Processors
available
Morphader is a performative tool designed to make multichannel CV/Audio crossfade easy and comfortable. Fading from one quad CV/audio scene to another. The core of the module has four CV controlled crossfaders, each with their individual control and a master fader to control them all. The module mixes the four crossfades at its fourth output, thanks to a clever normalization scheme. Each of them can be easily removed from the mix by plugging a cable at its own output.Features:• CV Controlled four channel crossfader.• Attenuators per input.• Normalized voltages to every input, allowing cv levels morphing.• Audio CV response switch per channel• Master Fader control with Lag.• Leds per channel for signal level monitoring.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Muxlicer is a sequential signal processor designed for add a huge range of special functions to your modular setup in the minimum space.Is divided in three main blocks: a Digital Step Controller, a Gate Generator and an Analog Switch (a.k.a. Mux/DeMux)The module is designed with high “function to HP ratio” philosophy , to have maximum flexibility in minimum space.An analog switch is a device capable of switching or routing analog signals. In the case of Muxlicer, the switch is reversible, so you can send 8 different signals to 1 destination and viceversa.Through Common I/O you can either send a signal to the Mux I/Os or receive a signal from them. (Depending on how the module is connected). It is also used as CV Out when nothing is connected to “All In” or “Mux I/Os”. The eight Mux I/Os are normalled to “All In” jack, so any signal present at this input will go to all of them.Imagine you want to send a signal to steps 1,2,4,5,6 and 8 and two more signals to 3 and 7 respectively. You just need three wires for this: plug the first one to All In and the other two to 3 and 7 Mux I/Os and you are done!Features:• Route any modular signal from one IN up to eight different Outs or vice versa.• Generate CV and Gate signals, been able to work as sequential voltage source a.k.a. sequencer.• Cut audio signals in rhythmical slices with independent volume.• Generate complex and dynamic patterns from any audio or modulation signal.• Create powerful Gate sequences with control voltage retriggering for each step.• Select easily when your signals act on your patch with the Address function.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Percall is a percussive oriented module that will shape four different sound sources into percussive sounds. Percall has four VCAs with dedicated decay envelopes and a mixer, so you can prepare a percussion submix. Added strength input will provide extra dynamics to the sounds! To round up the module, audio inputs are normaled from one to two and from three to four, spicing them up with choke control. This allow to create open and closed Hats or kind of side-chained baselines with your kick.Features:• Four VCAs with dedicated decay envelope.• CV control over envelope decays.• Individual outputs for each envelope• Volume control per channel and normaled Mix out.• Strenght input affecting all four channels.• Audio Input 1 normaled to Input 2. Audio input 3 normaled to input 4.• Choke contrrols, binding Channel one with two and three with four.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Rampage is Befaco’s approach to an old invention: the Serge/Buchla ramp generator.We took the idea of a “patch programmable” function generator/processor, put two units in the same module and expanded them with new functions and ways to combine them: Slope detectors, analogue logic functions and evolved outputs.RAMPAGE APPLICATIONS• Voltage controlled Attack Decay envelope.• Attack Sustain Release Envelope .• More complex ADSR Style Envelope.• Dual VCO. With Square, PWM, Saw, Log, Exp and Triangle shapes. Hard and soft sync.• Gated VCO• VCO + Analog AND Gate (As ADTimbral VCA)• Dual Low Pass Filter• Dual Low pass Filter with VCO soft sync.• Low Pass Filter + AD Envelope• Dual “syncable” voltage controlled LFO with Square, PWM, Saw and Triangle shapes)• Complex LFO . Function combination.• CV controlled and “Ping-Pong” LFO.• Dual Slope detector. Distinguishes when and incoming signal (CV or audio) is rising or falling, and generates gates in concordance.• Comparator. Send a gate when B IN is bigger than A IN• Polyrythmic gate generator. With both channels synced between each other, it generates several “complex rhythm” gates.• Voltage controlled Slew limiter with independent attack and decay control and continuous variable shape between Log, linear and exponential• Peak Voltage follower. Max Out follow the maximum Level of the two inputs.• Minimum Voltage Follower. Min Out follow the minimum level of the two inputs• Envelope follower with adjustable response for rising ans falling flanks.• Voltage controlled Trigger Delay .• Burst Generator.Features:• Built around two voltage controlled Integrators aka Lag Processors.• Convert square signals into ramp waveforms• Achieve “Portamento” or “Glide” effect when applied to pitch CV signals.• Basic lowpass filteringDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
An accurate voltage source and precision adder. Voltio fits somewhere between a music tool and a piece of electronics lab gear.It generates voltages equivalent to all the notes on the 12-tone equal temperament scale throughout a ten-octave range, with an intuitive two-knob interface.The Precision Adder In, lets you sum Voltio’s Out with external voltages.Additionally, the front panel banana connectors let you plug standard multimeter probes for hands-free operation on electronics lab.Use it to transpose Oscillators and sequences in a musical way or as a reference to calibrate your analog gear.Features:• Easily adjust your oscillators in known intervals.• Transpose Musical phrases from sequencers, arpeggiators, or any other notes source.• Calibrate oscillators and filters on your DIY projects or during analog gear maintenance.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
available
Motion MTR allow you to mix, attenuate and invert signals while having clear visual feedback of their levels.Each channel can function as:• Audio level control with VU meter• CV attenuator with voltage meter• CV inverter with voltage meterEach input is normalled to 10v, so you can use each of them to generate fixed voltages. Also, the outputs of channels 1 and 2 are summed into Out 3 to be used as a mixer. Patch it wildly to make it work as an attenuverter with offset, as a mixer, a VU meter or a combination of them all!This module is designed in collaboration with Robin Vincent from Molten Modular.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
This is the 1U version of the module, for the 3U standard version please check the other product!Motion MTR allow you to mix, attenuate and invert signals while having clear visual feedback of their levels.Each channel can function as:• Audio level control with VU meter• CV attenuator with voltage meter• CV inverter with voltage meterEach input is normalled to 10v, so you can use each of them to generate fixed voltages. Also, the outputs of channels 1, 2 and 3 are summed into Out 4 to be used as a mixPatch it wildly to make it work as an attenuverter with offset, as a mixer, a VU meter or a combination of them all!This module is designed in collaboration with Robin Vincent from Molten Modular.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Cosmos is a new kind of module that will help you to creating complex modulation, sounds, patterns with ease and will lead you to new sounds territories.Inspired by early analog computers, Cosmos is a unique, innovative, very flexible and fully analog module allowing it to be used as: VCO, LFO, Ring Mod, Polarizer, “VCA”, “LPG”, Phase Lock Loop, Cross-Modulation, Minimum, Maximum, Logic Gates, Waveshaper, Complex gate generator, Fuzz, Distorsion, Gate extractor, Trig extractor, Gate generator, Voltage generator, Trig Generator, comparator, window comparator, complex comparator, Half-Rectifier, Full-Rectifier, Inverter, Buffered Multiples, Mixer, Difference, Compressor, Sidechain, compressor, VC Clipper, VC Switch, Clock doubler, Envelope follower, and more.With its wide fields of application Cosmos can replace many modules but it will also bring new colors to your palette thanks to its unique character. This makes Cosmos the ideal module whether you have a small case or a big system. 100% analog and with an intuitive interface Cosmos is also very easy to use, no menu and button combo problems.Inspired by the past and crafted for the future, 100% analog Cosmos was not only thought to be the center of any system but also to blend perfectly with the rest of your case to form a consistent and coherent system.Cosmos was designed not only to be a swiss army knife module but also to push you to explore and you help create new sounds and explore sonic territories that were previously unattainable.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Dual Rectifier II is a small yet versatile and essential module for any Eurorack system. It can be used as an AC to DC converter, a distorsion, a complex waveform generator, a frequency doubler, a clock doubler or an envelope follower and more.Like all our modules, Dual Rectifier II is built with high-quality components only and designed to offer the best performance.Whether you're starting a small system or have a wall full of modules, Dual Rectifier II is a must-have for any Eurorack system.DUAL RECTIFIER II is divided into two sections:On top section the Positive Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 1.-Output 2 Half-rectified, signal from input 1 below 0V will be remove.-Output 3 Full-rectified, signal from input 1 below 0V will be rectified.On bottom section the Negative Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 2.-Output 2 Half-rectified, signal from input 2 above 0V will be remove.-Output 3 Full-rectified, signal from input 2 above 0V will be rectified.By default input 2 is normaled to output 1 (inverted) of the top section.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Dual Rectifier II - S is a small yet versatile and essential module for any Eurorack system. It can be used as an AC to DC converter, a distorsion, a complex waveform generator, a frequency doubler, a clock doubler or an envelope follower and more.Like all our modules, Dual Rectifier II is built with high-quality components only and designed to offer the best performance.Whether you're starting a small system or have a wall full of modules, Dual Rectifier II - S is a must-have for any Eurorack system.DUAL RECTIFIER II - S is divided into two sections:On top section the Positive Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 1.-Output 2 Half-rectified, signal from input 1 below 0V will be remove.-Output 3 Full-rectified, signal from input 1 below 0V will be rectified.On bottom section the Negative Rectifier offer 1 input and 3 outputs :-Output 1 is an Inverted copy of input 2.-Output 2 Half-rectified, signal from input 2 above 0V will be remove.-Output 3 Full-rectified, signal from input 2 above 0V will be rectified.By default input 2 is normaled to output 1 (inverted) of the top section.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only 2 left
The idea behind QBI is to fulfill two fundamental functions when patching:• Duplicate a signal• Invert a signalThese are two basic yet important and essential functions when patching. But even though they are important, we wanted them to take up as little space as possible.Therefore we imagined QBI, a module of only 2HP capable of:• Invert 4 different signals with very high precision.• Duplicate a signal on 3 outputs without losses.• Duplicate and invert a signal on 4 outputs without losses.And the best of all is that you can add these different functions together to always meet your needs when patching.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
As its name implies you could think that SLEW/LFO is just a Slew and a LFO packed together but its more than that.We wanted to design a module around the Slew generator which is an underestimate function of a synth. Its often seen and use as a way to make portamento but we've thought it could be more than that.We wanted to design a small module so it could fit in any case. We wanted it to be ergonomic and easy to use despite its size. But we also wanted to pack as much features as possible to make it a "swiss knife module".The result is SLEW/LFO: a 4 HP wide module, that can be used as portamento, AD envelope, LFO, VCO, Filter, Envelope generator and much more.SLEW/LFO is so versatile that we use it in all our patchs, we are very pleased about it and hope you'll like it as much as we are.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Voltage Processor is designed to pack a lot of features in a small module.Here a some of the features you can achieve with Voltage Processor. You can find how to setup those features in the manual below.Features:• Dual VCA• Stereo VCA• CV Crossfader 2:1• CV Crossfader 1:2• Dual AM• CV PAN• Dual Attenuator• Dual Inverter• Dual Offset generator• Dual Voltage generator• Dual Exponential converter• Logarithmic converter• Dual PWM• Dual CV overdrive• Dual waveshaper• Complex waveshaper• Dual RingMod• RindMod• Compressor• Sidechain compressorDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The Garden Listener Eurorack module detects conductivity variations on living beings’ surface and transforms them into MIDI notes and CV signals. For once, leave those LFOs alone, and let any living conductive being modulate your signals. It detects conductivity variations on living beings’ surface and transforms them into MIDI notes, ranging from C-1 to C8, and CV signals (0 – 5V).Its behavior can be tamed through the one-knob menu from which you can choose and modify:• probes’ sensitivity (making it more or less sensitive to current variations)• scale (chromatic, major, minor, indian and arabic)• MIDI channel (from 1 up to 16)• LEDs’ brightnessIt generates trigger, gate, and CV (1V/oct). The CV output behavior can be modified via an octave selector which acts as a “CV equalizer” from which you can choose to generate CV only if the respective MIDI note lies within a certain octave range.The MIDI output allows you to take advantage of the sound of either any synthesizer equipped with a MIDI port or any VST in your DAW.The module comes with 3.5mm white probes and a set of snap-on adhesive reusable electrode pads. A MIDI-TRS type A adapter (not included) is required for the MIDI output.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
only -1 left
The Dannysound Dynamics is a compressor / expander originally designed to process drums but like most processing devices, it can be used for a wide variety of applications.The module comprises of:• Compressor / Expander• Sub Bass Enhancer• 3 Band Inductor-based EQ• Harmonic ExciterThe compressor / expander section uses a discrete transistor-based circuit that allows for soft clipping when overdriven.The envelope detector is known as a feedforward type of circuit; taking it’s input from the signal before it goes to the compressor rather than after.This type of circuit is known for having fast attack times.The Sub Bass enhancer has its own compression circuit that “ducks” the initial transient. This allows the sub bass to be increased without distortionon the transient peaks increasing the overall level.There is a MIX control to allow the unprocessed signal to be mixed back in with the processed signal.The 3 band EQ is an inductor based LCR design. After trying out various EQ topologies this was the design that sounded the nicest.When overdriven it gives a nice “bite” to the sound and it has a certain characterful charm that’s hard to put into words.The controls have a response that are subtle to begin with and get more pronounced as the controls are increased.The Harmonic Exciter adds a little distortion to the high frequencies which bring out the sparkle of cymbals or the snap snare drums.The operating bandwidth can be switched between Low (snare drum snap) or High (Cymbals sparkle).There are inputs for side chaining and control with an external envelope as well as an envelope out to make the envelope detector output available to drive other modules.It also features separate inputs and outputs for the Compressor / Expander and EQ sections, so they could be used as 2 separate modules.Features:• Compressor / Expander• Sub Bass Enhancer• 3 Band Inductor-based EQ• Harmonic Exciter• Envelope In/Out• Sidechain Input• Separate In/Out for Comp/Exp and EQ sectionsDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The Timbre is a 6HP Eurorack module based on the wave folder section of the Buchla 259 oscillator as implemented in the Music Easel.The wave folder adds extra harmonics to input signals that have low harmonic content to creating rich and interesting timbres.Typical input sources to use would be Sine and Triangle waves but you are welcome to try other sources as well!The Dannysound Timbre adds an extra input to the Buchla design to allow 2 oscillators to drive the wave-folder simultaneously –this dramatically increases the range of possible tones that can be generated and allows the folder to go wild!Buchla 259 inspired waveshaper, the perfect module to put in-between your Dannysound Cali and EN129 oscillators!Features:• Osc1 / Osc2 Mix – Adjusts mix between oscillator 1 and 2 inputs, also acts as an attenuator if only one of the inputs is used.• Timbre Control – Adjusts the overall wave fold amount.• Timbre CV – Bipolar (attenuverter) controls the Timbre CV input.• Symmetry – Adds an offset to the input so the top half of the wave starts folding earlier.• Blend – Mixes between the clean and effected sound.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 2 left
This is the Full Kit with a wide assortment of essential components (resistors, capacitors, ICs, transistors) so you can start building right away.Get started in circuit design with MKI x ES Labor. Developed in collaboration with Dr. Shalom D. Ruben teaching professor for engineering at the University of Colorado Labor is a fully-featured circuit design playground and a powerful electronics learning tool all in one. Created with the aim of serving as a universal learning tool for electronics engineering Labor enables users to delve into various aspects of electronics design from fundamental concepts to advanced techniques. Whether you're a beginner exploring the basics or an experienced engineer honing your skills Labor provides a versatile platform for experimentation and learning. Create your own filters oscillators envelopes sequencers – and whatever else you can come up with. Or use it to learn the basics by following along with our series of educational DIY kits.Features:• a built in dual power supply producing eurorack-compatible voltages, with built-in over current protection for safe experimenting• a modular interfacing section with 16 slots for potentiometers, jacks & switches• a pulse/triangle/sine oscillator (audio & LFO range)• a multi mode envelope generator controlled by a premium push button• a buffered variable control voltage source• an output amplifier with variable gain• a dedicated headphone output and a line-level output for recording, processing and analyzing the signal• an expansion slot for installing specialized prototyping tools• a protective lid to cover a breadboard.EDU DIY Labor Full Kit includes:• LABOR• Power Supply Unit• jumper cables• array of interfacing elements like potentiometers, jack sockets, switches• commonly used components (resistors, capacitors, chips, transistors) to start building circuits straight awayNB! LABOR is a testing ground for experiments with electronic circuits and we as a manufacturer cannot by any means diagnose any issues with circuits designed on the LABOR board. We will only respond to support tickets regarding obvious malfunctions of the factory-soldered circuits on the main LABOR board. For other cases of malfunction – please consult other LABOR users/ experienced DIY kit builders on online forums, such as this one. Keep experimenting – keep trying!DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
available
Even though wavefolding is more of a west coast synthesis concept, it’s a great addition to the otherwise very east coast mki x es.edu DIY system. Why? Because it can provide a ton of unusual timbres for your patches: from a slight dash of brightness to harsh metallic drones. That’s why we came up with this super simple BJT-based double wavefolder.We – Erica Synths and Moritz Klein – have developed a series of educational DIY kits under the brand name mki x es.EDU with one specific goal in mind: to teach people with little-to-no prior experience how to design analog synthesizer circuits from scratch. What you’ll find in the box is not simply meant to be soldered together and then disappear in your rack. Instead, we want to take you through the circuit design process step by step, explaining every choice we’ve made and how it impacts the finished module.In total, we have developed 9 kits to build a fully-featured modular monosynth: a sequencer, a VCO, a wavefolder, a noise/S&H module, a mixer, a VCF, an Envelope generator, a dual VCA, and an output stereo mixer with a headphone amplifier. Additionally, an affordable eurorack case with a DIY PSU will also be available. While these kits are easy to build, we did not compromise on design and functionality. We will launch one kit every 4-6 weeks. For each kit, there is an extensive user manual (40+ pages; can be downloaded separately) that will dive deep into not only the electronics behind each circuit but also the fundamental principles of sound synthesis. We hope that the mki x es.EDU project will inspire future engineers and will contribute to the ever-growing diversity of electronic music technology.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
High Towers is a programmable 4 channel voltage controlled clock divider. It is able to receive external clock and reset pulses. Divides the incoming clock pulses by 1, 2, 4, 8, 16, 32, 64 and 128. Each of High Towers 4 assignable outputs can stream any of these divisions.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Trans Europa is a CV processor / generator Module.Features:• Octave switching over 9 octaves• Voltage controlled octave switching, CV input is bipolar +/-5V• Semitone transposition over 1 octave• Voltage controlled semitone transposition, CV input is bipolar +/-5V• 8 Modes (see below)• Glide feature, which can be applied either manually or by external gate.• CV thru, you can patch a 1V/oct voltage source in Trans Europa’s Input, it will be replicated at the Output, with the benefit that all Trans Europa’s features can be applied.Modes• Semitones• Minor 7th• Major 7th• Rick’s Chord• First Fourth Fifth• Diminished• Sustained A• Sustained BDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.