Clock Modulator
sold out at the moment
Eleven rhythmic outputs for wONkY drum patterns.• Pulses turns the sequence from the main Turing Machine into a series of repeating rhythmic semi-random clock signals, that are based on the main clock input.• Seven of the 11 outputs are just the binary steps of the sequence on the front panel of the main module. The other four are derived from those pulses - so when steps 1+2 are active, the 1+2 output pulses.• As with most of the Turing Machine features, it is hard to explain, but very easy and intuitive in practice: send pulses from the module to anything that takes a rhythmic pulse; envelope generators, FM Index inputs, drum modules or other sequencers. Very complex polyrhythms come easily.• Because the Pulses are all related to the main module, they randomise, lock and change with that module. With the main module's big knob at 12 o'clock, the pulses are random. At 5 o'clock, they are locked, and at 3 o'clock they will 'slip' slowly over time.• You can try out a fully operational Turing Machine + Pulses + Volts in the free VCV Rack software.• Pulses connects around the back with a 16-way ribbon cable and works with any Turing Machine (Mk2, or Mk1 with the backpack).• Pulses uses Surface Mount components but is still a very simple build for anyone who has done a bit of through hole soldering beforehand.• Here is an epic series of videos from mixolydian2010 that documents the whole build process• Here's a very old audio demo from when I was developing Pulses, which shows the kind of polyrhythmic craziness it can create.• Despite involving SMD components, Pulses is a very straightforward DIY build, that most people complete without any problems. If you get stuck, the Pulses Github Issue List or the main Turing Machine issue list are probably the best places to start.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Startup is a headphone amp, six-input mixer, tap tempo clock, divider & multiplier in 4hp. It's the perfect way to start a small Eurorack case. Full DIY Kit.Startup is designed to be the best way to start a small Eurorack case, featuring a Mixer, Clock & Headphone Amp. This is a really easy project for DIY newcomers, all the SMD components come pre-soldered and the PCB is programmed and testing prior to shipping. You just need to solder the buttons, jacks and pot. The Music Thing Modular ‘Startup’ is designed to be the best way to help start a small Eurorack case.This 4HP module does three things:1) It’s a 5 channel output mixer, with a spare channel for stereo signals (like a Korg Volca or a phone).2) It’s a nice clean headphone amp with two outputs.3) It’s a useful tap-tempo clock, with a second channel giving divided or multiplied clocks.The best way to understand Startup is with with the Quick Start Manual. (Use button below)DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Particles, is 4 channels of trigger modulation, capable of mathematically variating and manipulating your patterns with a combination of fun features to play with. It can evolve your rhythmic idea into more complex and groovy patterns which are difficult to achieve without music knowledge.You can create your algorithms from the rhythmic tools provided to be able to change the patterns instantaneously in many ways without worrying to sacrifice the original idea.You can shift and scramble the outputs, you can repeat the triggers with different time signatures to transform the grooves, mute in different ways, disappear by probability trigger inputs, disappear by probability repetitions, use sequential switching to shift randomly with a different kind of resetting, bypass each channel and set it individually the amount of each feature per channel when feeding external CV.The idea of Particles, was designed to provide features for building complex breaks, grooves, organic-evolving percussion sounds, different options for arpeggios, and even bass line grooves, the limits are decided by you.Features:• 4 trigger inputs/outs.• Repetitions with different distribution time to choose from.• Manually shift the output channels, scramble them randomly or clocked them in foward mode.• Reset the ouputs to 4 different shift modes.• Dissapear repetitions by probability per channel.• Dissapear the input trigger by probability per channel.• Mute each channel with clock divisions from input clock.• Mute manually the outputs• Disable triplets from repetitions to have musical patterns• Random volatges output clocked from clock input.• The slider keeps the adjusted value from each feature.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Λόγοι is a voltage controlled clock divider, counter, and delay. It subdivides and adds time, creating organic, evolving signatures. Λόγοι brings movement and life to the trigger signal, from a subtle swing to bizarrely complex and intricate rhythms. Instructions The functions of Λόγοι are split with division on the left, and addition on the right. The right side operates either in Counter mode, by adding clocks, or Swing mode, by adding a time delay. The mode is set by the centre switch. The module has CV inputs (top jacks) and trigger outputs (middle left/right jacks) for each side, and a combined trigger output (centre bottom jack) which gives the output of both operations: divide and add. The trigger input (bottom left and right jacks) is shared between division and addition. There is also a reset input (middle centre jack) and manual reset switch (push switch up). There are three LEDs indicating the divided and added output to the left and right, and the combined output in the centre. Divide The divider toggles its output every n clocks, where n is the divisor. The divisor is set with a manual (top knob) and CV level control, in a range from 1 to 32. Count With the switch in the down position, the additive side functions as clock counter. The counter will output a trigger signal every m clocks, where m is the addend. The range is from 1 to 32 clocks, with 16 in the centre position. The combined output will divide and count. If i is the incoming clock, n the divisor, and m the addend, then it will output a a trigger signal every i/n + m clocks. Note that when the addend is larger than the divisor, in other words, n < m, then the divider frequency is higher than the addition and the combined output will never trigger. Swing With the switch in the centre position, the right side adds a time delay to the input. The amount of delay, or swing, ranges from 0ms to around 1000ms. In Swing mode, the combined output passes all clocks through until each time the divisor triggers, when it adds a time delay. The result is that every n-th clock is delayed by m, where m is the amount of swing and n is the divisor. As in Count mode, if the divisor frequency is greater than the delay time, the combined output will not trigger. In Swing mode, this is determined by the combination of input clock frequency and delay time. DIY-Kit-Type: THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Φορέω is a triple function processor for triggers, gates and clocks. It simultaneously performs pulse width modulation, multiplication and repetition, with individual input, output and CV for each function.• Pulse width modulation, as a ratio of the input signal rate, is adjustable from 0 to 100 percent. Multiplication also operates on the input signal rate, multiplying it by a factor from 1 to 16.• Repetition generates a burst of triggers, at the rate of the multiplier, with repetitions adjustable from 1 to 16.Each function has two knobs for manual and CV level, and three jacks for trigger input, CV input and trigger output.Pulse width modulation carries through to the outputs of the two other functions, and the three trigger inputs are normalled from top to bottom.When multiply and repeat are combined, Φορέω makes an excellent burst generator, perfect for rolls, flams and fills. The repeater gives precise control over burst length, while the multiplier easily moves from quarter notes, to thirds, to eights, to everything in between and lots more beyond. Go on, give us a snare rush!Φορέω is also extremely versatile with many utility functions, such as master clock doubling, clock modulation, and for triggering and clocking fast sequences. It even works as a square wave overtone generator with PWM, tracking audio input signals up to 20kHz.Φορέω perfectly complements Στοιχεῖα, Λόγοι, Κλάσματα and Χρόνος, completing our Euclidean series of trigger processors.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
The Robaux Decision Tree randomly sends a gate to one of three outputs and then to one of three sub-outputs. Generate unpredictable rhythms. You can choose to route a gate to a single random output or play polyphonic gates. Utilize the knob to transition from total chaos to a repeating loop.The latch mode lets you hold an incoming gate. Pair it with a multimode filter to select various filter types. Use it to alternate between a variety of waveforms. The random input routing injects vibrancy into your sound.The DCSN 3 can also function as a traditional clock divider. The signal is split from half to 1/16 on the top four jacks. Additionally, a continuous sequence is output through the lower eight jacks. Odd divisions enable intricate rhythm creation. Utilize it at audio rate for polyphonic chords using just one square VCO.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The Clock O’Pawn mk2 serves as a versatile clock device, taking on the role of true "chef d’orchestre" for your modular system. Its transport section lets you start, stop, and reset instruments synchronized with its intuitive internal clock or have your setup dance with your MIDI equipment.If you find metronomic clock signals uninspiring, a variety of groove patterns and clock humanization features enable the maestro to guide your setup with distinctive shuffles and swings. To complete this rich set of features in a small yet powerful clock source: presets memory, select bus compatibility, and several handy options to configure the Clock O'Pawn the way it suits you the best.Features:• Clock source module offering four distinct outputs• Transport section with play, pause, stop, tap tempo and manual reset operations• Diverse selection of grooves, ranging from classic swing to experimental clock manipulation• Humanize adding randomisation to the clock timing• Accent output with 27 different patterns• Option menu for customizable preferences• Midi input for external sync with midi devices• Memory of 16 presets• Select bus compatibility• Skiff friendlyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The Time Apprentice is a compact dual configurable clock divider. The dividers have their own set of divisions, perfect for applications such as clocking and resetting sequencers, syncing pingable modulation sources or triggering events. A set of jumpers at the back of the module allows for personalisation of the divider’s behaviour.Features:• Dual clock dividers• Dedicated potentiometer for each divider with two different ratio ranges• 4 jumpers at the back allowing customisation of the dividers (triggers/gates, auto-reset, alternative clocking)• Skiff friendly (25mm deep)• Intellijel and Pulp Logic format supportedDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Casting spells on every boring clock signals, The Time Wizard got a bag full of arcane time-warping tricks. All his magical feats are based on 6 dividers with selectable division factors and 4 switches providing 81 routing variations.This module's occult powers have been harnessed to easily clock and reset other sequencers with odd time signatures, provide weird clock division/multiplication ratios, and create complex poly-rhythmsFeatures:• Sextuple clock divider divided in two sections A and B• Dedicated potentiometer acting on the division factor for each divider• Clock multiplying and weird div / mult ratio abilities for the first section, first section incoming clock can be multiplied by 3 or 4, allowing to get easily triplets from a 16th clock or mult / div association as x4 / 7• Independant clocking or divider association abilities for the second section, so B5 and B6 can get their clock in internaly from B4. For example, associating B4 = /7 and B5 = /16 provide a hit at each clock begining of 4 bars with a 7/4 time signature• Auto-reset available for the first section or the whole module, the autoreset is provided by B6• Additional logic functions for divider A2 : A2 output can provide the following functions : A2 AND B5 or A2 OR A3• Jumper on the back for Trigger or Gate selection for B5 and B6• User replaceable firmware chipDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.