Sound Sources
sold out at the moment
Analogue drum voice with a broad range of applications. Boom!! can be used to create bass drums, tom toms, chirps, blips and clicks. The heart of the module is a VCO which is built around one half of a LM13700. The VCO has a HIGH/LOW switch as well as a SWEEP control, which defines it’s response to the onboard envelope.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
100% analogue fully modular super flexible drum voice module.Features:•White noise source•Release generator with voltage control•Voltage controlled filter with lowpass and highpass options•Voltage controlled amplifierDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Horror Show is a 4 HP combined noise generator/digital ring modulator/sub oscillator.Noise generator with filter frequency control. Filter is twin-t type. The noise output is normalised to RM X Input and also to the Sub Osc Input, so that 5 types of noise are simultaneously available, all of which can be further affected by twisting the filter frequency knob.Digital Ring Modulator, comparator based. May also be used as a pulse width modulator by patching in any audio waveform and any controller waveform.Sub oscillator with 3 simultaneous outputs: -1 square, -2 square, -2 pulse. May also be used as a clock divider.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Infinitely Maybe is a full featured randomness module, with a number of sources of randomness:• White noise• Pink noise• Sample and hold circuit• Random gates circuitAn onboard CV mixer allows you to mix two different sources into the sample and hold circuit. White noise is normalised to CV input 1, Pink noise is normalised to CV input 2Infinitely Maybe has an onboard clock for triggering the sample and hold circuit. This may be overridden with an external clock if required via the clock in socket.There is a built in LAG circuit, which enables the S/H OUT to slide between voltages at a predetermined rate. This function can be remotely controlled via the LAG INFinally, a random gates output is derived from the S/H Out. With the MAYBE knob at 0 a constant gate is available. The further you turn the MAYBE knob towards 10, the less likelihood of a gate is.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Klang Stadt is the latest FC iteration of Electric Druid’s VCDO digital wavetable oscillator.Features:• CV’d interpolating waveforms• LFO• CV’d subosc waveforms and octaves, CV’d glide, bitcrushing and more!• Frequency CV input accepts 0-5V control voltages• Quantized to semitones, to cover the MIDI note range 0-63• improved PWM filtering• addition of Sub Two output• addition of Klang output• addition of Xmod feature• onboard LFO for riding the wavesDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
20 HP hardwired synth voice for fast set up times, with a decidedly East Coast feel.Monograf is a fixed signal path monophonic synth voice with many unique features, including a number of patch points for flexibilty within a modular setting. Our aim was to design the simplest full featured and good sounding single VCO synth within as small a space as possible, while offering a broad sonic palette and fast setup times.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Full featured, fully modular synthesiser for Eurorack with a pre-patched normalised signal path for quick setup.A combination of the XVCO TWO, Raging Bull 3.0 VCF/VCA, and System X Envelope, where each section can be used completely individually or as part of the larger whole.Onboard LFO for PWM and FM and Noise Source.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Versatile Drum module with 8 vintage sounds. Snare Drum variant. Seismograf is a PIC based drum module featuring coding by Jetroid. There is currently a choice of two PICs which may be used with Seismograf, "BD" and "SD". As you might expect, BD contains a range of 8 bass drums, while SD contains a range 8 of snare drums. The drum sounds are 10 bit encodings of some of our favourite electronic kits from yesteryear (see chart below). It is not possible for the user to load their own sounds onto Seismograf PICs, but there is a chance that we may release alternative drum sets as the years roll (!) by.Features:• Sound 1 808• Sound 2 808• Sound 3 909• Sound 4 SDSV• Sound 5 LM1• Sound 6 DMX• Sound 7 CR78• Sound 8 DRUMTRAKSDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Versatile Drum module with 8 vintage sounds. Base Drum variant. Seismograf is a PIC based drum module featuring coding by Jetroid. There is currently a choice of two PICs which may be used with Seismograf, "BD" and "SD". As you might expect, BD contains a range of 8 bass drums, while SD contains a range 8 of snare drums. The drum sounds are 10 bit encodings of some of our favourite electronic kits from yesteryear (see chart below). It is not possible for the user to load their own sounds onto Seismograf PICs, but there is a chance that we may release alternative drum sets as the years roll (!) by.Features:• Sound 1 808• Sound 2 808• Sound 3 909• Sound 4 SDSV• Sound 5 LM1• Sound 6 DMX• Sound 7 CR78• Sound 8 DM55DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Shapes is a wide ranging and fully analogue oscillator which can perform duties as both auxilliary VCO* as well as VC-LFO. Shapes can be configured to cycle continuously, or to provide one-shot shaped outputs. When set to one-shot mode, Shapes may be used as an ersatz envelope generator.Using the Time knob, Shapes can cycle from as low as 8 seconds (whale song) to as high as 19500Hz (bat beeps).Shapes has 3 simultaneous outputs:sawtooth (+/-5V, 10Vpp)ramp (+/-5V, 10Vpp)triangle (+/-5V, 10Vpp)Additional waveforms may be derived courtesy of the Shape knob. Anticlockwise from 0 achieves progressively logarithmic sawtooths and ramps, whereas clockwise from 0 achieves progressively exponential sawtooths and ramps. The effect of the Shape knob on the triangle waveform is asymmetric, anticlockwise from 0 achieves progressively logarithmic leading edge, whereas clockwise from 0 achieves progressively exponential falling edge. Progressively exponential triangle waveforms can be achieved using the Time CV knob (set Shape knob to 0) providing there is no jack in the Time CV input socketTime CV input provides wide ranging control of time. It is possible to dial in something approaching 1V/oct over a limited range, although Shapes has not been designed to perform as an accurately tracking VCO. In the audio range, Shapes comes into it’s own when used as a ‘daughter’ VCO to an external ‘mother’ VCO by patching the ‘mother’ VCO into Shapes’ Gate In input socket – some impressive oscillator sync style effects can be achieved.Gate In can also be used to initiate waveforms in one-shot mode, where a pulse of any length will cause Shapes to complete one cycle.*Shapes has not been designed to perform as an accurately tracking audio VCO.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
XVCO TWO is essentially the Roland 100M VCO adapted to Euro. There are individual outputs for ramp, square and triangle - an improvement on the original. The six position rotary switch for octaves gives the oscillator plenty of range, with a pitch control to fine tune. An internal LFO (thanks MC202) can be used to introduce FM and/or PWM. Super!We’ve spent a lot of time tweaking the levels of the waveforms relative to 0V to take into account Euro’s +/-12V supply (instead of the 100M’s +/-15V supply). Care has been taken to set XVCO TWO so that it needs only minimal tweaking of the trimmers for scaling. It’s easy to set up without recourse to ‘scopes, frequency counters, and precision reference oscillators! Accurate up to 7 octave too!DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The SEEDS is a complex powerful 8 bit oscillator and can be used as a complete synthvoice.On the sound-design side you might notice some 90's popular music influences. There are two reasons for that. First of all; those sounds are a natural match for the rather modest (8 bit, 16MHz) Atmel chip on the Arduino Nano we're using. That music was made using digital synthesizers using the processors available at the time, and those had to make the most of the chips available at the time, which were quite comparable to the Nano. The second reason is that those sounds are a lot of fun. Once that link became clear it became more a of a guiding principle than a potential problem; it seems more sensible to lean into such links than it is to resist them.The Arduino in the SEEDS kit is already programmed, but in case you need to re-install the firmware you need the Arduino IDE installed on your computer and install the CH340 driver to communicate with the Arduino Nano. The latest Arduino IDE can be downloaded from the Arduino website: https://www.arduino.cc/en/main/software The CH340 driver can be found here: https://sparks.gogo.co.nz/ch340.htmlThe firmware will be updated regularly so you might want to keep an eye on it to get fresh sounds in your SEEDS every now and than.Features:• The original “Grains” sound. Two triangle-wave formant peaks synced by the main oscillator. The “mod” knob sets a formant peak.• Triangle wave with wave-wrapping. The “mod” knob sets the amount of wave-wrapping.• Super-saw, featuring three detuned saw waves with a PWM feature modulated by an LFO.The “Mod” knob controls the LFO rate.• Classic FM; a “carrier” sine wave phase modulated by a second sine. The “mod” knob sets the modulator wave’s pitch offset.• Saw-wave with hard-sync.• Phase-distortion• Tuned noise• Square wave with pulse-width modulation and built in LFO. The “mod” knob controls the LFO rate.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
Legs is an analog kick and percussion synthesizer module in eurorack format.It is based around a triangle core voltage controlled oscillator and a two levels voltage controlled saturation stage.Each parameter has its own dedicated CV input, when a control signal is patched into any of the inputs its corresponding knob will act as a CV attenuator.Two independent gate/trigger input with level control can be used to create accents, pattern changes and generally work on track dynamic.Features:• Triangle core VCO• Two-stage voltage controlled saturation• Two separate gate/trigger inputs• CV control over every parameterDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Liquid Foam is a modular monophonic analog groovebox that revolves around a dual sequencer designed to encourage complex pattern exploration. At the core there’s an analog VCO with two stages of waveshaping, a decay-only EG that can be inverted any step and a 2-pole resonant VCF.Features:• Two sequencers• Newly designed filter and wave mixer• Separate trig and envelope output• Newly added bandpass filter outputDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Hidden beyond the realm of sight and touch, lies a world of electromagnetic signals, hidden to you. This Sensory Enhancement Device™ will allow you to finally achieve the enlightenment of electromagnetic signals you seek. No mere bit-sniffer attached to a jack, this device is an iteration on the Herzlich SEE ALL, but upgraded with 1/4" jacks, hand friendly sizing and stereo pickups.Finally, the strange world of electromagnetism can be heard by human ears in stereo. Move through the world, listening to the harmonies of electric and electronic signals that surround us, and capture them in pristine stereo for later.This is a passive module. It requires amplification to hear the true splendour of the hidden world. Suitable for experimental musicians and field recording enthusiasts alike. A field recorder with a bit of amplification on tap is recommended.Features:• Listen to the secret world of electromagnetic signals - in stereo!• Passive design - never run out of batteries again• Body contacts allow you to become a fleshy antenna• Record an entire experimental noise album in an afternoonDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
HEX cor is a digital polyphonic synthesizer with a capacitive keyboard, potentiometers for signal modulation and an adaptable looper that through its unusual shape explores new ways of interaction and sound synthesis.Features:• Capacitive pads• Recording button• Octave• Waveform• Decay• Loop speed• Loop length• Sync switch• Header pins• 3,5 mm headphone jack output• USB C power portDIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.
only 2 left
Ocelot combines an electroacoustic interface with a compact monitoring station for portable Eurorack systems. Mix two mono signals and a stereo auxiliary source, then listen through the built-in speaker, headphones or balanced stereo outputs. Separate controls set the master, headphone and speaker levels.A built-in contact piezo feeds the mono inputs when no cables are connected and also has a dedicated output. Use it to capture physical interaction with the module, or explore electroacoustic feedback between the piezo and the internal speaker. A direct input overrides the speaker feed, while a rear header provides integration with Jolin Singoli.Features:• Four-input mixer: two mono inputs with level controls and one stereo auxiliary input• Built-in speaker with separate volume control and direct override input (C)• Contact piezo normalized to mono inputs, with dedicated output (O)• Balanced left and right outputs with master volume control• Headphone driver with independent volume control (P)• Electroacoustic feedback between speaker and piezo• Rear connection header for Singoli• Reverse power protectionDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Avalanche Chaotic Oscillator. Black panel version.TABØR is a rhythmic analogue sound and CV source based on the unpredictability of four avalanche transistors oscillators in a continuous oscillation state. These unpredictable core oscillators are related to each other and their charge and discharge cycle creates complex rhythmic textures that can be controlled and triggered with external CV inputs to add more contamination.Features:• Four avalanche oscillators with frequency pulse and cross-modulation controls.• CV inputs on all the parameters.• Starve input to restrict the amount of power supplied to the oscillators.• Color-coded LEDs to provide clear visual reference for the state of each oscillator.• Three outputs: TR for gates, NM for audio, and ZZ for a smoothed fuzz output.• Reverse power protection.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Avalanche Chaotic Oscillator. White panel version.TABØR is a rhythmic analogue sound and CV source based on the unpredictability of four avalanche transistors oscillators in a continuous oscillation state. These unpredictable core oscillators are related to each other and their charge and discharge cycle creates complex rhythmic textures that can be controlled and triggered with external CV inputs to add more contamination.Features:• Four avalanche oscillators with frequency pulse and cross-modulation controls.• CV inputs on all the parameters.• Starve input to restrict the amount of power supplied to the oscillators.• Color-coded LEDs to provide clear visual reference for the state of each oscillator.• Three outputs: TR for gates, NM for audio, and ZZ for a smoothed fuzz output.• Reverse power protection.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
An analogue oscillator with through-zero phase modulation. The core of the T-ZED is the SSI2130 integrated circuit. Voltage controlled wave shape and phase modulation index allow for automated sonic versatility, and 2 separate frequency ranges mean the T-ZED can be used as an audio or CV source.Features:• Simultaneous SINE, TRIANGLE, SAW, SQUARE, and variable SHAPE outputs• Phase MOD input with bipolar INDEX circuit• V/OCT input tracks 10 octaves• FREQ spans 10 octaves, TUNE spans 1 octave• Hard SYNC input• SHAPE output (Sine to Triangle to Saw) with CV input and attenuator• Frequency range HI: 10hz-25khz• Frequency range LO: 0,1hz-200hz• Reverse power polarity protectionDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.