333modules - Multiply
available
Utility module with either buffered multiply and summing sections. 1 In to 8 Out or 2 In to 4 Out operation are selectable at multiply section. On summing section 2 sets of 4 signals can be summed to its related output.Features:• 1 In to 8 Out or 2 In to 4 Output (desconexion).• 2 x 4 signals summed Output.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€83.30*
4ms - Passive Mult
sold out at the moment
The Passive Mult is a two channel multiple. It can behave as a dual one to three mult, or in a single channel/normalized one to six configuration. Since the device is passive it can also be used as a three to one, or six to one mixer!This module requires no power, so all you have to do is build up and install it in your enclosure with the supplied 3mm screws.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€22.61*
Feedback Modules - CP3+
only 2 left
The CP3PLUS is an accurate recreation in Eurorack format of one of the most appreciated vintage modular audio mixers. The specific distortion makes it not only a great summing unit but also a great sound design tool. The included MULTI is a welcome bonus.Features:• 4 mono analog input• 4 input level pots• 1 dual level pot• One inverting and one non-inverting output jacks• One 4 jack passive multiple• Standard 10 pin euro power (+12V / -12V)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€46.41*
Feedback Modules - Multi
sold out at the moment
Multi it's an 8 jack unbuffered multiple with front panel in black/gold Feedback style.It's separated in 2x4 sections with jack's 4 link going to jack 5.So you can use it as two independent multiples or one single 7 jack multiple.It uses PJ301BM jack, for a better strength of the module.This kit contains all the parts needed to build a complete MULTI module.No manual needed. All parts included, only through-hole (THT) parts to solder, no SMD parts.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€15.01*
Jolin - Agogo
available
AGOGO is an octal analogue vactrol-based low pass gate and mixer in a cascade configuration. Each one of its input, CV and output is normalized and buffered to the next one: it can be used as a multiplier and a mixer for both audio and CV.Inputs are normalled and outputs are mixed: thanks to this configuration it can be used as a modulation matrix and a signal router. More units can be chained to increase the number of I/O.Features:• 8 independent vactrol LPGs.• Classic logarithmic vactrol curve and latency.• Two LPG flavours: brighter - blue LEDs - and darker - red LEDs.• Open design signal path: break the normalization at any point to change its configuration.• Input and CV are normalled and they flow top to bottom when no jack is inserted.• Outputs are summed to create sub-mix on the go.• Unlimited units can be chained together.• Works with audio and CV sources.• “Whatever” power connector a.k.a. don’t mind the polarityDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€224.91*
LeafAudio - MLT (1U)
available
The MLT Passive Multiple is a 1 input to 6 output or 2 input to 3 output signal multiplier. If nothing is patched into input 2, it is normalized to input 1. As the device is passive, it can also be used to combine signals. For example 3-to-1 or 6-to-1. This DIY kit is very beginner friendly.Passive module, no power required.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€17.85*
LeafAudio - MLT (2HP Passive Multiple)
available
The MLT Passive Multiple is a 1 input to 6 output or 2 input to 3 output signal multiplier. If nothing is patched into input 2, it is normalized to input 1. As the device is passive, it can also be used to combine signals. For example 3-to-1 or 6-to-1. This DIY kit is very beginner friendly.Passive module, no power required.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
€17.85*
Making Sound Machines - Multiplikand
available
Multiplikand is a compact routing utility module for Eurorack in 6HP. It takes Audio and CV, with optional DC filtering.At its core, Multiplikand offers four active precision multiples. Clever normalisation and a switch allow you to configure how the signals are summed.The module has pin headers in the back so you can break out from prototyping platforms like Arduino, Teensy, Daisy and Bela to Multiplikand's inputs with jumper wires.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€89.50*
MRG Synthesizer - MULTI
only 1 left
This is a simple module that allows to duplicate signals.Each column can be used either as a dual 1x3 multiple, or as a 1x5 multiplier, depending on the presence of a jack in slots 3 and 4.Really simple, but incredibly useful.It is passive, thus requires no external power.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€35.00*
Patching Panda - Copy Cat
only 2 left
2 HP dual buffered Multiple features 2 channels of 3 outputs or 1 channel of 6 outputs if nothing is connected to the second input, it has 2 bi-colour led showing positive and negative voltage.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
€44.03*
Transient Modules - u2x
sold out at the moment
The u2X is a dual buffered multiple DIY kit for the 1U Intellijel format. With bicolor LEDs for monitoring signals. Each input is copied into three outputs. As the top section is normalled to the bottom section it’s also possible to get 6 copies of the same signal.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
€35.70*