Based in Leipzig, Germany, Exploding Shed have been supplying curated DIY synthesiser kits, modules and components from leading manufacturers since 2016. As enthusiastic nerds dedicated to synthesisers and DIY of all kinds, they are passionate about developing, producing and distributing products they genuinely believe in.
available
5 Touch Points in black. We made them as an extension for our Touch Source, but of course you can use them without the module for wireless patching in your Eurorack system. We made them higher and smaller than comparable products or most DIY versions, so the Touch Points are easily accessible between cables and buttons in your system.
available
5 Touch Points in orange. We made them as an extension for our Touch Source, but of course you can use them without the module for wireless patching in your Eurorack system. We made them higher and smaller than comparable products or most DIY versions, so the Touch Points are easily accessible between cables and buttons in your system.
sold out at the moment
Explore wireless patching through Touch Points! Touch Source generates voltages between -10V and +10V, in the center is a touch plate with GND/0V. Place the Touch Points on any CV input of a module and connect a voltage to the Touch Point via your fingers. Or connect two Touch Points from any input to output through your body. Rule #1 is: there are no rules!Here is a review on Amazona (german) and some demo videos here and there.Touch Source includes 2 black Touch Points. Packs of 5 Touch Points are available separately in black or orange to visualize your signal flow. Packs of 2 indicator Touch Points with bi-plar LEDs are also available.The unit is pre-assembled and no DIY.
available
100% analog dry / wet control.Modular weather protection.The Exploding Shed Umbrella keeps you dry while the patch cable pattern brings a bit of brightness to grey days.Compact at 33 x 6 x 6 cm when folded. Opens up to around 100 cm of rain coverage. Lightweight and ready when the weather turns.
available
The double-walled Weducer Cup with a capacity of 350 ml is a sustainable, premium reusable cup featuring the Exploding Shed logo. The dark outer shell is made from iconic coffee material containing recycled coffee grounds, while the colourful interior and drinking lid are made from plant-based polymers. The price includes a drinking lid and a fully sealable lid.Free for every order over €550 (brutto): if you pay more than €550, you’ll receive a free Weducer Cup as a giveaway.Delivery includes a random colour combination of coffee/cardamom (grey) or coffee/nutmeg (brown). If you have a preference, please indicate this during checkout.
available
The Exploding Shed Workbench Mat provides a reliable, well-organised surface for assembling Eurorack DIY kits, repairing electronics and carrying out soldering work.Its antistatic design helps protect sensitive electronic components from electrostatic discharge. The included adjustable wrist strap, coiled grounding cables and earth bonding plug connect the user and mat to a suitable grounding point, creating a more controlled, ESD-safe workspace when correctly installed.Multiple integrated compartments keep screws, tools and small components organized and within easy reach. The three upper compartments are magnetic, helping prevent metal screws, nuts and other small parts from moving around or becoming lost while you work.A built-in ruler marked in both millimetres and inches makes it easy to take quick measurements directly at the workbench. The spacious central work area provides plenty of room for PCBs, Eurorack modules and other electronic assemblies.The removable ESD mat insert can also be taken out and used separately, providing a flexible antistatic work surface wherever it is needed.Made from durable, heat-resistant material, the mat is suitable for soldering and helps protect the workbench from heat, scratches and everyday wear. Its non-slip surface remains stable during detailed assembly and repair work and is easy to clean after use.Features• Designed for assembling Eurorack DIY kits• ESD-safe, antistatic work surface• Removable ESD mat for separate use• Adjustable grounding wrist strap• Coiled grounding cables and earth bonding plug• Heat-resistant and suitable for soldering• Magnetic compartments for screws and other metal parts• Multiple storage areas for tools and small components• Integrated ruler with millimetre and inch markings• Spacious central area for PCBs and Eurorack modules• Durable, non-slip and easy to cleanIncludes• Exploding Shed Workbench Mat• Removable ESD mat insert• Adjustable ESD wrist strap• Coiled grounding cables• Earth bonding plug
available
If you experience a hum on devices which are USB powered it might be that you have a ground-loop interference on the audio line. These isolators can be placed inbetween to solve it. Comes with small 3.5mm cable.
available
Holder for 4mm hex bits. You can use this one with Exploding Shed's Knurled Nut Tool Pro.
sold out at the moment
The IC Extractor is an essential tool for safely removing integrated circuits (ICs) from sockets without risk of damage. Designed for DIP chips and other socketed components, it helps prevent bent pins and static damage, ensuring a secure and efficient extraction process.
sold out at the moment
This is a pro-version of our tool for the M6 knurled and smooth slotted nuts for Thonkiconn and similar audio connectors used in Eurorack. The vinyl tool body comes with a 4 mm hex bit, which you can use with most standard handles available from hardware stores. Compared to the original tool from our 4x Nut Tool Set this makes the assembly much easier when you have to assemble many nuts in a row. It's a good investment for small maker brands and professional DIYers.The tool is made for hand-operation, not for machines like electric drills or electrical screwdrivers, as this might damage the tool or steel pins.It comes equipped with 2 inserted hardened steel pins plus 6 replacement pins. The tool features 6 holes in total, means 2 alternative pin positions. If pins break after time, you pull them out with a small precision pliers and replace them with new pins using the other holes.The tool works for PCB panels and also thicker aluminum panels. The handle is not part of the product and has to be purchased separately.• For knurled and smooth nuts• Works with M6 nuts (Thonkiconn...)• Feat. 4mm hex bit for standard handles• Replacable hardened steel pins• Incl. 6 replacement pins• 2 alternative pin positions for maximum lifetime
sold out at the moment
Eurorack LED Patch Cables. Make your system glow!Flexible, half transparent PTFE material with extremely nice, rubbery feeling. 3,5 mm (1/8") TS mono connectors on both sides. Each plug features a red/green LED and lights up red when positive and green when negative voltage passes through it. The LEDs on the other sides's plug are always reverse and will have the opposite color.Please have in mind that the LEDs are powered by your CV or audio signal and need some voltage to operate. Means you can expect a very small voltage drop and you have to test if it's ok to use them for your 1v/oct signals. For normal audio and all sorts of CV it's definitely ok.Available in packs of 5 pieces each:• 90 cm length• 3,5 mm connectors
available
These mini side cutters with a stripping function are perfect for synth DIY projects. They automatically adjust to wire sizes from 0.4 to 1.6 mm (26–14 AWG), allowing for precise cutting and stripping.Available in blue and red – the color is chosen at random.More infos on how to use this cleaning tool you can find in our Synth DIY Guides.
available
Reliable standard miniatur SPDT on/on switch with solder lugs.Dimensions:Width 13 mmDepth 8 mmHeight 10 mm
available
Dual Potentiometer, vertical PCB mount.Rotation angle approx. 300°. 6,35 mm Round shaft for knobs with set screw, shaft length 15 mm including thread. 7 mm mounting hole required in the front panel.Nut and washer included.
available
Eurorack LED Patch Cables. Make your system glow!Sexy slimline LED patch-cables made of very flexible TPE material with a nice soft and rubbery feel. Each connector features a red and blue LED, which alter by polarity of your signal. They feature slim aluminum-shell connectors with Exploding Shed logo engraving. The LEDs shine out of the top and bottom of the connector what also illuminates the sockets of your module. Please have in mind that the LEDs are powered by your CV or audio signal and need a certain current/voltage to operate properly. Means also you can expect a very small voltage drop and you have to test if it's ok to use them for your 1v/oct signals. For normal audio and all sorts of CV it's definitely ok.Available in 4 lengths in packs of 5 pieces each:• 15 cm (black)• 30 cm (white)• 45 cm (orange)• 60 cm (green)
sold out at the moment
Side Brackets 3U – 3D Printed – Standard Rails – Type A – Black• Affordable alternative to aluminum side panels• Thread strips or slide nuts can be inserted without disassembling the frame• Smoothly rounded corners provide a perfect finish to the railsImportant: This product includes only the side panels (always sold as a pair) – not rails or complete frames!To assemble, you will also need rails, M5 screws, and thread strips or slide nuts.Other manufacturers may refer to these parts as side parts, side cheeks, or side panels.With these brackets, you can easily build Eurorack frames and mount them in a DIY case.Calculate the required width as follows: rail length + 2 × 3 mm.There are different rail types on the market – these brackets are specifically designed for our Tech Creation Lab Rails.They may also be compatible with other brands, but we strongly recommend checking carefully before purchasing.If you buy all components from us, perfect compatibility is guaranteed.Standard Rails vs. Low Profile RailsThe side brackets for standard rails can also be used with low-profile rails.This results in a small overhang at the back – however, it’s not visible and therefore not an issue.Type A vs. Type BDo not mix them! Type A and Type B components are not compatible with each other.Height: 3U & 1U – What does that mean?• A standard Eurorack module has a height of 3U.• 5U refers to the larger Moog format, which is less common.• 6U means two rows of 3U each.• 1U is the smaller tile format, available in two variants: Intellijel and Pulp Logic.We focus on the Intellijel format.
sold out at the moment
Side Brackets 3U - Aluminium - Standard Rails - Type A - Black• Precisely milled edges, at which the rails sit - these make the resulting construction torsion-proof• You can insert threaded strips or slide-nuts without dismounting the frame• Super precise production• Beautifully rounded corners match the lid of the rails• Fully anodized aluminium• Made in germany, supports local economyThis is only the brackets (always one pair), NOT the rails or whole frames! You need additional rails, M5 screws and threaded strips or slide-nuts. Others might call them side-parts, side-cheecks or side-panels.Our aluminium side brackets are the best on the market! They are definitely not cheap but have some clever advantages and are very precise and made in germany!With these brackets you can easily build stable and precise Eurorack frames and mount them in your DIY case. Just take your rail length + 2x3mm and you have the resulting width of your frame.There are some different rail types on the market - these are made for the Exploding Shed rails. Might fit for others, but you should have a closer look before. We won't take scratched side brackets back! When you buy all stuff here, you are sure that all fits together in the end.Standard Rails vs. Low Profile RailsIt is possible to use the side brackets made for standard rails with low profile rails instead Then you have an overhang at the back, but who cares, as you don't see it later.Type A vs. Type BNever mix Type A with Type B stuff! That won't fit.Height: 3U & 1U - What does it mean?One normal Eurorack module is 3U in height. 5U would be the bigger Moog format, but we're mainly all Eurorack addicts here. 6U is basically 2 rows a 3U then. 1U is the smaller "tile" format which exists as Intellijel size and the less prominent Pulp Logic size. We focus on Intellijel size here.Screws vs. BracketsAll side brackets are 3mm thick. With the standard M5 countersunk screws it might happen that the transition between threading of the screw and screw head (where it's still slim) looks slightly through the bracket in direction of the rail. To make the bracket really sit 100% tight on the side of the rail, you probably have to use a countersink (drill) like this (https://www.obi.de/senker/lux-handsenker-hss-12-mm/p/4949624) or this (https://www.obi.de/senker/lux-senker-comfort-12-mm/p/5816764) to open the hole on the rail side a bit and make sure the last 1/4mm or so of the screw head can sink through the bracket into the hole of the rail itself. Then the construction will be maximum stable. You have to do that yourself.
sold out at the moment
Side Brackets 3U - Aluminium - Standard Rails - Type A - Silver• Precisely milled edges, at which the rails sit - these make the resulting construction torsion-proof• You can insert threaded strips or slide-nuts without dismounting the frame• Super precise production• Beautifully rounded corners match the lid of the rails• Fully anodized aluminium• Made in germany, supports local economyThis is only the brackets (always one pair), NOT the rails or whole frames! You need additional rails, M5 screws and threaded strips or slide-nuts. Others might call them side-parts, side-cheecks or side-panels.Our aluminium side brackets are the best on the market! They are definitely not cheap but have some clever advantages and are very precise and made in germany!With these brackets you can easily build stable and precise Eurorack frames and mount them in your DIY case. Just take your rail length + 2x3mm and you have the resulting width of your frame.There are some different rail types on the market - these are made for the Exploding Shed rails. Might fit for others, but you should have a closer look before. We won't take scratched side brackets back! When you buy all stuff here, you are sure that all fits together in the end.Standard Rails vs. Low Profile RailsIt is possible to use the side brackets made for standard rails with low profile rails instead Then you have an overhang at the back, but who cares, as you don't see it later.Type A vs. Type BNever mix Type A with Type B stuff! That won't fit.Height: 3U & 1U - What does it mean?One normal Eurorack module is 3U in height. 5U would be the bigger Moog format, but we're mainly all Eurorack addicts here. 6U is basically 2 rows a 3U then. 1U is the smaller "tile" format which exists as Intellijel size and the less prominent Pulp Logic size. We focus on Intellijel size here.Screws vs. BracketsAll side brackets are 3mm thick. With the standard M5 countersunk screws it might happen that the transition between threading of the screw and screw head (where it's still slim) looks slightly through the bracket in direction of the rail. To make the bracket really sit 100% tight on the side of the rail, you probably have to use a countersink (drill) like this (https://www.obi.de/senker/lux-handsenker-hss-12-mm/p/4949624) or this (https://www.obi.de/senker/lux-senker-comfort-12-mm/p/5816764) to open the hole on the rail side a bit and make sure the last 1/4mm or so of the screw head can sink through the bracket into the hole of the rail itself. Then the construction will be maximum stable. You have to do that yourself.
available
Side Brackets 3U - Aluminium - Standard Rails - Type B - Silver• Precisely milled edges, at which the rails sit - these make the resulting construction torsion-proof• You can insert threaded strips or slide-nuts without dismounting the frame• Super precise production• Types B have non-anodized edges• Made in germany, supports local economyThis is only the brackets (always one pair), NOT the rails or whole frames! You need additional rails, M5 screws and threaded strips or slide-nuts. Others might call them side-parts, side-cheecks or side-panels.Our aluminium side brackets are the best on the market! They are definitely not cheap but have some clever advantages and are very precise and made in germany!With these brackets you can easily build stable and precise Eurorack frames and mount them in your DIY case. Just take your rail length + 2x3mm and you have the resulting width of your frame.There are some different rail types on the market - these are made for the Exploding Shed rails. Might fit for others, but you should have a closer look before. We won't take scratched side brackets back! When you buy all stuff here, you are sure that all fits together in the end.Standard Rails vs. Low Profile RailsIt is possible to use the side brackets made for standard rails with low profile rails instead Then you have an overhang at the back, but who cares, as you don't see it later.Type A vs. Type BNever mix Type A with Type B stuff! That won't fit.Height: 3U & 1U - What does it mean?One normal Eurorack module is 3U in height. 5U would be the bigger Moog format, but we're mainly all Eurorack addicts here. 6U is basically 2 rows a 3U then. 1U is the smaller "tile" format which exists as Intellijel size and the less prominent Pulp Logic size. We focus on Intellijel size here.Screws vs. BracketsAll side brackets are 3mm thick. With the standard M5 countersunk screws it might happen that the transition between threading of the screw and screw head (where it's still slim) looks slightly through the bracket in direction of the rail. To make the bracket really sit 100% tight on the side of the rail, you probably have to use a countersink (drill) like this (https://www.obi.de/senker/lux-handsenker-hss-12-mm/p/4949624) or this (https://www.obi.de/senker/lux-senker-comfort-12-mm/p/5816764) to open the hole on the rail side a bit and make sure the last 1/4mm or so of the screw head can sink through the bracket into the hole of the rail itself. Then the construction will be maximum stable. You have to do that yourself.