal sonic exploration, capable of creating anything from lush ambient soundscapes to gritty droning textures and shrieking noises, available as a 42 HP Eurorack module or semi-modular desktop synth. With 31 modulation targets, 4 polymetric sequencers, delay, additional per-voice effects, a choice of various filters, as well as onboard LFOs and utilities, it is essentially a purpose-built small modular system in itself. A set of preset cards (included) or electronic components like capacitors or diodes can be plugged into the front panel in order to change the sound character.Features:• 4 independent voices activated by touch or CV• wavetable-based complex oscillator engine, up to 12 oscillators in total, 1V/octave compatible• chromatic mode makes chords and harmonic sounds possible, microtonal scales supported• 41 patch points• 31 modulation targets• touchpads with analog envelopes that can be used as modulation sources• resonant filter switchable between:• boomy and aggressive multimode 2-pole state variable filter (low-pass, band-pass, high-pass)• creamy 4-pole low-pass ladder filter• delay with unhealthy amounts of feedback• lo-fi reverb• analog OUCH circuit: a unique combination of destructive distortion, waveshaping and filtering• sonic character can be customised by using special preset cards (set of 4 included) or components like diodes that can be plugged into the front panel• preset cards can be used with other Neutral Labs modules• external audio can be processed via audio input• 9 per-voice modulations and effects:• unison detune• dual sub-oscillators• saturation• bitmangler• sample rate reduction• noise• high-pass filter• low-pass filter• 2 LFOs: 1 sine, 1 complex morphable• 4 sequencers with arbitrary step length per voice (up to 128), allows polymetric structures• delay time and LFOs can be clock-synced or unsynced (tap tempo is also possible)• utilities• dual attenuator/buffered multiple/voltage generator• CV summing circuit• case made of plant-based bioplastic and native German oakwood• boutique synth handmade in GermanyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€379.00*
Neutral Labs - Elmyra 2 (Eurorack)
only 2 left
This is the Eurorack version of Elmyra 2. Elmyra 2 is a 4-voice digital/analog hybrid platform for microtonal sonic exploration, capable of creating anything from lush ambient soundscapes to gritty droning textures and shrieking noises, available as a 42 HP Eurorack module or semi-modular desktop synth. With 31 modulation targets, 4 polymetric sequencers, delay, additional per-voice effects, a choice of various filters, as well as onboard LFOs and utilities, it is essentially a purpose-built small modular system in itself. A set of preset cards (included) or electronic components like capacitors or diodes can be plugged into the front panel in order to change the sound character.Features:• 4 independent voices activated by touch or CV• wavetable-based complex oscillator engine, up to 12 oscillators in total, 1V/octave compatible• chromatic mode makes chords and harmonic sounds possible, microtonal scales supported• 41 patch points• 31 modulation targets• touchpads with analog envelopes that can be used as modulation sources• resonant filter switchable between:• boomy and aggressive multimode 2-pole state variable filter (low-pass, band-pass, high-pass)• creamy 4-pole low-pass ladder filter• delay with unhealthy amounts of feedback• lo-fi reverb• analog OUCH circuit: a unique combination of destructive distortion, waveshaping and filtering• sonic character can be customised by using special preset cards (set of 4 included) or components like diodes that can be plugged into the front panel• preset cards can be used with other Neutral Labs modules• external audio can be processed via audio input• 9 per-voice modulations and effects:• unison detune• dual sub-oscillators• saturation• bitmangler• sample rate reduction• noise• high-pass filter• low-pass filter• 2 LFOs: 1 sine, 1 complex morphable• 4 sequencers with arbitrary step length per voice (up to 128), allows polymetric structures• delay time and LFOs can be clock-synced or unsynced (tap tempo is also possible)• utilities• dual attenuator/buffered multiple/voltage generator• CV summing circuit• case made of plant-based bioplastic and native German oakwood• boutique synth handmade in GermanyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€329.00*
Neutral Labs - Meg
available
Meg is a unique kind of waveshaper. Instead of folding the wave back in on itself like a common wavefolder, it shifts parts of the wave up or down, with the shifting threshold being adjustable. The resulting 2 half-waves can be flattened one by one, essentially morphing into a half square wave and eventually a full square wave. Essentially, it will add pulse-width modulation (and more) to any kind of wave. Both knobs can be fully CV controlled.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€49.00*