sold out at the moment
The EZSQ is a simple 8 step sequencer featuring a clock input, reset input and pitch output. It was designed to sit next to the VCSQ2 to give it even more power, but 8 steps sequencers are useful anywhere in all modular cases.Features:• 8 steps• Clock input• Reset input• CV outputDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
only 1 left
Magma is a 10 HP Eurorack compressor with novel circuitry and a classic sound.The Magma uses feedforward diode-bridge compression which gives it a unique character. The Magma excels in providing punch, and can pump hard when set to extreme settings.The interface is easy to control and designed for live performance – it’s easy to change the entire groove with just a few controls. The glass orb lights up like hot lava and visualizes the amount of compression being applied.Sculpt your sound in even more detail with the cv and audio side chain inputs. The Magma aims to make compression both creative and fun!DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Mic from Ginko Synthese is a 2HP Eurorack microphone pre-amp module. It was designed to work with Ginko Sampleslicer but can also be used to amplify and send your microphone signal to any other module in your Eurorack system.It works with electret mics (included).Features:• Input• Gain control• Momentary on push button• On/off switch• Output• Included mini jack microphoneDIY-Kit-Type:SMD-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. All SMD parts are pre-soldered, only trough-hole parts to solder. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
Directly insert your record player into your eurorack setup. The phono amp stage is equiped with RIAA equalization. The module is build with high quality, low-noise opamps and the famous WIMA caps.Features:• gold-plated RCA inputs• PHONO/LINE select• RIAA equalization• GND connection• MONO and STEREO output on modular levelDIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.
sold out at the moment
The SEEDS is a complex powerful 8 bit oscillator and can be used as a complete synthvoice.On the sound-design side you might notice some 90's popular music influences. There are two reasons for that. First of all; those sounds are a natural match for the rather modest (8 bit, 16MHz) Atmel chip on the Arduino Nano we're using. That music was made using digital synthesizers using the processors available at the time, and those had to make the most of the chips available at the time, which were quite comparable to the Nano. The second reason is that those sounds are a lot of fun. Once that link became clear it became more a of a guiding principle than a potential problem; it seems more sensible to lean into such links than it is to resist them.The Arduino in the SEEDS kit is already programmed, but in case you need to re-install the firmware you need the Arduino IDE installed on your computer and install the CH340 driver to communicate with the Arduino Nano. The latest Arduino IDE can be downloaded from the Arduino website: https://www.arduino.cc/en/main/software The CH340 driver can be found here: https://sparks.gogo.co.nz/ch340.htmlThe firmware will be updated regularly so you might want to keep an eye on it to get fresh sounds in your SEEDS every now and than.Features:• The original “Grains” sound. Two triangle-wave formant peaks synced by the main oscillator. The “mod” knob sets a formant peak.• Triangle wave with wave-wrapping. The “mod” knob sets the amount of wave-wrapping.• Super-saw, featuring three detuned saw waves with a PWM feature modulated by an LFO.The “Mod” knob controls the LFO rate.• Classic FM; a “carrier” sine wave phase modulated by a second sine. The “mod” knob sets the modulator wave’s pitch offset.• Saw-wave with hard-sync.• Phase-distortion• Tuned noise• Square wave with pulse-width modulation and built in LFO. The “mod” knob controls the LFO rate.DIY-Kit-Type:THT-Kit-1. This is a Do-It-Yourself kit, not an assembled module. The kit includes all parts to build the module. Only trough-hole parts to solder. Make sure to check the build guide before you buy. For build guide, more info, videos etc. please check the buttons below.