Skip to main content Skip to search Skip to main navigation

Sound Sources

Filter products

ST Modular - Give II (Panel PCB)
ST Modular - Give II (Panel PCB)

available

GIVE V2 is a sonic powerhouse that transcends the boundaries of traditional sound generation. The module is an exceptional analog VCO accompanied by a versatile waveform mixer and three suboctaves.Features:• Classic Analog VCO• 5 Outputs: SAW, TRI, SUB, NOISE, PULSE• 1V/Octave tracking• Pulse Width Modulation with Attenuator• Frequency Modulation with Attenuator• Integrated Waveform Mixer• Skiff friendly design• Wrong Polarity ProtectionDIY-Kit-Type:Panel/PCB Kit. This is a do-it-yourself panel/PCB kit, no parts are supplied, you will need to source them yourself.

€15.90*
ST Modular- Boba Fat (Panel PCB)
ST Modular- Boba Fat (Panel PCB)

available

At its core, Boba Fat features two oscillators that empower producers to easily craft both earth-shaking sub-basses and delicate, enveloping kicks.Features:• Analog Drum Generator• Designed for Kick- and Bassdrums• Two Voices: Soft Mallet and Hard Mallet• Each Mallet may be triggered independently• Internal LFO with Sync• Volume and Boost per Voice• Groove CV Input „Vari“ for Hard Mallet• Mod CV Input for Soft MalletDIY-Kit-Type:Panel/PCB Kit. This is a do-it-yourself panel/PCB kit, no parts are supplied, you will need to source them yourself.

€15.90*
Synthux Academy - Simple Designer
Synthux Academy - Simple Designer

only 1 left

Introducing Simple Designer: the ultimate rapid prototyping instrument for the synth community. Boasting 80 slots for potentiometers, switches, and jacks, plus the capability to incorporate faders and LEDs, it invites endless creativity. Whether you're building from the ground up or iterating on existing designs, Simple Designer, powered by the versatile Daisy Seed microcontroller, is your canvas for creating a full-blown synthesizer. Tailored for designers, makers, and musicians at any skill level, Simple Designer transforms your visionary concepts into tangible, sonic reality with unprecedented ease. Start crafting your masterpiece with Simple Designer today—where your synth dreams become reality.Features:• Programmable. All Simple kits come with the Daisy Seed microcontroller and access to our introduction to synth programming video course.• Open source instrument on Github.• Each kit comes with a video course teaching sound fundamentals: https://learn.synthux.academy/• Powerful music instrument for live performances.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.

€296.00*
Synthux Academy - Simple Fix
Synthux Academy - Simple Fix

sold out at the moment

Unleash your creativity with Simple Fix, the rapid prototyping tool designed for synth designers, makers, and musicians. Powered by Daisy Seed microcontroller, Teensy, or Arduino Nano, it's your quick-start solution to bring ideas to life. Effortlessly add knobs, switches, and jacks, and dive into the limitless world of sound and functionality. Whether you're a pro or a passionate hobbyist, Simple Fix accelerates your design process, transforming inspiration into reality faster than ever. Start your journey towards groundbreaking designs today and unlock your creative potential with Simple Fix—where your next masterpiece begins.Features:• Programmable. All Simple kits come with the Daisy Seed microcontroller and access to our introduction to synth programming video course.• Open source instrument on Github.• Each kit comes with a video course teaching sound fundamentals: https://learn.synthux.academy/• Fits in your pocket.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.

€101.00*
Synthux Academy - Simple Touch
Synthux Academy - Simple Touch

sold out at the moment

Discover Simple Touch, the go-to rapid prototyping instrument for synth enthusiasts, from designers to musicians. Featuring 12 touch pads, 6 potentiometers, two faders, and stereo input/output, all powered by the dynamic Daisy Seed microcontroller. Simple Touch is engineered to bring your sonic visions to life with precision and ease. Dive into a world where your fingertips command the future of sound, blending intuition with innovation. Ideal for both seasoned creators and passionate hobbyists, Simple Touch is your shortcut to prototype, experiment, and elevate your designs. Embrace the power of touch with Simple Touch, and transform your creative impulses into extraordinary musical inventions today.Features:• Programmable. All Simple kits come with the Daisy Seed microcontroller and access to our introduction to synth programming video course.• Open source instrument on Github.• Each kit comes with a video course teaching sound fundamentals: https://learn.synthux.academy/• Powerful music instrument for live performances.DIY-Kit-Type:SMD-Kit-2. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. It includes SMD and through-hole parts! For build guide, more info, videos etc. please check the buttons below.

€118.00*
Synthux Academy - Touch 2
Synthux Academy - Touch 2

sold out at the moment

Discover the Touch 2, an instrument designed for hands-on control and tactile interaction. Easily upload different instruments via USB and start playing instantly!Open source instruments included: BASS // STRING // LOOPER // FX // DRUMS // SLICERCheck out the product page for the complete instrument list, download links, and videos. https://www.synthux.academy/simple-synth/touch2Key Features:Swappable Faceplates: Includes 4 different faceplates for versatile performance.12 Touch Pads: Experience a responsive, tactile performance every time.Powered by the Daisy Seed microcontroller, the Touch 2 delivers incredible sound quality with any instrument you load onto it. Plus, it's fully programmable! Create your own unique instruments using C++, Arduino, Max, or Puredata.Upgrade your music-making experience with the Touch 2. Order now and elevate your performance!Features:• Programmable. All Simple kits come with the Daisy Seed microcontroller and access to our introduction to synth programming video course.• Open source instrument on Github.• Each kit comes with a video course teaching sound fundamentals: https://learn.synthux.academy/• Powerful music instrument for live performances.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€141.00*
Timo Rozendal - 3394 Voice
Timo Rozendal - 3394 Voice

only 2 left

The 3394 Voice is a compact and flexible analog synth voice that packs a full signal chain into one module.VCO, VCF, VCA, envelopes, and noise. Based on the classic 3394 chip, it delivers rich analog tone with selectable square, saw, and triangle waveforms, routed through a juicy 24dB low-pass filter capable of self-resonance and pitch tracking. Two built-in envelopes shape both filter and amplitude, with switchable AD/AR modes for dynamic control. When unpatched, it acts as a constant VCO output, and the mix trimmer allows tonal variation by blending in a square sub, noise, or external signal. Ideal for melodic lines or snappy percussive sounds like kicks, snares, and zaps, the 3394 Voice is both a complete voice and a set of standalone building blocks for your Eurorack system.Features:• VCO with Triangle/Square/Saw waves• Lowpass resonant 24db filter• Square sub oscillator• Analog noise source• Built in VCA and 2 envelopes• Can also be used as separate Filter/VCO/VCA/Noise sourceDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€125.00*
Timo Rozendal - FMP
Timo Rozendal - FMP

sold out at the moment

The FMP is an 8 HP Eurorack FM synthesizer module built around the classic Yamaha YM2413 chip, known for its distinctive sound in vintage game consoles like the MSX, Atari, and Sega systems. Capable of producing everything from clean tones, deep kicks, and noisy snares to bell-like textures and even polyphonic chords, the FMP offers two modes: Tone mode provides a 2-operator FM voice with self-modulating feedback, while Drum mode exposes the chip’s built-in percussion sounds with adjustable levels and pitch. Seven parameters shape the sound and CV interpolation between two parameter sets enables evolving, expressive patterns. While inherently lo-fi, the FMP embraces this character to deliver dynamic, gritty textures, with settings that can be saved for consistent recall. Its charm lies in the unpredictability, offering a rich playground.Features:• 8 HP FM synth voice based on Yamaha YM2413 chip• Two modes: Tone (2-operator FM synth) & Drum (built-in percussion sounds)• Wide sonic range: kicks, snares, hats, bells, chords, and more• Seven tweakable FM parameters• Save and recall settings on power-up• Characterful lo-fi sound with modulator feedback• Adjustable pitch and mix levels in Drum mode• Inspired by classic game console sound chips (MSX, Sega, Atari)DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€114.00*
Timo Rozendal - SDSV+
Timo Rozendal - SDSV+

available

The SDSV+ is a Eurorack drum voice inspired by SyntherJack’s SDSV project and the iconic Simmons SDS5/SDSV drum machine. This enhanced version goes beyond the original by offering expanded sound-shaping capabilities and increased CV control, making it ideal for crafting everything from classic toms, snares, and kicks to hi-hat, crash, and FM-style metallic sounds. If you want to create vintage punch or experimental textures, the SDSV+ delivers dynamic percussion with modular flexibility.Features:• Envelope selection for the VCO and separate Decay pots• Option to use unfiltered noise for click (and the option to turn click off altogether)• Redesigned one of the envelopes to make it independent of input trigger length.• More CV inputs• Noise level controlDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€219.00*
TouellSkouarn - Skorn da Bask
TouellSkouarn - Skorn da Bask

only 2 left

Skorn da Bask is a expert for creating Drones. Its composed 3 analog Oszillator and a low pass filter. The VCOs can not only be used to generate audio signals, but for modulating the VCF’s cutoff frequency as well.Features:• 3 analog OSCillators/LFOs• 1 analog Low Pass Filter (24dB)• Osc 1, 2, 3 CV Modulation input• Filter Audio Input• Filter Modulation inputDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€315.00*
TouellSkouarn – Strakal Orsel
TouellSkouarn – Strakal Orsel

sold out at the moment

Strakal Orsel is a tube distortion module that injects organic, vintage character into a modular setup. True to Touell Skouarn tradition, control labels use Breton terminology, while input and output are marked with arrows for clarity.The unit’s topology offers flexible tonal shaping: the Triodenn selector changes the left tube between pentode and triode operation, altering the core sound. The Boukl Retroaktiñ control combines a feedback engage switch with a level pot that ranges from subtle thickening to full, screaming self-oscillation. Gounid sets the balance between the first and second stages. Ampled governs the amount of saturation. A dedicated CV input, Enkas Modulañ, lets external control influence feedback and overall level even when feedback is not engaged.Beyond straightforward distortion, the circuitry produces rich secondary behaviors. With feedback pushed wide the circuit behaves as a powerful effect oscillator whose pitch responds to CV (not calibrated to strict 1 V/oct tracking). With feedback off and conservative level settings, the unit exposes its tube noise floor and can operate as a raw, characterful VCA.Features:• Tube distortion module• Exposes tube noise floor for characterful texture• Can function as a crude VCA• Compatible with 6j1P, 5654, 6AK5 and EF95 tubes• Boutique construction, made in Plougastel-DaoulasDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€293.00*
Transistorkreis - Random
Transistorkreis - Random

available

The transistorkreis random is a quad true random voltage generator for modulation and for digital noise. There are two inputs to trigger new random voltages and each of the four outputs can be switched to• uniform or normal random distribution,• unipolar or bipolar voltage range,• an amplitude of 5 Vpp or 10 Vpp.Assembling the 3U DIY kit is straightforward since all SMD components are already soldered. Nevertheless, basic knowledge of soldering and electronics is mandatory. The generic design of the transistorkreis random supports any modular format and its firmware is open source. Respectively, you can customize it to suit your requirements. Including screws and washers for your module carrier and a Eurorack power cable with the Eurorack version, which is skiff-friendly.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€179.00*
Transistorkreis - Random (5U)
Transistorkreis - Random (5U)

only 2 left

The transistorkreis random is a quad true random voltage generator for modulation and for digital noise. There are two inputs to trigger new random voltages and each of the four outputs can be switched to• uniform or normal random distribution,• unipolar or bipolar voltage range,• an amplitude of 5 Vpp or 10 Vpp.The generic design of the transistorkreis random supports any modular format and its firmware is open source. Respectively, you can customize it to suit your requirements. Including screws and washers for your module carrier and a Eurorack power cable with the Eurorack version, which is skiff-friendly.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€203.00*
Vostok Instruments - Sena
Vostok Instruments - Sena

only 2 left

Multi Channel Sound SourceVCOs are probably the most popular modules in the Eurorack world.At its most common form, an oscillator module creates different basic waveforms by shaping its core, which gives us several timbres sharing the same frequency.On Sena, we decided to reorganize those principles. We have the basic waveforms as on any VCO, but each has an independent core and frequency control. In addition, the tuning inputs of each channel are daisy-chained, allowing to create easy transpositions or detuning between them.To maximize stability and tracking accuracy, every channel is designed around the famous 3340 oscillator core, present in many legendary synths like the Roland SH-101 and Jupiter-6, Oberheim OB-Xa, and the Sequential Prophet-5.On top of that, the module counts with four dedicated CV-controlled Modifiers to extend the timbral range of each core: a two-stage Folder for the Sine, a Trapezoid shaper for the Triangle, a Phase modulator for the Saw, and a half-range Pulse-width modulator for the Square.The addition of a complete analog Noise Bank makes Sena a super powerful and compact sound source. A cornerstone for any Eurorack setup.Features:• Fully analog VCO circuits: Sine, Triangle, Saw and Square• 1V/Oct pitch tracking over eight octaves• Dedicated CV controlled Wave Modifier on each oscillator• Daisy-chained Freq inputs with onboard buffers• Selectable LFO mode per channel• Analog noise bank with White, Pink, Blue and Brown circuitsDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€240.00*
Weston - 2VL1
Weston - 2VL1

available

2VL1 is a 12HP Eurorack module that offers 2 independent, syncable VCOs and 1 free-running LFO in one compact package. This module uses no rare parts and is an easy to medium DIY build with through hole soldering. This DIY module consists of an assembly of 3 PCBs and robust black anodized 2mm thick front panel with crisp laser engraved graphics.Knob colors might differ from pictures.Kits packed according to Revision 07Features• One VCO with Saw/Pulse/Triangle waves, another with Saw/Pulse• One free-running LFO with square and triangle 20s (50mHz)-30Hz• VCO B syncable to VCO A or external signal• High thermal stability• Extremely good tracking (<4 cents over 7+ octaves typical)• Robust old-school design with all through hole components, large copper traces, and easily obtainable replacement parts.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€212.00*
Weston Audio - AD110
Weston Audio - AD110

sold out at the moment

Drums are the heart! AD110 is a 6-voice analog drum module inspired by the vintage Japanese machines with the same number. The module produces 6 voices; kick drum, snare drum, hand clap, closed hi-hat, open hi-hat, and ride cymbal, all of which are contained in a very compact 16 HP Eurorack module!Knob colors might differ from pictures, currently not all parts are available from time to time.Kits packed according to revision AKFeatures• Faithful recreation of all 6 DR110 voices outputted in Eurorack signal format.• Additional tone adjustments beyond the standard DR110 settings: Kick pitch/resonance, Snare pitch/decay, Cymbal decay, and Clap spread/reverb.• Individual outs + mix out with accent input.• All through-hole parts (DIY Version) and no rare parts.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€269.00*
Weston Audio - B2
Weston Audio - B2

available

Bass and more! B2 contains everything you need to create deep, thumping kick drums or cutting bass lines in one compact 14HP unit: A 1 V/Oct VCO with 4 waveforms, a 3-way waveform mixer with sub-octave sine wave, 2 fast, switchable AR/AD envelope generators, a high quality VCA, and a multi-mode VCF for additional tone shaping!Knob colors might differ from pictures.Kits packed according to Revision AENew features of B2 from B1• New reset/trigger circuit and faster minimum attack times (~25uS) without artifacts• Sub-octave sine• Wave select saw or 2x saw• New VCF with LP/BP/HP selection• Stable voltage references for VCO stability under power supply fluctuations• All OTAs are LM13700 for easy parts sourcingDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€259.00*
Weston Audio - TZ0
Weston Audio - TZ0

available

TZ0 Thru-Zero VCO. Classic analog sound with TZFM! TZ0 is an analog Voltage Controlled Oscillator module in Eurorack format. TZ0 is a triangle-core VCO which is capable of thru-zero linear FM. This VCO has been engineered for extremely good 1 V/oct response over a large tuning range and great thermal stability.Knob colors might differ from pictures.Kits packed according to Revision AGFeatures• Thru-Zero Linear Frequency Modulation.• 5 wave shapes: Sine, Triangle, Sawtooth, Square, & Pulse.• Extremely good tuning linearity.• Built-in high frequency compensation.• Hard Sync input (reset type).• Built in VCA for modulating Linear FM signal with an envelope.• Robust old-school design with mostly through hole components, large copper traces, and easily obtainable replacement parts.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€243.00*
Winterbloom - Castor & Pollux II
Winterbloom - Castor & Pollux II

sold out at the moment

Twins that dance in and out of phase, never completely together but never fully apart, bound to each other in the infinite universe.Castor & Pollux is a dual oscillator that echoes back to the legendary Roland Juno but shines with its own unique, massive voice. It contains two digitally-controlled analog oscillators implemented using a faithfully modernized version of the original Juno 106 design. It builds on the classic ‘80s sounds of its inspiration by using the second oscillator and internal LFO to layer in thick detuned sounds and harmonically complex hard synced waveforms.Castor & Pollux II brings a redesigned interface and moves individual waveform outputs to an included expansion. Both versions have the same features and use the same firmware.DIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.

€290.00*
Wirehead Instruments - Basilisk
Wirehead Instruments - Basilisk

available

Basilisk is a new bass-line exploration synthesizer from Wirehead Instruments, with dual digital oscillators driven into an aggressive MS20-style analog filter coupled with a powerful generative sequencer.Whether you need thumping bass-lines, melodic leads, or percussive tribal beats, the Basilisk is ready to lead you down the rabbit hole from the moment you power it on.The dual oscillators include saw and square/pulsewave, with manual & LFO control over PWM, detune, pitch envelope & glide.The analog filter has a fat saturated drive stage with resonance that can go from subtle to squelching to screaming, and the external audio input can process instruments from your desktop or EurorackAll of this can be sequenced and modulated by the attack/decay exponential envelope, multi-waveform/multi-destination LFO and Elektron-style parameter-locks.The Basilisk is powered by a 1-16-step generative sequencer evolved from the Freaq FM, with multiple algorithms. Explore deep space, underground caverns, deep jungle or 1980s suburbia!Features:Oscillators• 2 digital oscillators - saw, square & pulse• De-tune control that always stays musical, from light flanger to rich chorus, dial it up for fat fifths and octavesAnalog Filter• MS20-style 12dB resonant multi-mode filter• Analog filter drive from -20dB to +20dB saturated overdrive• Low-pass and non-resonant high-pass mode• Digitally-controlled cuttoff modulation• External audio input accepting wide range of signals from 1v p-p to 10vp-pModulation• Attack/Decay envelope with shape control, routable to filter cutoff and/or pitch• LFO with multiple waveforms and configurable destination: cutoff, envelope (attack, decay or depth), note • length, PWM, detune, octave or sequence length• 6 modulation lanes with full 16-step parameter-lock recording of synth parametersGenerative Sequencer• Generative sequencer with 1-16 steps• Multiple generative algorithms including scale-notes, runs, scale-arpeggio, call/response• Sequence mutates/evolves at user-defined rate & note-density• Selectable tonic, octave & scale• Tap-tempo control• Analog sync input & output (Volca, PO or Eurorack compatible with 1/2/4 steps per pulse)Patch Memory• Persistent patch memory saving all digital synth and sequence parametersHardware• Mono audio output (32KHz 14-bit DAC, 4v p-p)• Sync input / output (0-5V rising-edge)                                                              • Audio Input (1v p-p to 10vp-p)• Powered by an Arduino Nano V3!• 142m (w) x 100mm (d) x 40mm (h)• 9-12V DC or micro USB powered (70mA @ 12VDC)DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.

€249.00*

DIY Kits

At Exploding Shed, we mainly sell DIY kits. This means you'll need to assemble and solder the modules yourself.

We offer different types of DIY kits. Some require you to solder only the mechanical components, such as knobs, jacks, and switches, while others require you to solder every component, from ICs and resistors to capacitors.

You'll find detailed information about the difficulty of each build in the module's product description or in the manufacturer's build guide, which is linked at the bottom of the product page.