Skip to main content Skip to search Skip to main navigation

Utilities

Filter products

Befaco - Pedal Pow (1U)
Befaco - Pedal Pow (1U)

only 2 left

Power your pedals directly from your Eurorackcase with Pedal POW – a compact dual power supply that delivers two isolated 9 V outputs, each capable of supplying up to 500 mA to run your stompboxes reliably on stage or in the studio.Pedal POW converts your Eurorack +12 V rail to clean 9 V pedal power while sharing the available energy with your modular synth. Because Pedal POW depends on your Eurorack power supply, its total available power cannot exceed what your Eurorack PSU can provide. Make sure your Eurorack power supply has enough headroom to run all installed modules plus anything you connect to Pedal POW.Each Pedal POW output can supply a maximum of 500 mA. Keep in mind the conversion draw: every 1 mA delivered by Pedal POW draws approximately 0.8 mA from the +12 V rail. For example, to deliver the full 500 mA on one output you must provide 500 mA × 0.8 = 400 mA from the +12 V rail. If both outputs are used at their maximum, the pedals would draw 500 mA + 500 mA = 1000 mA, which corresponds to 1000 mA × 0.8 = 800 mA from your +12 V bus.Before connecting multiple high-current pedals, verify your Eurorack power budget and factor in the Pedal POW conversion rate. Use the product’s reference table or this conversion rule (1 mA at Pedal POW ≈ 0.8 mA from +12 V) to quickly calculate how much current you need from your Eurorack supply so you can avoid overloading the system and keep your rig stable.Features:• 1U Intellijel format• Dual power supply with two isolated outputs, each providing 500 mA• Center negative (-) polarityDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€50.00*
Befaco - Pedal S-R (1U)
Befaco - Pedal S-R (1U)

only 2 left

Pedal S-R is the perfect stereo interface for integrating external effects into your Eurorack system. This compact stereo pedal insert adapts hot modular signal levels to the levels and impedance required by stereo or mono stompboxes, pedals and outboard gear, making it simple to route modular sounds through your favorite effects.The Sends section attenuates typical Eurorack signals (≈10 Vpp) down to usable line or instrument levels so pedals behave as intended and clipping is avoided. The Returns section includes a dedicated volume control to blend processed signal back into the modular at a comfortable level, keeping your patch balanced and musical.Pedal S-R also features a Hi-Z switch that lets you select between standard and high-impedance inputs. Flip it when connecting pedals or effects that expect a guitar amp or passive pickups to preserve tone, dynamics and clarity.Features:• Fully compatible with Befaco 7U Case and Intellijel 7U and Palette cases rear Jack connectors• 1U Intellijel format• HI Z switch• Full control over the relationship between your modular system and external pedals or effects unitsDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€73.00*
Befaco - Percall
Befaco - Percall

only 1 left

Percall is a percussive oriented module that will shape four different sound sources into percussive sounds. Percall has four VCAs with dedicated decay envelopes and a mixer, so you can prepare a percussion submix. Added strength input will provide extra dynamics to the sounds! To round up the module, audio inputs are normaled from one to two and from three to four, spicing them up with choke control. This allow to create open and closed Hats or kind of side-chained baselines with your kick.Features:• Four VCAs with dedicated decay envelope.• CV control over envelope decays.• Individual outputs for each envelope• Volume control per channel and normaled Mix out.• Strenght input affecting all four channels.• Audio Input 1 normaled to Input 2. Audio input 3 normaled to input 4.• Choke contrrols, binding Channel one with two and three with four.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.

€165.41*
Befaco - Phono Amp (1U)
Befaco - Phono Amp (1U)

only 2 left

Vinyl culture and modular synths come together in a high-fidelity phono stage built for Eurorack. This compact module brings turntables into the modular domain, letting you run hybrid DJ sets, add scratching and turntablism techniques to patches or simply enjoy your favorite records with true analog warmth.A high-gain amplifier offers selectable RIAA and LINE IN modes plus a ground bonding post to eliminate hum. The stage accepts all common MM cartridges and delivers the gain needed to match vinyl playback to modular levels, preserving dynamics and tonal character.Top-mounted, high-quality RCA connectors make setup and operation fast and hassle-free, keeping cables tidy and accessible during performance. Use this phono stage to integrate turntable textures into modular sound design, expand live sets with vinyl elements or add authentic record playback to the studio.Features:• High-quality RCA connectors• Ground connection for old-school turntables with bidding posts• Hi-gain amplifier with selectable RIAA and LINE INs, and a ground binding post• Accepts all kinds of MM cartridgesDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€73.00*
Befaco - Voltio
Befaco - Voltio

only 2 left

An accurate voltage source and precision adder. Voltio fits somewhere between a music tool and a piece of electronics lab gear.It generates voltages equivalent to all the notes on the 12-tone equal temperament scale throughout a ten-octave range, with an intuitive two-knob interface.The Precision Adder In, lets you sum Voltio’s Out with external voltages.Additionally, the front panel banana connectors let you plug standard multimeter probes for hands-free operation on electronics lab.Use it to transpose Oscillators and sequences in a musical way or as a reference to calibrate your analog gear.Features:• Easily adjust your oscillators in known intervals.• Transpose Musical phrases from sequencers, arpeggiators, or any other notes source.• Calibrate oscillators and filters on your DIY projects or during analog gear maintenance.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.

€94.00*
Befaco / Divkid - Mutes mk2
Befaco / Divkid - Mutes mk2

available

The Mutes mk2, developed in collaboration with Ben Wilson (aka DivKid), is a powerful upgrade to the original performance muting module. Now using VCA-based technology, it delivers improved signal integrity, reduced noise floor, and zero bleed, while preserving the smooth, vactrol-style response. Each channel features a performative three-way switch (momentary–off–on), perfect for live dub-style FX routing and dynamic signal control. Mutes Mk2 enables signal splitting to multiple destinations, expanding your modular performance possibilities. This updated version includes both a standard 3U panel and an additional Intellijel-format 1U panel, allowing for versatile mounting in various Eurorack setups.Features:• LEDs to visualise signals• 3 way momentary – off – on switching• Buffered and cascading normalising of inputs• Black metal panel• VCA based mutingDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€94.01*
Befaco / Molten Modular - Motion MTR
Befaco / Molten Modular - Motion MTR

only 2 left

Motion MTR allow you to mix, attenuate and invert signals while having clear visual feedback of their levels.Each channel can function as:• Audio level control with VU meter• CV attenuator with voltage meter• CV inverter with voltage meterEach input is normalled to 10v, so you can use each of them to generate fixed voltages. Also, the outputs of channels 1 and 2 are summed into Out 3 to be used as a mixer. Patch it wildly to make it work as an attenuverter with offset, as a mixer, a VU meter or a combination of them all!This module is designed in collaboration with Robin Vincent from Molten Modular.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€112.00*
Befaco / Molten Modular - Motion MTR (1U)
Befaco / Molten Modular - Motion MTR (1U)

only 2 left

Motion MTR 1U mixes, attenuates or inverts signals with visual feedback for each channel. Normalled inputs let the controls produce fixed voltages when nothing is patched in. Features: • Three channels for audio level or CV scaling • Meters for signal level and polarity • Normalled 10 V sources for offsets • 34 HP in Intellijel 1U format • Width [HP]: 34 • Depth [mm]: 30 • Format: 1U • Current draw +12 V [mA]: 110 • Current draw -12 V [mA]: 30 • Current draw +5 V [mA]: 0 • Panel / Color: Black Alu • DIY Level: Medium DIY-Kit-Type: THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.

€122.00*
Black Noise Modular - Cosmos
Black Noise Modular - Cosmos

available

Cosmos is a new kind of module that will help you to creating complex modulation, sounds, patterns with ease and will lead you to new sounds territories.Inspired by early analog computers, Cosmos is a unique, innovative, very flexible and fully analog module allowing it to be used as: VCO, LFO, Ring Mod, Polarizer, “VCA”, “LPG”, Phase Lock Loop, Cross-Modulation, Minimum, Maximum, Logic Gates, Waveshaper, Complex gate generator, Fuzz, Distorsion, Gate extractor, Trig extractor, Gate generator, Voltage generator, Trig Generator, comparator, window comparator, complex comparator, Half-Rectifier, Full-Rectifier, Inverter, Buffered Multiples, Mixer, Difference, Compressor, Sidechain, compressor, VC Clipper, VC Switch, Clock doubler, Envelope follower, and more.With its wide fields of application Cosmos can replace many modules but it will also bring new colors to your palette thanks to its unique character. This makes Cosmos the ideal module whether you have a small case or a big system. 100% analog and with an intuitive interface Cosmos is also very easy to use, no menu and button combo problems.Inspired by the past and crafted for the future, 100% analog Cosmos was not only thought to be the center of any system but also to blend perfectly with the rest of your case to form a consistent and coherent system.Cosmos was designed not only to be a swiss army knife module but also to push you to explore and you help create new sounds and explore sonic territories that were previously unattainable.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€260.00*
Black Noise Modular - Dual Buffered Multiple - S (1U)
Black Noise Modular - Dual Buffered Multiple - S (1U)

sold out at the moment

DBM-S is the simplest yet ultimate 1U solution to distribute incoming signals to up to 8 destinations without signal loss, distortion, or interference.DBM-S clever design provides you maximum flexibility, use it a dual channel to create 4 buffered copies of 2 signals or as single channel and get up to 8 buffered copies of the same signal!Build with high-quality components for low noise and high accuracy, DBM-S create perfect copies of the original signal even for pitch CV. After all, quality isn't just a feature, it's our commitment.We believe that form must follows function, but great design blends them seamlessly. With our black and gold signature, DBM-S is not just a high quality utility, it’s a part of a system where each part contributes to the overall strength and quality of this system.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€58.00*
Black Noise Modular - Dual Combinator
Black Noise Modular - Dual Combinator

available

DC is a unique and innovative module that combines the strength of both Averager and Unity Gain mixers without their weaknesses. Along with some additional unique features that make it stand out from other mixers on the market.To create DC we had to rethink the mixer, start from scratch, try new design, prototype many circuits and fail in order to succeed. The result is DC a new type of mixer that offer low noise floor, stable output signal and mix accurately signal without introducing any distortion, clipping, attenuation or unwanted noise and those regardless of the number of inputs signals or their gain.We called this new mixer design a «Combinator,» and the name «DC» stands for «Dual Combinator.» This versatile mixer can function as a dual-channel, mixing up to 3 inputs into a single output, or as a single-channel, allowing up to 5 inputs to be mixed into a single output.We put time and effort into the design of DC because we think that it is an essential module in any Eurorack system. It offers a ratio size, functionality, simplicity that no other mixer offers.DC may seem like a simple utility module, but make no mistake, small things done well can make a big difference.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€73.00*
Black Noise Modular - Dual Combinator - S (1U)
Black Noise Modular - Dual Combinator - S (1U)

only 2 left

DC-S is a unique and innovative module that combines the strength of both Averager and Unity Gain mixers without their weaknesses. Along with some additional unique features that make it stand out from other mixers on the market.To create DC-S we had to rethink the mixer, start from scratch, try new design, prototype many circuits and fail in order to succeed. The result is DC-S a new type of mixer that offer low noise floor, stable output signal and mix accurately signal without introducing any distortion, clipping, attenuation or unwanted noise and those regardless of the number of inputs signals or their gain.We called this new mixer design a «Combinator,» and the name «DC-S» stands for «Dual Combinator.» This versatile mixer can function as a dual-channel, mixing up to 4 inputs into a single output, or as a single-channel, allowing up to 7 inputs to be mixed into a single output.We put time and effort into the design of DC-S because we think that it is an essential module in any Eurorack system. It offers a ratio size, functionality, simplicity that no other mixer offers.DC-s may seem like a simple utility module, but make no mistake, small things done well can make a big difference.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€74.90*
Black Noise Modular - Dual Multi
Black Noise Modular - Dual Multi

only 2 left

DUAL MULTI is a dual buffered multiples.It can be configured as 1 input 6 outputs 1:6 or 2 inputs and 3 outputs each 1:3.Input 2 is normaled to input 1, if nothing is plugged into input 2 you will have 6 copies of input 1 else you will have 3 copies of input 1 and 3 copies of input 2.Buffered multiples have advantages over passive multiples. Since passive multiples split the signal, in case of voltage-critical signal such as V/Oct to VCO, the pitch will vary from one output to the other. With buffered multiples each output will be a perfect copy of the input. Because buffered multis isolate their outputs from the input, any faults or shorts present at the input will not pass through to a connected module.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€69.00*
Black Noise Modular - Dual Rectifier 2
Black Noise Modular - Dual Rectifier 2

only 2 left

Dual Rectifier II is a small yet versatile and essential module for any Eurorack system. It can be used as an AC to DC converter, a distorsion, a complex waveform generator, a frequency doubler, a clock doubler or an envelope follower and more.Like all our modules, Dual Rectifier II is built with high-quality components only and designed to offer the best performance.Whether you're starting a small system or have a wall full of modules, Dual Rectifier II is a must-have for any Eurorack system.DUAL RECTIFIER II is divided into two sections:On top section the Positive Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 1.-Output 2 Half-rectified, signal from input 1 below 0V will be remove.-Output 3 Full-rectified, signal from input 1 below 0V will be rectified.On bottom section the Negative Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 2.-Output 2 Half-rectified, signal from input 2 above 0V will be remove.-Output 3 Full-rectified, signal from input 2 above 0V will be rectified.By default input 2 is normaled to output 1 (inverted) of the top section.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€74.97*
Black Noise Modular - Dual Rectifier 2 - S (1U)
Black Noise Modular - Dual Rectifier 2 - S (1U)

available

Dual Rectifier II - S is a small yet versatile and essential module for any Eurorack system. It can be used as an AC to DC converter, a distorsion, a complex waveform generator, a frequency doubler, a clock doubler or an envelope follower and more.Like all our modules, Dual Rectifier II is built with high-quality components only and designed to offer the best performance.Whether you're starting a small system or have a wall full of modules, Dual Rectifier II - S is a must-have for any Eurorack system.DUAL RECTIFIER II - S is divided into two sections:On top section the Positive Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 1.-Output 2 Half-rectified, signal from input 1 below 0V will be remove.-Output 3 Full-rectified, signal from input 1 below 0V will be rectified.On bottom section the Negative Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 2.-Output 2 Half-rectified, signal from input 2 above 0V will be remove.-Output 3 Full-rectified, signal from input 2 above 0V will be rectified.By default input 2 is normaled to output 1 (inverted) of the top section.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€74.90*
Black Noise Modular - GOMA II
Black Noise Modular - GOMA II

only 1 left

GOMA II is our new take on the classic attenuvertermixer concept. It stands for Generator, Offset, Mixer, Attenuverter.Featuring 4 channels within a 4HP width, GOMA II pushes the boundaries of space efficiency, maintaining intuitive operation and high-end components for max precision (low tolerance resistors, low noise/distortion opamps).GOMA II offers 4 channels to attenuate or polarize (attenuverter) any audio or CV signal. Additionally, each channel can act as a high precision voltage generator (–5V to +5V) to offset another channel or control external parameters.The 4 channels can be processed separately or summed through cascade mixing, which can extend further than a single module since all the GOMA family (I, II, Pro) can be daisy chained to unlock virtually infinite mixing.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€77.00*
Black Noise Modular - GOMA Pro
Black Noise Modular - GOMA Pro

only 1 left

The GOMA Pro pushes the boundaries of the attenuverter-mixer concept.Attenuator, attenuverter, offset generator, voltage generator, waveshaper, distorsion, GOMA Pro can do all of that and more. Engineered for precision, GOMA Pro is crafted using high-quality components to ensure maximum accuracy, including low-tolerance resistors and low-noise op-amps.GOMA Pro offers 3 channels fully analog to amplify (up to x10 gain!), attenuate or polarize (attenuverter) any signal, from CV, audio to line level sources.Additionally, each channel can act as a high precision voltage generator (–10V to +10V) to offset another channel or control external parameters.The 3 channels can be processed separately or summed through cascade mixing, which can extend further than a single module since all the GOMA family (I, II, Pro) can be daisy chained to unlock virtually infinite mixing.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€92.00*
Black Noise Modular - Pipe
Black Noise Modular - Pipe

available

Now introducing PIPE in our sleek Black & Gold theme, featuring a reversible faceplate. Feel like installing your PIPE upside down? No worries – just unscrew the 8 jnuts, flip the faceplate, and put everything back together and Voila! You can now use your PIPE with the connector facing down!With the ability to connect up to 8 inputs or outputs via an ethernet cable, the PIPE-S makes it easy to connect multiple cases together or avoid any cable mess accross a case. This makes it the perfect solution for simply setting up your Eurorack system in the studio or a live gig.But that's not all, PIPE can also be used as a multiple passive 3 section. Want to transmit precise signals like pitch CV and want to avoid crosstalk induced by passive multiples? No worries you can easily deactivate this function for each section from the connector at the back of the module.The best part is that PIPE is completely passive which means you can place it anywhere, it doesn't draw any current from your power supply, which perhaps makes it the simplest DIY module!PIPE modules are sold by pair.The ethernet cable is not supplied with the modulesRegarding Ethernet cableWe recommend shielded Straight-Thru RJ45 cable.Using un-shielded or Crossover cable won't damage your modules but you may experience noise and or mixed channels.Due to its passive nature we also recommend to avoid long ethernet cables.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€77.00*
Black Noise Modular - Pipe - S (1U)
Black Noise Modular - Pipe - S (1U)

only 2 left

With the ability to connect up to 8 inputs or outputs via an ethernet cable, the PIPE-S makes it easy to connect multiple case together or avoid any cable mess accross a case. This makes it the perfect solution for simply setting up your Eurorack system in the studio or a live gig.But that's not all, PIPE-S can also be used as a multiple passive 3 section. Want to transmit precise signals like pitch CV and want to avoid crosstalk induced by passive multiples? No worries you can easily deactivate this function for each section from the connector at the back of the module.The best part is that PIPE-S is completely passive which means you can place it anywhere, it doesn't draw any current from your power supply, which perhaps makes it the simplest DIY module!PIPE-S modules are sold in pairs.The ethernet cable is not supplied with the modulesRegarding Ethernet cableWe recommend shielded Straight-Thru RJ45 cable.Using un-shielded or Crossover cable won't damage your modules but you may experience noise and or mixed channels.Due to its passive nature we also recommend to avoid long ethernet cables.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€78.00*
Black Noise Modular - QBI
Black Noise Modular - QBI

available

The idea behind QBI is to fulfill two fundamental functions when patching:• Duplicate a signal• Invert a signalThese are two basic yet important and essential functions when patching. But even though they are important, we wanted them to take up as little space as possible.Therefore we imagined QBI, a module of only 2HP capable of:• Invert 4 different signals with very high precision.• Duplicate a signal on 3 outputs without losses.• Duplicate and invert a signal on 4 outputs without losses.And the best of all is that you can add these different functions together to always meet your needs when patching.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€73.00*

DIY Kits

At Exploding Shed, we mainly sell DIY kits. This means you'll need to assemble and solder the modules yourself.

We offer different types of DIY kits. Some require you to solder only the mechanical components, such as knobs, jacks, and switches, while others require you to solder every component, from ICs and resistors to capacitors.

You'll find detailed information about the difficulty of each build in the module's product description or in the manufacturer's build guide, which is linked at the bottom of the product page.