Stereo Modules
sold out at the moment
The Sebsongs Modular Sampler DIY kits are now coming with presoldered surface mount components, making the DIY kit faster and easier to build.The Sebsongs Modular SAMPLER is an intuitive 12 bit audio recorder and manipulator designed for short loops and one shots. Sounds can be recorded either with the built in microphone or a mono input jack, which can handle anything from a regular laptop or smartphone to modular level signals. The SAMPLER has granular control of the recorded audio and you can play around with pitch, forward and reverse, start position and loop length (or connect cv/gate to any parameter) to open up a world of interesting sounds!The SAMPLER can be used in looping mode, where for instance time stretch like effects can be obtained easily by modulating the start parameter, or in one shot mode where the reset input is used to trigger playback of the recorded audio and the SAMPLER can function as a drum sample player.The maximum recording length is around 3.5 seconds in the highest sample rate (pitch control fully forward or reverse). If you lower the pitch you get longer recording time. Change the pitch while sampling to obtain pitch fluctuations and tape stop effects.Sound can be recorded either with the built in electret microphone or via mono input jack*. The audio input has enough gain for amplifying regular laptop or smartphone headphone outputs, and the input can also handle modular level signals.* If connecting stereo signal from a laptop / smartphone via either TS or TRS mini jack cable it is advisable to pan the source fully left to avoid distortion.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Panning Stereo Mixer. ST MIXER is effectively a five channel stereo mixer with a really good sounding headphone amplifier built in. It is designed to be the final output module of a small portable system that you want to use with headphones or for recording via 1/8 inch stereo jack cable to a portable recorder.The module consists of three mono channels with level and panning control and one stereo channel with level control and separate inputs for left and right. The stereo headphone output also has level control.ST MIXER is perfect for a starter system with a couple of synth voices and a stereo effect. The headphone output can drive most headphones quite well and also doubles as a recording output to connect to for instance a Zoom recorder.Headphone output power: 6,4 mW @ 73 ohmsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Horrorscape Synthesizer - sculpting feedback into sonic art!Audrey II is a horrorscape synthesizer designed for fearless exploration of feedback. Unpredictable yet compelling, it transforms chaotic sound into immersive soundscapes. From deep, haunting drones to screeching, otherworldly tones, Audrey II is a sonic beast like no other.Feedback Synthesis?What is feedback, really? It’s that magical moment when sound loops on itself, evolving into something wild. With Audrey II, we’re taking feedback to the next level using Karplus-Strong synthesis—a fancy term for turning short bursts of noise into rich, self-sustaining tones. Think digital strings, but way cooler.Digital WitchcraftSome say analog is the only way to get that sound… We were surprised too when we heard the first burst of noise coming through our headphones. That warmth, the grit, the unpredictability—it was all there. But here’s the twist: Audrey II is 100% digital, running on the almighty Daisy Seed platform.Built from the ground up to emulate analog chaos, digital bits power every nuance of Audrey II’s feedback, distortion, and reverb-drenched echoes. It’s pure digital magic that doesn’t just imitate analog—it embraces and amplifies it. What you hear isn’t just a close approximation; it’s a whole new breed of sound that pushes digital synthesis into uncharted territory.Pristine SoundPowered by the Daisy Seed microcontroller, Audrey II delivers 96kHz / 24-bit audio with the speed of an ARM Cortex-M7 at 480MHz. Equipped with 64MB of SDRAM, it handles complex feedback, drones, and effects seamlessly, pushing digital synthesis into rich, analog-like territory.The Signal Flow01. Karplus-Strong Synthesis & DistortionThe signal begins with Karplus-Strong synthesis, a method of string synthesis that creates resonant, droning tones—adding layers of harmonics to emulate organic vibrations, while feedback and distortion weave in raw, aggressive edges.02. ReverbNext, the signal passes through a rich, spacious reverb, allowing the drone and feedback to bloom, creating haunting and immersive atmospheres.03. FiltersFollowing the reverb, Audrey II utilizes high-pass and low-pass filters with a body control to shape the sound further, revealing hidden overtones and harmonic textures that can add either warmth or an eerie sharpness to the feedback.04. Tape Delay EmulationFinally, the signal reaches a tape delay emulator that further degrades and expands the sound, adding layers of movement, modulation, and a classic tape echo feel that’s both nostalgic and unpredictable.05. Stereo OutputTo top it all off, Audrey II’s stereo output widens the soundstage, creating a sense of depth and space that immerses you in rich, layered textures. With stereo feedback flowing through the chain, each element takes on new dimensions, allowing you to push the boundaries of sonic space.Driven & Open SourceAudrey II is a collaborative project born from the Synthux Academy community, where music technology enthusiasts, designers, and engineers come together to push creative boundaries. Developed by Nick Donadson from Infrasonic Audio and designed by Roey Tsemah, founder of Synthux Academy, Audrey II embodies the spirit of exploration and innovation that drives this community.Audrey II’s firmware is available on our GitHub, inviting anyone to dive into the code, make modifications, or build upon its foundation. This open-source approach empowers makers not only to experiment with Audrey II’s sound but to shape its future, contribute enhancements, and share discoveries with the Synthux Academy community. Audrey II is a testament to the creativity that can emerge from collective knowledge and a shared passion for instrument design.Features:• Karplus Strong synth engine• Reverb amount• Reverb size• High and low pass filters• Tape delay emulation• Stereo out• Built on the Daisy Seed• Open sourceDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Discover the Touch 2, an instrument designed for hands-on control and tactile interaction. Easily upload different instruments via USB and start playing instantly!Open source instruments included: BASS // STRING // LOOPER // FX // DRUMS // SLICERCheck out the product page for the complete instrument list, download links, and videos. https://www.synthux.academy/simple-synth/touch2Key Features:Swappable Faceplates: Includes 4 different faceplates for versatile performance.12 Touch Pads: Experience a responsive, tactile performance every time.Powered by the Daisy Seed microcontroller, the Touch 2 delivers incredible sound quality with any instrument you load onto it. Plus, it's fully programmable! Create your own unique instruments using C++, Arduino, Max, or Puredata.Upgrade your music-making experience with the Touch 2. Order now and elevate your performance!Features:• Programmable. All Simple kits come with the Daisy Seed microcontroller and access to our introduction to synth programming video course.• Open source instrument on Github.• Each kit comes with a video course teaching sound fundamentals: https://learn.synthux.academy/• Powerful music instrument for live performances.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
The Threetom Modular Doppio is a compact stereo amplifier, drive, and soft limiter module. Doppio helps complex and dynamic stereo sounds to find their place in a modular synthesizer context, where signals are hot, and headroom is extremely limited. Doppio does this by implementing a compact, yet flexible, soft-knee limiter. The limiter is specifically designed for eurorack levels and avoids the need for unnecessary make-up gain, resulting in a lower noise floor.Doppio offers three different gain settings (x1, x5, x21), and three different ratios (linear, drive, and limit). In addition to this Doppio has gain and volume knobs for more precise control. Different combinations of these settings cater to applications like saturating complex stereo signals without turning them into mush, end-of-chain limiting, and boosting line level signals to eurorack level, while still retaining enough oomph to also saturate them nicely. Finding the right settings is made easy by DOPPIO’s unique coffee-bean-shaped indicator lights.Even though Doppio’s architecture is stereo, that doesn’t mean it has no uses on mono signals: Either process two mono signals with identical settings, or chain the two channels to form a two-stage high-gain mono drive. Finally, it’s important to note that Doppio is DC-coupled and can also be used to process CV signals.In summary: Doppio is to your signals what a double espresso is to you – it makes you bigger and bolder – and you know you’re hooked when the withdrawal symptoms kick in.Features:• Three different maximum levels of gain: x1 (0dB), x5 (+14dB) and x21 (+26dB)• Three different soft-clipping modes: Drive mode, Off / linear mode and Limit mode• Caffeine knob for fine control over the gain applied to the inputs• Volume control for post-gain attenuation• Coffee-bean-shaped indicator lights make finding the desired settings easy• Reverse power protection• 4-layer PCB design with completely separate of audio supply rails and groundDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
3350 VCF uses the AS3350/CEM3350 architecture to provide two two-pole state-variable filters. Each filter offers low-pass or high-pass operation. The filters can run independently, in parallel or stereo, or in series for four-pole filtering. A shared Frequency control and a Separation control move the two cutoff frequencies together or apart.Features:• Two two-pole AS3350/CEM3350 state-variable filters• Low-pass/high-pass selection per filter• Independent, parallel/stereo or serial four-pole operation• Shared Frequency and opposing Separation controls• Resonance up to self-oscillation• A output from filter A; AB output from filter B/final stageDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
DYN is a stereo transient and dynamics processor based on the DSP algorithms of Surreal Machines Crack. Attack and Sustain shape transients, with Gate, Maximizer, Limiter and output Clipper stages for further control. An assignable CV input can modulate one of seven parameters.Features• Stereo transient and dynamics processing• Attack and Sustain controls plus five faders• Gate, Maximizer, Limiter and output Clipper• Assignable 0-5 V CV control of seven parameters• 24-bit converters; 48 kHz DSP processing; approximately 1 ms latencyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Verb is a compact stereo reverb with eight distinct reverb topologies. Send, feedback and tone controls shape the space, while a CV input adds modulation to the Send setting. The left input is normalled to the right input for mono sources.Features:• Eight selectable reverb topologies• Stereo input and output; left input normalled to right• CV control of Send, with +/-5 V input added to the knob setting• 24-bit DSP processing at 48 kHz• Five controls, two buttons and eight indication LEDsDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Ar Merc’het Brao combines a pair of resonant −12 dB filters with two overdrive stages in a compact module; its Breton name translates as "The pretty girls." Configurable for stereo or dual-mono operation and crafted with guitarists in mind, each filter features a switchable mode (Low-Pass or High-Pass) and dedicated CV inputs for voltage control of the cutoff. Global cutoff and resonance controls shape both channels together while the overdrives add harmonic grit and saturation, yielding a versatile tone-shaping device that sits comfortably between modular synthesis and guitar-style processing.Features:• 2 X Resonant 12 dB slope Filter (High Pass/Low Pass)• 2 X Classic Overdrives• Filter Cutoff CV inputs• Global controls for Cutoff and Resonance• Stereo and double mono use• Modular and Guitar friendlyDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Distresañ is a musical Baxandall shelving EQ engineered for smooth, natural tonal shaping. Its bass and treble shelving controls let you gently boost or cut low and high bands, while a fixed mid control at 1 kHz lets you add or remove body without resorting to narrow, surgical boosts.Designed for broad tonal balance rather than corrective notching, Distresañ imparts hi-fi–style clarity and warmth with minimal artifacts, making it ideal for shaping sounds in mixing, mastering, and live reinforcement where a transparent, musical response is required.Features:• Baxandall shelving topology for smooth, musical bass and treble shaping.• Fixed 1 kHz mid control for adding or removing presence and body.• Designed for tonal balance and overall sound sculpting, not narrow corrective EQ.• Hi-fi–style response: natural-sounding adjustments with minimal artifacts or distortion.• Suitable for mixing, mastering, live sound, and general tone shaping.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Sonveskan is a three-channel mixer built from discrete components and germanium transistors, engineered to deliver gritty, analogue warmth and aggressive harmonic colour. Each channel features two serial gain stages (a front-panel drive control plus a PCB trim), voltage-controllable feedback with a dedicated feedback pot and CV input, a mute switch and a direct output. The main channel adds a two-band equaliser and an additional gain stage with its own trim for extra edge and saturation.Patching multiple strips together encourages wild feedback, multi-stage distortion and experimental textures, making Sonveskañ a compact but powerful tool.Features:• Three identical channel strips with dual serial gain stages.• Voltage-controlled feedback per channel with CV input and feedback intensity control.• Mute switches and direct outputs on each channel for flexible routing.• Main channel two-band EQ plus extra gain stage for added grit.• 2017 model fitted with larger coupling capacitors for improved bass response.• Built around germanium transistors and discrete circuitry for vintage, lo-fi character.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Hive is a four-channel stereo mixer offering per-channel CV-controlled panning with the trademark Vostok twists that turn a straightforward mixer into a versatile toolbox for any rack. Each channel includes a boost stage to match levels between modules and to accommodate pro-line devices like desktop synths or drum machines, so signals sit correctly in the mix without extra attenuation or padding.Panning uses a custom law with −1.5 dB attenuation at center, delivering smooth, musically balanced transitions whether adjusted by hand or driven by CV. Rear-panel chaining connectors let multiple Hive units act as channel expanders or submix stages, enabling larger mixes and flexible routing topologies.Housed in just 10 HP, Hive combines compact footprint with practical features for stereo mangling, FX sub-mixing, end-of-line mixing and more, making it a handy utility for both performance and studio patching.Features:• Four-channel stereo mixer with per-channel CV-controlled panning.• Per-channel boost stage for level matching and pro-line device compatibility (desktop synths, drum machines).• Custom panning law with −1.5 dB center attenuation for smooth, musical balance transitions.• Manual or CV control of pan for dynamic stereo movement.• Rear-panel chaining connectors to use additional Hive modules as channel expanders or submixes.• Compact 10 HP footprint that saves space in crowded cases.• Clean summing and routing suited to stereo mangling, FX sub-mixing, or end-of-line mixing.• Robust build and layout focused on fast, hands-on workflow in live and studio setups.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.