Mixer & Att. Various

Percall is a percussive oriented module that will shape four different sound sources into percussive sounds. Percall has four VCAs with dedicated decay envelopes and a mixer, so you can prepare a percussion submix. Added strength input will provide extra dynamics to the sounds! To round up the module, audio inputs are normaled from one to two and from three to four, spicing them up with choke control. This allow to create open and closed Hats or kind of side-chained baselines with your kick.Features:• Four VCAs with dedicated decay envelope.• CV control over envelope decays.• Individual outputs for each envelope• Volume control per channel and normaled Mix out.• Strenght input affecting all four channels.• Audio Input 1 normaled to Input 2. Audio input 3 normaled to input 4.• Choke contrrols, binding Channel one with two and three with four.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.

The Output Bus is your ultimate output module: Presented by DivKid and Befaco, meant to be the last link in your modular chain!Inspired by pro audio and studio summing units the Output Bus allows for summing style mixing, external gear integration, soft clip limiting, flexible output types, headphone monitoring and level visualization.The module works great mixing all your other mixers in your setup, to return mono or stereo FX into the master bus and for bringing in external stereo line level gear with ease. All of this in just 8HP while also being able to visualize your final levels, output appropriate signals on the right cable type and monitor in headphones.Features:• Six stereo inputs.• Line/synth selector in input six.• Modular level minijack out.• 6,5 mm Jack balanced out.• Minijack and 6,5 mm phones out.• Led Vu-meter.• Soft clipping circuit at main output.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.

Stereo Strip takes the idea of a channel strip and makes it modular. We hope that by bringing this long-established component of the audio engineering world into the Eurorack environment and by adding CV control over its key parameters that you will find new, creative ways to use it in your patches!It features stereo inputs and outputs for audio or CV with EQ, voltage controlled panning, stereo VCA, performable mute and input/output level switching for Eurorack or line level uses. Abusing the input level switching allows for some musical, modulate-able and highly shapeable distortion sounds too.Stereo Strip was designed to be a creative part of a modular patch. Creating stereo images from mono sources, shaping and modulating existing stereo images, synthesising stereo pseudo ring modulation, sweetening FX with EQ or drastically wave shaping your oscillators, creating send FX routings with benefits or it can simply be used as a channel strip at the end of chain in a patch.The addition of line level gain boosting (for the input) or reduction (for the output) allow it to work as a stereo input or output interface for external gear with the advantage of the VCA, panning and the EQ to shape the sound. Experiment with bringing external gear into the Eurorack format and then shape and modulate those sounds them on the way in!Try patching Stereo Strip anywhere you would place a VCA in a system and/or explore its EQ and voltage controlled panning, which are rarer additions to the sound sculpting options for the Eurorack format.This module is designed in collaboration with Ben Wilson aka Divkid.Features:• 3 band EQ• Panning (manual and voltage controlled)• VCA level control (manual or voltage controlled)• 3 way performance muting (on-off-momentary)• Soft clipping limiter (distortion!)• Line level input and/or output adjustmentDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

Motion MTR allow you to mix, attenuate and invert signals while having clear visual feedback of their levels.Each channel can function as:• Audio level control with VU meter• CV attenuator with voltage meter• CV inverter with voltage meterEach input is normalled to 10v, so you can use each of them to generate fixed voltages. Also, the outputs of channels 1 and 2 are summed into Out 3 to be used as a mixer. Patch it wildly to make it work as an attenuverter with offset, as a mixer, a VU meter or a combination of them all!This module is designed in collaboration with Robin Vincent from Molten Modular.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

This is the 1U version of the module, for the 3U standard version please check the other product!Motion MTR allow you to mix, attenuate and invert signals while having clear visual feedback of their levels.Each channel can function as:• Audio level control with VU meter• CV attenuator with voltage meter• CV inverter with voltage meterEach input is normalled to 10v, so you can use each of them to generate fixed voltages. Also, the outputs of channels 1, 2 and 3 are summed into Out 4 to be used as a mixPatch it wildly to make it work as an attenuverter with offset, as a mixer, a VU meter or a combination of them all!This module is designed in collaboration with Robin Vincent from Molten Modular.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

Cosmos is a new kind of module that will help you to creating complex modulation, sounds, patterns with ease and will lead you to new sounds territories.Inspired by early analog computers, Cosmos is a unique, innovative, very flexible and fully analog module allowing it to be used as: VCO, LFO, Ring Mod, Polarizer, “VCA”, “LPG”, Phase Lock Loop, Cross-Modulation, Minimum, Maximum, Logic Gates, Waveshaper, Complex gate generator, Fuzz, Distorsion, Gate extractor, Trig extractor, Gate generator, Voltage generator, Trig Generator, comparator, window comparator, complex comparator, Half-Rectifier, Full-Rectifier, Inverter, Buffered Multiples, Mixer, Difference, Compressor, Sidechain, compressor, VC Clipper, VC Switch, Clock doubler, Envelope follower, and more.With its wide fields of application Cosmos can replace many modules but it will also bring new colors to your palette thanks to its unique character. This makes Cosmos the ideal module whether you have a small case or a big system. 100% analog and with an intuitive interface Cosmos is also very easy to use, no menu and button combo problems.Inspired by the past and crafted for the future, 100% analog Cosmos was not only thought to be the center of any system but also to blend perfectly with the rest of your case to form a consistent and coherent system.Cosmos was designed not only to be a swiss army knife module but also to push you to explore and you help create new sounds and explore sonic territories that were previously unattainable.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

The GOMA Pro pushes the boundaries of the attenuverter-mixer concept.Attenuator, attenuverter, offset generator, voltage generator, waveshaper, distorsion, GOMA Pro can do all of that and more. Engineered for precision, GOMA Pro is crafted using high-quality components to ensure maximum accuracy, including low-tolerance resistors and low-noise op-amps.GOMA Pro offers 3 channels fully analog to amplify (up to x10 gain!), attenuate or polarize (attenuverter) any signal, from CV, audio to line level sources.Additionally, each channel can act as a high precision voltage generator (–10V to +10V) to offset another channel or control external parameters.The 3 channels can be processed separately or summed through cascade mixing, which can extend further than a single module since all the GOMA family (I, II, Pro) can be daisy chained to unlock virtually infinite mixing.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

Wonderland is an 8×8 active patchbay/matrix mixer/switcher for both audio and control voltages.Any of the 8 inputs can be patched to any of the 8 outputs simply by pressing the corresponding switches. A patched signal will appear at both normal and inverted outputs simultaneously.A single input can be patched to a single output. A single input can be patched to multiple outputs. Multiple inputs can be patched to a single output. Multiple inputs can be patched to multiple outputs.Each input features a micro-attenuator which can be set with a small screwdriver. This space saving feature allows you to reduce the volume of an incoming signal without having to resort to external attenuators. If you add many inputs to one output you will of course cause clipping (which may or may not be desirable!), the micro-attenuators are your on-board way around this. I find it useful to leave the micro-attenuators set to 50% (which is how they come pre-set at delivery). Of course, their size is a little bit of a compromise, but they are a useful feature nonetheless. Wonderland’s sister module Looking Glass includes full size input attenuators as well as LED status indicators.Features:• 8 inputs (1 through to 8), each with micro-attenuators (which can be set with a small screwdriver)• 8 buffered inverted outputs (A through to H) which are 180o out of phase with the inputs• 8 buffered normal outputs (A through to H) which are in phase with the inputs• A switch matrix of 64 push on/push off switchesDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.

This is the DIY version of this unit.Pathways is a modular matrix mixer designed for feedback manipulation, creative routing, weird synthesis… and many other things.Based around sixteen analog VCAs it can be the central hub of many different setups and a bridge between desktop gear and eurorack systems.Features:• 4x 1/4″ inputs with gain / drive control, 4x 1/4″ outputs• Each of the 16 matrix intersections can be controlled manually or via CV, a dedicated LED gives visual feedback of the channel volume• An envelope follower is normalled to input four, the signal then gets fed through a clock divider with three cascaded outputs. Willingly, an external signal can be inserted into the divider• Two voltage controlled LFOs can modulate any parameter and create dynamic feedbacks, asymmetrical panning, tempo-related fx send/returns• If patched into itself, each channel can self oscillate so it can be used as a polyphonic cv-controllable drone synthesizer• full eurorack compatibility, each parameter has its own 1/8″ input jackDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled unit. The kit includes all parts to build the unit. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

I know what you want: you want to make something go silent, fast.You want nice, tactile clicky goodness. You want half the size, half the price and exactly as much utility - and buddy, you've found it.Introducing the Apnea 3, 3 mutes that'll make your patch go dead quiet in the click of a button. No funky clicks, no weirdness, just a kill switch that kills your incoming CV or audio signal, ready to be revived with another click of the button - and did I mention it's 2hp? Did I mention it's passive and draws no power? Did I mention it's skiff friendly? Did I mention it's really nice and also good?Finally, the unit is designed to be turned either way, for maximum ergonomic pleasure and utility. You can even choose yourself whether pushing the buttons down will mute or unmute. Neat!Also an excellent gift for the unskilled modular musician who insists on not using headphones.Features:• Quick, simple and customizable build.• Very high utility-per-hp factor and no power requirements.• Works well with both CV and audio signals.• Nice tactile buttons without actuation noise bleeding into your signals!DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.

Herzlich Labs - R2R Ladder 8-bit DAC. It's a passive R2R ladder circuit, which will do all kinds of neat things in your system. Use it as an 8-Bit Digital to Analog Converter, punch in a bunch of digital signals in every numbered input, and from the output you shall find a delightful analog signal.Or why not use it as a weird, passive weighted mixer? A fixed-setting attenuator? Why not plug in a bunch of stuff and just see where it takes you? I promise it's safe, thanks to the brilliant design and architecture of the Herzlich R2R.In delightful 3 HP to fill that space left by another odd-sized module.Features:• Passive 8-bit DAC• Use it as a mixer, fixed attenuator or a number of other things• Flexibly use anything as input or outputDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.

Macro ControllerKNOBI is a multi-tool able to mix, attenuate, invert, display and multiply any kind of signal. Knobi can serve a wide range of purposes thanks to its internal signal path that makes use of some of the most useful building blocks of analog synthesis: a 4-channel mixer, a three-range offset, an attenuverter, a fixed manual gate and lastly a cascading multiple derived from the output stage of Agogô.a, b, c and d are Knobi’s inputs while r is a fixed 5v reference output. The toggle switch next to d sets the range of the offset - the big knob below the meter. Connect a signal into one of the inputs to visualize its voltage value in the three digits meter. Keep in mind that this reading happens post offset and attenuverter - the smaller knob with (-) and (+) indications.The pushbutton next to x4 adds a gate of 5v to the mix: with no input connected it will act as a manual gate output. Autopatch the r reference output into one of the inputs to use Knobi as a macro controller thanks the offset knob and switch to set the range and the attenuverter.x1, x2, x3 and x4 are all cascading copies of the final signal path. Plugging a cable will break the normalization and the multiplication will reset starting from the next output. Four cables plugged in will output a copy at the same factor x1 - unity gain - making Knobi a versatile buffered multiple.Features:• Thermally compensated 5v voltage source with dedicated output.• Four channel mixer with four buffered output.• Built in 3 digits voltage meter post mix / attenuation / inversion.• Offset with a dedicated three positions range toggle.• Manual gate button tied to the mix.• 4 cascading outputs in an open design configuration.• Unique signal path: mix - attenuate - invert - add - visualize - multiplicate.• “Whatever” power connector a.k.a. don’t mind the polarity.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

ROSA is a multi-mode crossfader, scanner, and switcher that allows seamless morphing between up to four inputs and outputs. With its three operating modes (Scan, Wave, and Pass), you can easily shape and route signals to fit any patch.Features:• Scan Mode: Morph between up to four inputs with adjustable curves using the KNEE control.• Wave Mode: Independently control the four VCAs for complex dynamic changes.• Pass Mode: Route a single input (or mix multiple inputs) to up to four outputs, perfect for quadraphonic setups or parallel processing.• Infinite Analogue Potentiometer: For smooth, continuous transitions.• Global SHUT Control: CV-controlled mute for immediate silence.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

• Vactrol Mix combines four audio or CV signals into two channels, determined by the random sequence. It’s a great way to create stereo effects, complex waveforms or feedback loops.• This expander is 4 in, 2 out vactrol matrix mixer controlled by the Turing Machine, connected around the back by a 16 pin ribbon cable.• There are four inputs, for audio or CV sources. The four knobs set the level for each input. Next to each knob is a pair of LEDs. When the LED on the left is lit, the signal goes to the left output. When the LED on the right is lit, the signal goes to the right output. The LEDs are controlled by the Turing Machine module. The two outputs are both doubled (mult-ed) to make it easier to patch feedback loops.• Despite being less popular or widespread than Pulses or Volts, this is my favourite Turing Machine expander. It is a unique device that turns mundane source material into wild, unpredictable but rhythmically accessible patterns of sound. It’s a great way to create stereo effects, shifting drones, complex waveforms or feedback loops, and can be the heart of small (but chaotic) system.• Vactrols are electro-optical devices; a light shining on a light-dependent resistor. They have an extraordinary history, from powering the optical soundtracks on the first sound films in the 1920s to studio compressors, the tremolo in Fender guitar amps, and many of Don Buchla's 1970s synth designs. Modern vactrols are an LED pointing at a cadmium light dependent resistor, sealed together in a little black plastic box. Because the LDR reacts relatively slowly, the signals cut together smoothly, with no clicks or pops. Unfortunately, the cadmium in light dependent resistors is banned in Europe, so Vactrols are becoming harder to find.• Feedback is where this module gets really interesting. Try sending the (bottom) left and right outputs to your output mixer, and the (top) left and right outputs to spring reverbs or delays, patching the delay/reverb outputs back into input channels. Carefully ride the input levels, and you'll get snippets of feedback. The main clock speed can have a huge effect on feedback levels, because it takes a while to build up.• There are lots of Vactrol Mix audio examples in my Soundcloud: Twenty Minutes of Madness, Contact Mic Feedback and this ancient track recorded using the breadboard prototype.• The Vactrol Mix is DC coupled, so you can also rhythmically cut up DC sources; mix LFOs at different speeds with audio rate oscilllators, and frequency modulating a pair of oscillators using the two outputs.• This module was inspired by Grant Richter's Cadavre Exquis voltage controlled mixer, which was inspired by André Breton's surrealist game Exquisite Corpse. Richter's mixer also inspired the RxMx module by Make Noise.• Jonathan Higgins, on Facebook: 'There isn't a patch I don't use it on. People often thing you can only use it for crazy stereo percussion (which it is amazing at). But I also often patch all four outputs from the humpback filter into it for evolving stereo drones.'• The Vactrol Mix is a very straightforward through-hole DIY build. If you get stuck, the Github Issue List is probably the best place to start - remember to check closed issues as well as open ones.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.

North Coast makes the Eurorack four-knob utility mixer sound great again with this minimalist design featuring just six transistors. Where a conventional mixer would typically require at least five operational amplifier units each containing a dozen or more transistors, we cut the complexity and distill mixing to its essence. This is a new design made with current components and modern manufacturing quality; but its Class A amplifiers operate on principles that go all the way to the dawn of electronic signal processing.Suitable for both audio and control voltages, with bonus features that don't compromise the minimalist philosophy: positive and negative offset; simultaneous DC- and AC-coupled outputs; maximum gain a little over unity for when you need that extra push over the cliff. It can also function as a transistor distortion effect, by offsetting the signal until it clips and then using the AC-coupled output.Features:• High-quality potentiometers with bushings fastened to the panel for wobble-free operation; conductive plastic for smooth feel• All-new design, not a clone or imitation of anything else• Classic discrete-transistor design style; DIY kit ships with silicon 2N5088 transistors for a clean modern sound, easily modifiable to use other recent or "vintage" types• No ICs!• Through-hole for easy hand construction and maintenance• No compromises on build quality: real aluminum panel, not PCB material, with colour printing; nickel and gold plating on the circuit board; film output coupling capacitor; close-tolerance metal film fixed resistors.• Fully open design - no lock-inDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.

Punch MG is a unique module with VCA-DECAY & Mute GROUP designed for Eurorack systems. This module has been specially designed to generate dynamic percussive sounds while also offering the capability to manage multiple signals simultaneously through its innovative mute group feature.Punch MG provides a versatile platform for designing dynamic percussive sounds. With its mute group feature, it allows you to handle numerous signals concurrently.The manual will guide you through the various features and functions of Punch MG, enabling you to explore its full potential.Key Features: Dynamic Sound Generation: Punch MG is engineered to generate dynamic percussive sounds with finesse, offering a range of creative possibilities.Features:• Mute Group Interaction and Signal Patterning: Utilize the mute group feature to enable interactions between signals that share the same group. This feature enables signal muting and amplitude limitation when multiple signals are triggered simultaneously. The amplitude and decay time of each signal are influenced by others in the same group. This characteristic can lead to captivating pattern variations when focusing on specific channels.• Expandable Capability: By linking two modules, you can expand the effect of the mute group to accommodate up to eight signals, fostering intricate interactions and captivating sonic landscapes.• AM Sound Creation: Connect audio rate signals to the level input to explore the creation of AM (Amplitude Modulation) sounds, further extending the sound design possibilities.• Envelope outs: Each envelope's polarity can be inverted using dedicated switches on the front panel, enabling you to achieve effects like side-chain compression and ducking. Also, the mute group circuit's influence extends to the envelope signal output, providing intriguing modulation capabilities that add a unique layer of creative expression to your sonic endeavors.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

ATTENUVERT x6 is just what it sounds like - six attenuverters in one module!The module consists of six inputs, six outputs and six knobs. Each attenuverter can handle +/- 12V signals. All attenuverters are DC coupled.ATTENUVERT x6 is a very useful utility module for tuning in modulation amplitudes and polarities, but it can also be used to invert gate signals and attenuate audio signals.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.

OFFSET x6 is the perfect sibling to the ATTENUVERT x6 - six DC offset channels in a slim package!The module consists of six inputs, six outputs and six knobs. Each offset channel can offset AC or DC signals with +/- 5V DC. Without any signal connected to the inputs, the outputs generate adjustable +/- 5V DC voltages, which for instance could be handy for offsetting v/oct inputs on a VCO.OFFSET x6 is a very useful utility module for tuning in DC offsets for modulation. Many digital modules only accept unipolar modulation (only positive voltages), and many modulation sources are bipolar (positive and negative voltages). OFFSET x6 makes it possible to “shift” the +/- 5V signal from an LFO to instead being a 0-10V signal. Use it in conjunction with ATTENUVERT x6 to also shape the amplitude and polarity of your modulation sources.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.

Panning Stereo Mixer. ST MIXER is effectively a five channel stereo mixer with a really good sounding headphone amplifier built in. It is designed to be the final output module of a small portable system that you want to use with headphones or for recording via 1/8 inch stereo jack cable to a portable recorder.The module consists of three mono channels with level and panning control and one stereo channel with level control and separate inputs for left and right. The stereo headphone output also has level control.ST MIXER is perfect for a starter system with a couple of synth voices and a stereo effect. The headphone output can drive most headphones quite well and also doubles as a recording output to connect to for instance a Zoom recorder.Headphone output power: 6,4 mW @ 73 ohmsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.

Aeolus Mixer is a 6HP quadraphonic unity mixer. Three quadraphonic inputs and two stereo outputs are mixed to provide a quadraphonic output with 5.1 compatibility.Features:• Quadraphonic unity mixer• 3 quadraphonic inputs with mono and stereo normalisation• 2 stereo inputs with mono normalisation• Cross switch on the second stereo input allowing stereo crossing in the quadraphonic space• 5.1 compatible outputs thanks to the center and sum output in addition to the four main outputs• Jumpers on the back on the module for gain reductionDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.