Case
available
Befaco’s regulated power bus features linear regulators for each rail and guarantees up to 1.5A of current without voltage drops and with minimum noise leakage.It comes with faston blades for daisy chaining several busses together for monster cases!Works best with our switched power supply.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Ready to feed the most modern and power-hungry modules.A 5A power solution, 28 slots powered by four high-quality DC-DC converters.ON/OFF 4 HP - 3U module with 2 USB-A charging ports and a power button.Friendly Plug and Play, tools are not required.Features:• 25 mm height over regulators grid and 15 mm height on the rest of the bus• Horizontal connectors to maximize space• 2,5 mm barrel power connector• On/Off 4 HP module• 2 USB-A charging ports• Power brick: 135 W 2,5 mm barrel connector center positive (included)• Current: +12 V: 5 A, -12 V: 2,5 A, 5 V: 4 A• Measurements: 423 mm x 80 mmDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Shield is a filtered Eurorack power distribution busboard for the Black Noise Modular VOLT55 ecosystem. Its connectors are divided into separate analog and digital zones to reduce noise passing from digital modules into the analog signal path. Multiple boards can be daisy-chained to expand a system. This is the assembled version, supplied with a connection cable and six adhesive mounting feet. First-generation VOLT55 units require a dedicated compatibility cable.Features• 28 filtered module power connectors• Separate zones for analog and digital modules• Daisy-chain connection for additional busboards• Designed for VOLT55 power supplies• Board dimensions: 245 × 65 mm; height: 12 mm• Connection cable and six adhesive mounting feet included• Assembled version
available
VOLT55 + Shield combines a compact USB-C-powered Eurorack power supply with a filtered distribution busboard. Available as VOLT55 S, M or L, the system provides isolated power rails for studio, stage and portable setups using a compatible USB-C PD adapter or power bank. The Shield offers 28 module connectors in separate analog and digital zones to reduce interference, and additional Shields can be daisy-chained. Three front-panel USB-A ports supply external devices and share the +5V rail with your modules.Choose the capacity that suits your system:VOLT55 S: +12V 2500mA / -12V 1250mA / +5V 2000mA.VOLT55 M: +12V 4000mA / -12V 2500mA / +5V 2000mA.VOLT55 L: +12V 5000mA / -12V 2500mA / +5V 2000mA.S requires a USB-C PD source rated for at least 65W at 20V/3.25A; M and L require at least 100W at 20V/5A. The external power source is not included.Features:• USB-C Power Delivery 3.0 input• Isolated power conversion and filtered distribution• 28 Shield connectors in analog/digital zones• Daisy-chain expansion with additional Shields• Three USB-A power outputs sharing the +5V rail• Soft-start; voltage, current, short-circuit and temperature protection• Shield connection cable and six adhesive feet included
only 2 left
The usual bus ribbon cable to connect your modules to your busboard and PSU to supply them with power.We have different lengths and versions – the standard 16 to 10 pin version and the 16 to 16 pin version to supply your modules with 5V as well as the gate and CV bus connections.
available
This PSU connector makes it easy to supply power to your Eurorack modules within the DIY.EDU Labor environment. It provides a simple interface for connecting modules to the Labor’s internal power distribution.Features:• Power connector for integrating Eurorack modules into the Labor• Compatible with the DIY.EDU Labor workspace• Simplifies prototyping and testing of powered modules• Compact and easy to installDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
This is our new double rail! If you build a case with two or more rows, you can place this one in the middle and save 1 rail. Instead of 4 rails you only need 3 for a two row system.We recommend to use them with our new side brackets 3U + 1U, which need 2 low profile rails and 1 double rail to create a resulting frame of 1x 3U + 1x 1U (Intellijel).84 HP = 427mm104 HP = 529mm114 HP = 579mm126 HP = 640mm168 HP = 854mm196 HP = 996mmRail (one piece, threaded strip not included) for building DIY Eurorack cases.Type A rails feature a lid, which holds your modules in place so they cannot move up and down.For building your case you also might need some additionals: threaded strips and M3 screws holding your modules and M5 screws for mounting the rails (we have various types of screws here). As an alternative to the M3 threaded strips you can also use M3 slide nuts.The hole where the M5 screw sits later has no threading - an M5 screw will carve its way when you insert them. Alternatively you could use a tapping tool, but it's not really necessary.
available
This is our new double rail! If you build a case with two or more rows, you can place this one in the middle and save 1 rail. Instead of 4 rails you only need 3 for a two row system.We recommend to use them with our new side brackets 3U + 1U, which need 2 low profile rails and 1 double rail to create a resulting frame of 1x 3U + 1x 1U (Intellijel).Rail (one piece, threaded strip not included) for building DIY Eurorack cases.84 HP = 427mm104 HP = 529mm114 HP = 579mm126 HP = 640mm168 HP = 854mm196 HP = 996mmType A rails feature a lid, which holds your modules in place so they cannot move up and down.For building your case you also might need some additionals: threaded strips and M3 screws holding your modules and M5 screws for mounting the rails (we have various types of screws here). As an alternative to the M3 threaded strips you can also use M3 slide nuts.The hole where the M5 screw sits later has no threading - an M5 screw will carve its way when you insert them. Alternatively you could use a tapping tool, but it's not really necessary.
available
This is our new double rail! If you build a case with two or more rows, you can place this one in the middle and save 1 rail. Instead of 4 rails you only need 3 for a two row system.We recommend to use them with our new side brackets 3U + 1U, which need 2 low profile rails and 1 double rail to create a resulting frame of 1x 3U + 1x 1U (Intellijel).Rail (one piece, threaded strip not included) for building DIY Eurorack cases.84 HP = 427mm104 HP = 529mm114 HP = 579mm126 HP = 640mm168 HP = 854mm196 HP = 996mmType A rails feature a lid, which holds your modules in place so they cannot move up and down.For building your case you also might need some additionals: threaded strips and M3 screws holding your modules and M5 screws for mounting the rails (we have various types of screws here). As an alternative to the M3 threaded strips you can also use M3 slide nuts.The hole where the M5 screw sits later has no threading - an M5 screw will carve its way when you insert them. Alternatively you could use a tapping tool, but it's not really necessary.
available
This is our new double rail! If you build a case with two or more rows, you can place this one in the middle and save 1 rail. Instead of 4 rails you only need 3 for a two row system.We recommend to use them with our new side brackets 3U + 1U, which need 2 low profile rails and 1 double rail to create a resulting frame of 1x 3U + 1x 1U (Intellijel).Rail (one piece, threaded strip not included) for building DIY Eurorack cases. 84 HP = 427mm104 HP = 529mm114 HP = 579mm126 HP = 640mm168 HP = 854mm196 HP = 996mmType A rails feature a lid, which holds your modules in place so they cannot move up and down.For building your case you also might need some additionals: threaded strips and M3 screws holding your modules and M5 screws for mounting the rails (we have various types of screws here). As an alternative to the M3 threaded strips you can also use M3 slide nuts.The hole where the M5 screw sits later has no threading - an M5 screw will carve its way when you insert them. Alternatively you could use a tapping tool, but it's not really necessary.
available
Low profile Rails are smaller and lighter than the standard ones. The basis is the same as Type A standard but without the whole back.Rail (one piece, threaded strip not included) for building DIY Eurorack cases. 84 HP = 427mm104 HP = 529mm114 HP = 579mm126 HP = 640mm168 HP = 854mm196 HP = 996mmType A rails feature a lid, which holds your modules in place so they cannot move up and down.For building your case you also might need some additionals: threaded strips and M3 screws holding your modules and M5 screws for mounting the rails (we have various types of screws here). As an alternative to the M3 threaded strips you can also use M3 slide nuts.The hole where the M5 screw sits later has no threading - an M5 screw will carve its way when you insert them. Alternatively you could use a tapping tool, but it's not really necessary.
available
Low profile Rails are smaller and lighter than the standard ones. The basis is the same as Type A standard but without the whole back.Rail (one piece, threaded strip not included) for building DIY Eurorack cases.84 HP = 427mm104 HP = 529mm114 HP = 579mm126 HP = 640mm168 HP = 854mm196 HP = 996mmType A rails feature a lid, which holds your modules in place so they cannot move up and down.For building your case you also might need some additionals: threaded strips and M3 screws holding your modules and M5 screws for mounting the rails (we have various types of screws here). As an alternative to the M3 threaded strips you can also use M3 slide nuts.The hole where the M5 screw sits later has no threading - an M5 screw will carve its way when you insert them. Alternatively you could use a tapping tool, but it's not really necessary.
available
Low profile Rails are smaller and lighter than the standard ones. The basis is the same as Type A standard but without the whole back.Rail (one piece, threaded strip not included) for building DIY Eurorack cases.84 HP = 427mm104 HP = 529mm114 HP = 579mm126 HP = 640mm168 HP = 854mm196 HP = 996mmType A rails feature a lid, which holds your modules in place so they cannot move up and down.For building your case you also might need some additionals: threaded strips and M3 screws holding your modules and M5 screws for mounting the rails (we have various types of screws here). As an alternative to the M3 threaded strips you can also use M3 slide nuts.The hole where the M5 screw sits later has no threading - an M5 screw will carve its way when you insert them. Alternatively you could use a tapping tool, but it's not really necessary.
available
Low profile Rails are smaller and lighter than the standard ones. The basis is the same as Type A standard but without the whole back.Rail (one piece, threaded strip not included) for building DIY Eurorack cases.84 HP = 427mm104 HP = 529mm114 HP = 579mm126 HP = 640mm168 HP = 854mm196 HP = 996mmType A rails feature a lid, which holds your modules in place so they cannot move up and down.For building your case you also might need some additionals: threaded strips and M3 screws holding your modules and M5 screws for mounting the rails (we have various types of screws here). As an alternative to the M3 threaded strips you can also use M3 slide nuts.The hole where the M5 screw sits later has no threading - an M5 screw will carve its way when you insert them. Alternatively you could use a tapping tool, but it's not really necessary.
available
These ones are smaller and lighter than the standard ones. The basis is the same as Type B standard but without the whole back. Type B rails DO NOT feature a lid, they are thinner.Rail (one piece, threaded strip not included) for building DIY Eurorack cases.84 HP = 427mm104 HP = 529mm114 HP = 579mm126 HP = 640mm168 HP = 854mm196 HP = 996mmFor building your case you also might need some additionals: threaded strips and M3 screws holding your modules and M5 screws for mounting the rails (we have various types of screws here). As an alternative to the M3 threaded strips you can also use M3 slide nuts.The hole where the M5 screw sits later has no threading - an M5 screw will carve its way when you insert them. Alternatively you could use a tapping tool, but it's not really necessary.
available
Rail (one piece, threaded strip not included) for building DIY Eurorack cases. Black anodized aluminium.84 HP = 427mm104 HP = 529mm114 HP = 579mm126 HP = 640mm168 HP = 854mm196 HP = 996mmType A rails feature a lid, which holds your modules in place so they cannot move up and down.For building your case you also might need some additionals: threaded strips and M3 screws holding your modules and M5 screws for mounting the rails (we have various types of screws here). As an alternative to the M3 threaded strips you can also use M3 slide nuts.The hole where the M5 screw sits later has no threading - an M5 screw will carve its way when you insert them. Alternatively you could use a tapping tool, but it's not really necessary.
available
Rail (one piece, threaded strip not included) for building DIY Eurorack cases. Silver anodized aluminium.84 HP = 427mm104 HP = 529mm114 HP = 579mm126 HP = 640mm168 HP = 854mm196 HP = 996mmType A rails feature a lid, which holds your modules in place so they cannot move up and down.For building your case you also might need some additionals: threaded strips and M3 screws holding your modules and M5 screws for mounting the rails (we have various types of screws here). As an alternative to the M3 threaded strips you can also use M3 slide nuts.The hole where the M5 screw sits later has no threading - an M5 screw will carve its way when you insert them. Alternatively you could use a tapping tool, but it's not really necessary.
available
Rail (one piece, threaded strip not included) for building DIY Eurorack cases. Silver anodized aluminium.84 HP = 427mm104 HP = 529mm114 HP = 579mm126 HP = 640mm168 HP = 854mm196 HP = 996mmType B rails DO NOT feature a lid, they are thinner.For building your case you also might need some additionals: threaded strips and M3 screws holding your modules and M5 screws for mounting the rails (we have various types of screws here).As an alternative to the M3 threaded strips you can also use M3 slide nuts.The hole where the M5 screw sits later has no threading - an M5 screw will carve its way when you insert them. Alternatively you could use a tapping tool, but it's not really necessary.
available
M3 slide nuts for Eurorack rails. This are packs of 50 pieces. They can be used as an alternative to our threaded strips for all Eurorack rails.
sold out at the moment
A mini power distribution board. This kit contains all the parts needed to build a complete Distribution Mini. There's no build guide available from the manufacturer, but it is really easy to build it. If you have questions, please email Freedback Modules!DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.